iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 161:1991

(Main)

Automatic shut-off valves for gas burners and gas appliances

Automatic shut-off valves for gas burners and gas appliances

This European Standard specifies the safety, constructional and performance requirements for automatic gas shut-off valves for gas burners and gas appliances, hereafter referred to as valves. It also gives the test procedures for evaluating these requirements and information necessary for the purchaser and the user.  It applies to valves with a declared maximum working pressure up to and including 4 bar for use on burners or in appliances for use with one or more fuel gases of the 1st, 2nd or 3rd families.  It applies to electrically operated shut-off valves and to shut-off valves actuated by fluids if the control valves for these fluids are actuated electrically. The external, electrical switch that switches the control signal or the actuating energy is not covered by this standard.

Automatische Absperrventile für Gasbrenner und Gasgeräte

Diese Europäische Norm legt Anforderungen an die Sicherheit sowie Bau- und Betriebsanforderungen an automatische Absperrventile für Gasbrenner und Gasgeräte, nachstehend Ventile genannt, fest. Sie beschreibt auch die Prüfverfahren, nach denen die Einhaltung dieser Anforderungen beurteilt wird und nennt die für den Käufer und Anwender erforderlichen Informationen.

Robinets automatiques de sectionnement pour brûleurs à gaz et appareils à gaz

La présente norme européenne précise les spécifications de sécurité, de construction et de fonctionnement des robinets automatiques de sectionnement pour brûleurs à gaz et appareils à gaz, dénommés ci-après 'robinets'. Elle donne aussi les procédures d'essais permettant de vérifier la conformité à ces exigences ainsi que les informations nécessaires à l'acheteur et à l'utilisateur.

Samodejni zaporni ventili za plinske gorilnike in plinske aparate

General Information

Status
Withdrawn
Publication Date
11-Jun-1991
Withdrawal Date
13-Nov-2001
ICS
23.060.20 - Ball and plug valves
Technical Committee
CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Drafting Committee
CEN/TC 58 - Safety and control devices for burners and appliances burning gaseous or liquid fuels
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
14-Nov-2001
Completion Date
14-Nov-2001
Directive
2009/142/EC - DIRECTIVE 2009/142/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 30 November 2009 relating to appliances burning gaseous fuels
90/396/EEC - Appliances burning gaseous fuels
Mandate
M/BC/CEN/89/6 - Standardization request to CEN concerning appliances burning gaseous fuels
Ref Project
SIST EN 161:1997 - Automatic shut-off valves for gas burners and gas appliances

Relations

Amended By
EN 161:1991/A1:1996 - Automatic shut-off valves for gas burners and gas-burning appliances
Effective Date
22-Dec-2008
Amended By
EN 161:1991/A2:1997 - Automatic shut-off valves for gas burners and gas appliances
Effective Date
22-Dec-2008
Replaced By
EN 161:2001 - Automatic shut-off valves for gas burners and gas appliances
Effective Date
22-Dec-2008

Buy Standard

EN 161:1997EN 161:1997
PreviousNext
Standard
EN 161:1997
English language
37 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Samodejni zaporni ventili za plinske gorilnike in plinske aparateAutomatische Absperrventile für Gasbrenner und GasgeräteRobinets automatiques de sectionnement pour bruleurs a gaz et appareils a gazAutomatic shut-off valves for gas burners and gas appliances27.060.20Plinski gorilnikiGas fuel burners23.060.20Zapirni ventili (kroglasti in pipe)Ball and plug valvesICS:Ta slovenski standard je istoveten z:EN 161:1991SIST EN 161:1997en01-marec-1997SIST EN 161:1997SLOVENSKI
STANDARD



SIST EN 161:1997



SIST EN 161:1997



SIST EN 161:1997



SIST EN 161:1997



S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 15714-6:2022(Main)
Industrial valves - Actuators - Part 6: Hydraulic linear actuators for industrial valves - Basic requirements
SIST EN 15714-6:2022

This document specifies basic requirements for piston type hydraulic linear actuators for industrial valve, both double acting and single acting, used for on-off and modulating control duties. It includes criteria, method and guidelines for design, qualification, corrosion protection, control and testing.
It does not apply to hydraulic actuators which are integral parts of control valves. Other requirements, or conditions of use, different from those indicated in this document, are expected to be subject to negotiations, between the purchaser and the manufacturer/supplier, prior to order.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15714-3:2022(Main)
Industrial valves - Actuators - Part 3: Pneumatic part-turn actuators for industrial valves - Basic requirements
SIST EN 15714-3:2023

This document specifies basic requirements for pneumatic part-turn valve actuators, both double acting and single acting, used for on-off and modulating control duties.
It includes guidelines, recommendations and methods for enclosure and corrosion protection, control and testing.
It does not apply to pneumatic actuators which are integral parts of control valves and to pneumatic actuators designed for permanent immersion in fresh or sea water.
Other requirements, or conditions of use, different from those indicated in this document, are expected to be subject to negotiations, between the purchaser and the manufacturer/supplier, prior to order.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15714-5:2022(Main)
Industrial valves - Actuators - Part 5: Pneumatic linear actuators for industrial valves - Basic requirements
SIST EN 15714-5:2022

This document provides basic requirements for piston type pneumatic linear actuators for industrial valve, both double acting and single acting, used for on-off and modulating control duties.
It includes criteria, method and guidelines for design, qualification, corrosion protection, control and testing.
It does not apply to diaphragm actuators and to pneumatic actuators which are integral parts of control valves.
Other requirements, or conditions of use, different from those indicated in this document, are subject to agreement, between the purchaser and the manufacturer/supplier, prior to order.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16135:2006/A1:2019(Amendment)
Industrial valves - Ball valves of thermoplastics materials - Amendment 1 (ISO 16135:2006/Amd 1:2019)
SIST EN ISO 16135:2006/A1:2019
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 331:2015(Main)
Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings
SIST EN 331:2016

1.1 This European Standard specifies the characteristics for the construction, performance and safety of ball valves and closed bottom taper plug valves. It also details the test methods and marking provisions.
It applies to metallic valves not directly buried for domestic and commercial installations inside or outside of buildings, using gases of the first, second and third family (specified in EN 437) and working up to 0,2 × 105 Pa, 0,5 × 105 Pa, 1 × 105Pa, 5 × 105 Pa and 20 × 105Pa and with temperature limits from -5 °C or −20 °C to + 60 °C.
NOTE   "Not directly buried" within the context of this standard means that valves below ground are not in direct contact with earth or other materials e.g. that they are in a protected encasement.
1.2 Valve nominal sizes (DN) covered by this European Standard are as follows: 6, 8, 10, 12, 15, 20, 25, 32, 40, 50, 65, 80, 100.

  • Standard
    45 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17292:2015(Main)
Metal ball valves for petroleum, petrochemical and allied industries (ISO 17292:2015)
SIST EN ISO 17292:2016

ISO 17292:2015 specifies the requirements for a series of metal ball valves suitable for petroleum, petrochemical, natural gas plants, and related industrial applications.
It covers valves of the nominal sizes DN:
-      8, 10, 15, 20, 25, 32, 40, 50, 65, 80, 100, 150, 200, 250, 300, 350, 400, 450, 500, 600;
corresponding to nominal pipe sizes NPS:
-      ¼, ⅜, ½, , 1, 1 ¼, 1 ½, 2, 2 ½, 3, 4, 6, 8, 10, 12, 14, 16, 18, 20, 24;
and applies for pressure designations:
-      Class 150; 300; 600; 800 (Class 800 applies only for valves with threaded and socket welding end);
-      PN 16, 25, 40, 63, 100.
It includes provisions for testing and inspection and for valve characteristics as follows:
-      flanged and butt-welded ends, in sizes 15 ≤ DN ≤ 600 (½ ≤ NPS ≤ 24);
-      socket welding and threaded ends, in sizes 8 ≤ DN ≤ 50 (¼ ≤ NPS ≤ 2);
-      body seat openings designated as full bore, reduced bore, and double reduced bore;
-      materials.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1983:2013(Main)
Industrial valves - Steel ball valves
SIST EN 1983:2014

This European Standard specifies requirements for industrial steel ball valves having flanged, threaded, socket welding or butt welding ends.
The DN range is:
-   DN 4 ; DN 6 ; DN 8 ; DN 10 ; DN 15 ; DN 20 ; DN 25 ; DN 32 ; DN 40 ; DN 50 ; DN 65 ; DN 80 ; DN 100 ; DN 125 ; DN 150 ; DN 200 ; DN 250 ; DN 300 ; DN 350 ; DN 400 ; DN 450 ; DN 500 ; DN 550 ; DN 600 ; DN 650 ; DN 700 ; DN 750 ; DN 800 ; DN 850 ; DN 900.
The PN and Class ranges are:
-   PN 6 ; PN 10 ; PN 16 ; PN 25 ; PN 40 ; PN 63 ; PN 100 ;
-   Class 150 ; Class 300 ; Class 600 ; Class 900 ; Class 1 500 ; Class 2 500 ; Class 4 500.
This European Standard applies to steel ball valves mainly used for industrial and general purpose applications. However, they can be used for other applications provided the requirements of the relevant performance standard are met.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13547:2013(Main)
Industrial valves - Copper alloy ball valves
SIST EN 13547:2014

This European Standard applies to copper alloy ball valves for general use having, flanged, threaded, capillary or compression or loose nut/union body ends.
This European Standard does not apply to copper alloy ball valves for drinking water applications.
This European Standard specifies the design and performance requirements including materials, pressure/temperature ratings for the shell and body seats, dimensions, test procedures and marking.
For some specific fields of application, for example gas, valves to this European Standard can be used provided the requirements of the relevant performance standards are met. Approval by the relevant regulatory body may be required.
The range of nominal sizes is DN 6 to DN 300 and of nominal diameters 6 mm to 110 mm.
The range of pressure designations covered is PN 6 ; PN 10 ; PN 16 ; PN 20 ; PN 25 ; PN 32 ; PN 40 ; PN 63 ; Class 150 and Class 300.
For the applicability of each nominal size/diameter and each pressure designation to the different types of valve end, see 4.1.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13082:2008+A1:2012(Main + Amendment)
Tanks for transport of dangerous goods - Service equipment for tanks - Vapour transfer valve
SIST EN 13082:2009+A1:2012

This European Standard covers the vapour transfer valve, used for the transfer of vapour between the tank compartment and the pipework connecting to the vapour collection adaptor.
This European Standard specifies the performance requirements and the critical dimensions of the vapour transfer valve. It also specifies the tests necessary to verify the compliance of the equipment with this European Standard. The equipment specified by this standard is suitable for use with liquid petroleum products and other dangerous substances of Class 3 of ADR [2] which have a vapour pressure not exceeding 110 kPa at 50 °C and petrol, and which have no sub-classification as toxic or corrosive.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13709:2010(Main)
Industrial valves - Steel globe and globe stop and check valves
SIST EN 13709:2011

This European Standard specifies the requirements for steel globe and globe stop and check valves which are wrought, cast or fabricated in straight, angle or oblique pattern with end connections flanged, butt welding, socket welding or threaded.
This standard is applicable to steel globe and globe stop and check valves mainly used for industrial and general purpose applications. However, they can be used for other applications provided the requirements of the relevant performance standards are met.
The range of nominal sizes covered is:
DN 8; DN 10; DN 12; DN 15; DN 20; DN 25; DN 32; DN 40; DN 50; DN 65; DN 80; DN 100; DN 125; DN 150; DN 200; DN 250; DN 300; DN 350; DN 400.
DN 8 and DN 12 are not used for PN designated flanged end connections.
DN 8, DN 10 and DN 12 are not used for Class designated flanged end connections.
Socket welding end valves and threaded end valves are limited to the range DN 8 to DN 65.
The range of pressure designations covered is:
a)   for flanged and butt welding end valves:
-   PN 10; PN 16; PN 25; PN 40; PN 63; PN 100;
-   Class 150; Class 300; Class 600.
b)   for socket welding end valves and threaded end valves:
-   PN 40; PN 63; PN 100;
-   Class 600; Class 800.
NOTE   Class 800 is a Class designation widely used for socket welding and threaded end valves.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day