EN 14188-2:2004

Joint fillers and sealants - Part 2: Specifications for cold applied sealants

This European Standard specifies the classes of cold applied joint sealants used in concrete pavements according to their applications and performance characteristics. Furthermore, the requirements and respective test methods for the different classes including the third party surveillance system are stipulated.

Fugeneinlagen und Fugenmassen - Teil 2: Anforderungen an kalt verarbeitbare Fugenmassen

Dieses Dokument legt die Anforderungen an normale und treibstoffbeständige Fugenmassen für Kaltanwendung in Betondecken fest, die bei Straßen, Parkdecks, Brückentafeln, Flugplätzen und sonstigen Verkehrsflächen verwendet werden sollen.
Dieses Dokument deckt nicht die Anwendung an Tankstellen, an Nachfüllstationen für Turbinentreibstoff auf Flugplätzen sowie in der chemischen Industrie ab.

Produits d'obturation et de scellement de joints - Partie 2 : Spécifications pour produits de scellement appliqués à froid

Ce document spécifie les exigences applicables aux produits de scellement courants et résistants aux hydrocarbures pour les chaussées en béton utilisées dans la construction de routes, parkings à étages, tabliers de ponts, aérodromes et autres zones de circulation.
Ce document ne couvre pas l'utilisation dans les stations service, les stations de carburant des aérodromes et l'industrie chimique.

Polnilne in tesnilne mase za stike – 2. del: Specifikacije za tesnilne mase, ki se vgrajujejo po hladnem postopku

General Information

• Status: Published
• Publication Date: 07-Dec-2004
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 227 - Road materials
• Drafting Committee: CEN/TC 227/WG 3 - Materials for concrete roads including joint fillers and sealants
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 14-Feb-2022
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/124 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on road construction products
• Ref Project: SIST EN 14188-2:2005 - Joint fillers and sealants - Part 2: Specifications for cold applied sealants

Relations

• Revised: FprEN 14188-2 - Joint fillers and sealants - Part 2: Specifications for cold applied sealants
• Effective Date: 11-Dec-2010

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Polnilne in tesnilne mase za stike – 2. del: Specifikacije za tesnilne mase, ki se vgrajujejo po hladnem postopkuFugeneinlagen und Fugenmassen - Teil 2: Anforderungen an kalt verarbeitbare FugenmassenProduits d'obturation et de scellement de joints - Partie 2 : Spécifications pour produits de scellement appliqués a froidJoint fillers and sealants - Part 2: Specifications for cold applied sealants93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 14188-2:2004SIST EN 14188-2:2005en01-junij-2005SIST EN 14188-2:2005SLOVENSKI
STANDARD



SIST EN 14188-2:2005



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14188-2December 2004ICS 93.080.20English versionJoint fillers and sealants - Part 2: Specifications for cold appliedsealantsProduits d'obturation et de scellement de joints - Partie 2 :Spécifications pour produits de scellement appliqués à froidFugeneinlagen und Fugenmassen - Teil 2: Anforderungenan kalt verarbeitbare FugenmassenThis European Standard was approved by CEN on 4 November 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14188-2:2004: ESIST EN 14188-2:2005



EN 14188-2:2004 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Classification and specification.5 5 Requirements.6 6 Evaluation of conformity.10 7 Marking, labelling and packaging.11 Annex A (normative)
Initial Type Testing and frequencies of testing for Factory Production Control.13 Annex B (informative)
Example of a product data sheet.14 Annex C (informative)
Processing information for installation of cold applied joint sealants.16 Annex ZA (informative)
Clauses of this European Standard addressing essential requirements or other provisions of EU Directives.17 Bibliography.21
SIST EN 14188-2:2005



EN 14188-2:2004 (E) 3 Foreword This document (EN 14188-2:2004) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2005, and confl
...