EN ISO 25178-3:2012
(Main)Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification operators (ISO 25178-3:2012)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification operators (ISO 25178-3:2012)
This part of ISO 25178 specifies the complete specification operator for surface texture (scale limited surfaces)
by areal methods.
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft - Teil 3: Spezifikationsoperatoren (ISO 25178-3:2012)
Dieser Teil von ISO 25178 legt den vollständigen Spezifikationsoperator für die Oberflächenbeschaffenheit (skalenbegrenzte Oberflächen) fest.
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 3: Opérateurs de spécification (ISO 25178-3:2012)
La présente partie de l'ISO 25178 spécifie l'opérateur de spécification complet pour l'état de surface (surfaces
à échelle limitée) par des méthodes surfaciques.
Specifikacija geometrijskih veličin izdelka (GPS) - Tekstura površine: ploskovna - 3. del: Operatorji specifikacij (ISO 25178-3:2012)
Ta del standarda ISO 25178 določa popolni operator specifikacij za teksturo površine (površine omejenega obsega) s ploskovnimi metodami.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 25178-3:2012
01-september-2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND*367HNVWXUDSRYUãLQHSORVNRYQD
GHO2SHUDWRUMLVSHFLILNDFLM,62
Geometrical product specifications (GPS) - Surface texture: Areal - Part 3: Specification
operators (ISO 25178-3:2012)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 3: Spezifikationsoperatoren (ISO 25178-3:2012)
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 3:
Opérateurs de spécification (ISO 25178-3:2012)
Ta slovenski standard je istoveten z: EN ISO 25178-3:2012
ICS:
17.040.20 Lastnosti površin Properties of surfaces
SIST EN ISO 25178-3:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 25178-3:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 25178-3:2012
EUROPEAN STANDARD
EN ISO 25178-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2012
ICS 17.040.20
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 3: Specification operators (ISO 25178-3:2012)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 3: Opérateurs de spécification Oberflächenbeschaffenheit: Flächenhaft - Teil 3:
(ISO 25178-3:2012) Spezifikationsoperatoren (ISO 25178-3:2012)
This European Standard was approved by CEN on 6 July 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-3:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 25178-3:2012
EN ISO 25178-3:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 25178-3:2012
EN ISO 25178-3:2012 (E)
Foreword
This document (EN ISO 25178-3:2012) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2013, and conflicting national standards shall be withdrawn at
the latest by January 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 25178-3:2012 has been approved by CEN as a EN ISO 25178-3:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 25178-3:2012
---------------------- Page: 6 ----------------------
SIST
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.