EN ISO 10563:2023

Building and civil engineering sealants - Determination of change in mass and volume (ISO 10563:2023)

This document specifies a method for the determination of the change of mass and the change of volume of self-levelling and non-sagging sealants used in joints in building construction.
NOTE            This test procedure is not intended to determine the absolute maximum value of loss of mass and volume of a tested sealant, but it is an indicative measurement of the loss of mass and volume under specified parameters.

Dichtstoffe im Hoch- und Tiefbau - Bestimmung der Änderung von Masse und Volumen (ISO 10563:2023)

Dieses Dokument legt ein Verfahren zur Bestimmung der Änderung von Masse und Volumen von selbst nivel
lierenden und fließbeständigen Fugendichtstoffen fest, die zur Abdichtung von Fugen im Hochbau verwendet werden.
ANMERKUNG Dieses Prüfverfahren ist nicht zur Bestimmung des absoluten maximalen Masse- und Volumenverlustes von geprüften Fugendichtstoffen vorgesehen. Dennoch liefert es Anhaltswerte für den Masse- und Volumenverlust unter bestimmten Parametern.

Mastics pour bâtiments et ouvrages de génie civil - Détermination des variations de masse et de volume (ISO 10563:2023)

La présente Norme internationale spécifie une méthode pour la détermination des variations de masse et de volume des mastics auto-nivelant et non coulables utilisés dans des joints dans la construction immobilière.
NOTE            Cette procédure d’essai n’a pas pour objectif de déterminer la valeur maximale absolue de perte de masse et de volume du mastic testé, mais c'est une mesure indicative de la perte de masse et de volume avec des paramètres spécifiés.

Tesnilne mase za stavbe in gradbene inženirske objekte - Ugotavljanje spremembe mase in prostornine (ISO 10563:2023)

Standard ISO 10563:2017 določa metodo za ugotavljanje spremembe mase in prostornine samoizravnalnih in nepolzečih tesnilnih mas, ki se uporabljajo za stike v stavbah.

General Information

• Status: Published
• Publication Date: 04-Jul-2023
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: CEN/SS B02 - Structures
• Drafting Committee: CEN/SS B02 - Structures
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 05-Jul-2023
• Completion Date: 05-Jul-2023
• Ref Project: SIST EN ISO 10563:2023 - Building and civil engineering sealants - Determination of change in mass and volume (ISO 10563:2023)

Relations

• Replaces: EN ISO 10563:2017 - Buildings and civil engineering works - Sealants - Determination of change in mass and volume (ISO 10563:2017)
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10563:2023
01-september-2023
Nadomešča:
SIST EN ISO 10563:2017
Tesnilne mase za stavbe in gradbene inženirske objekte - Ugotavljanje spremembe
mase in prostornine (ISO 10563:2023)
Building and civil engineering sealants - Determination of change in mass and volume
(ISO 10563:2023)
Hochbau - Fugendichtstoffe - Bestimmung der Änderung von Masse und Volumen (ISO
10563:2023)
Mastics pour bâtiments et ouvrages de génie civil - Détermination des variations de
masse et de volume (ISO 10563:2023)
Ta slovenski standard je istoveten z: EN ISO 10563:2023
ICS:
17.060 Merjenje prostornine, mase, Measurement of volume,
gostote, viskoznosti mass, density, viscosity
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
SIST EN ISO 10563:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 10563:2023

---------------------- Page: 2 ----------------------
SIST EN ISO 10563:2023


EN ISO 10563
EUROPEAN STANDARD

NORME EUROPÉENNE

July 2023
EUROPÄISCHE NORM
ICS 91.100.50 Supersedes EN ISO 10563:2017
English Version

Building and civil engineering sealants - Determination of
change in mass and volume (ISO 10563:2023)
Mastics pour bâtiments et ouvrages de génie civil - Hochbau - Fugendichtstoffe - Bestimmung der
Détermination des variations de masse et de volume Änderung von Masse und Volumen (ISO 10563:2023)
(ISO 10563:2023)
This European Standard was approved by CEN on 27 June 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10563:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 10563:2023
EN ISO 10563:2023 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 10563:2023
EN ISO 10563:2023 (E)
European foreword
This document (EN ISO 10563:2023) has been prepared by Technical Committee ISO/TC 59 "Buildings
and civil engineering works" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2024, and conflicting national standards shall
be withdrawn at the latest by January 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10563:2017.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 10563:2023 has been approved by CEN as EN ISO 10563:2023 without any modification.


3

---------------------- Page: 5 ----------------------
SIST EN ISO 10563
...