EN ISO 3452-2:2006
(Main)Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials (ISO 3452-2:2006)
Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials (ISO 3452-2:2006)
SO 3452-2:2006 specifies the technical requirements and test procedures for penetrant materials for their type testing and batch testing. It also details on-site control tests and methods.
Zerstörungsfreie Prüfung - Eindringprüfung - Teil 2: Prüfung von Eindringprüfmitteln (ISO 3452-2:2006)
Dieses Dokument legt die technischen Anforderungen und die Prüfverfahren für die Musterprüfung und die Chargenprüfung von Eindringprüfmitteln fest. Es enthält auch Einzelheiten zu den vor Ort anzuwen¬denden Kontrollprüfungen und Verfahren.
Essais non destructifs - Examen par ressuage - Partie 2: Essais des produits de ressuage (ISO 3452-2:2006)
L'ISO 3452-2:2006 spécifie les exigences techniques et les modes opératoires d'essai applicables aux produits de ressuage dans le cadre des essais de type et de lot. Elle détaille également les essais et méthodes d'essai de contrôle sur site.
Neporušitveno preskušanje - Penetrantski preskusi - 2. del: Preskušanje penetrantskih snovi (ISO 3452-2:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2007
1DGRPHãþD
SIST EN ISO 3452-2:2001
Neporušitveno preskušanje - Penetrantski preskusi - 2. del: Preskušanje
penetrantskih snovi (ISO 3452-2:2006)
Non-destructive testing - Penetrant testing - Part 2: Testing of penetrant materials (ISO
3452-2:2006)
Zerstörungsfreie Prüfung - Eindringprüfung - Teil 2: Prüfung von Eindringprüfmitteln (ISO
3452-2:2006)
Essais non destructifs - Examen par ressuage - Partie 2: Essais des produits de
ressuage (ISO 3452-2:2006)
Ta slovenski standard je istoveten z: EN ISO 3452-2:2006
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 3452-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2006
ICS 19.100 Supersedes EN ISO 3452-2:2000
English Version
Non-destructive testing - Penetrant testing - Part 2: Testing of
penetrant materials (ISO 3452-2:2006)
Essais non destructifs - Examen par ressuage - Partie 2: Zerstörungsfreie Prüfung - Eindringprüfung - Teil 2: Prüfung
Essais des produits de ressuage (ISO 3452-2:2006) von Eindringprüfmitteln (ISO 3452-2:2006)
This European Standard was approved by CEN on 7 August 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3452-2:2006: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 3452-2:2006) has been prepared by Technical Committee CEN/TC 138
"Non-destructive testing", the secretariat of which is held by AFNOR, in collaboration with
Technical Committee ISO/TC 135 "Non-destructive testing".
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by February 2007, and conflicting national
standards shall be withdrawn at the latest by February 2007.
This document supersedes EN ISO 3452-2:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
INTERNATIONAL ISO
STANDARD 3452-2
Second edition
2006-08-15
Non-destructive testing — Penetrant
testing —
Part 2:
Testing of penetrant materials
Essais non destructifs — Examen par ressuage —
Partie 2: Essais des produits de ressuage
Reference number
ISO 3452-2:2006(E)
©
ISO 2006
ISO 3452-2:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 3452-2:2006(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Classification. 2
4.1 Testing products. 2
4.2 Sensitivity levels. 2
5 Testing of penetrant materials . 3
5.1 Testing facilities. 3
5.2 Reporting . 3
5.3 Tests. 4
6 Test methods and requirements . 6
6.1 Appearance . 6
6.2 Penetrant system sensitivity . 6
6.3 Density . 11
6.4 Viscosity . 11
6.5 Flashpoint. 12
6.6 Washability (Method A penetrants). 12
6.7 Fluorescent brightness . 12
6.8 UV stability . 13
6.9 Thermal stability of fluorescent brightness.13
6.10 Water tolerance . 13
6.11 Corrosive properties. 14
6.12 Content of sulfur and halogens (for products designated low in sulfur and halogens) . 17
6.13 Residue on evaporation/solid content. 18
6.14 Penetrant tolerance . 18
6.15 Developer performance. 18
6.16 Redispersability . 18
6.17 Density of carrier liquid. 19
6.18 Product performance (pressurized containers) . 19
6.19 Particle size distribution . 19
6.20 Water content . 19
7 Packaging and labelling. 19
Annex A (normative) Comparison of fluorescent brightness. 20
Annex B (normative) Process control tests . 22
Annex C (informative) Equipment for determination of the visibility of fluorescent indications . 31
Bibliography . 32
ISO 3452-2:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3452-2 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 138, Non-destructive testing, in collaboration with Technical Committee ISO/TC 135, Non-destructive
testing, Subcommittee SC 2, Surface methods, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 3452-2:2000), which has been technically
revised.
ISO 3452 consists of the following parts, under the general title Non-destructive testing — Penetrant testing:
⎯ General principles
⎯ Part 2: Testing of penetrant materials
⎯ Part 3: Reference test blocks
⎯ Part 4: Equipment
iv © ISO 2006 – All rights reserved
INTERNATIONAL STANDARD ISO 3452-2:2006(E)
Non-destructive testing — Penetrant testing —
Part 2:
Testing of penetrant materials
SAFETY PRECAUTIONS — The materials required by this part of ISO 3452 include chemicals which
may be harmful, flammable and/or volatile. All necessary precautions shall be observed. All relevant
International, national and local regulations pertaining to health and safety, environmental
requirements, etc. shall be observed.
1 Scope
This part of ISO 3452 specifies the technical requirements and test procedures for penetrant materials for their
type testing and batch testing. It also details on-site control tests and methods.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 3059, Non-destructive testing — Penetrant testing and magnetic particle testing — Viewing conditions
ISO 3452-3, Non-destructive testing — Penetrant testing — Part 3: Reference test blocks
ISO 12706, Non-destructive testing — Terminology — Terms used in penetrant testing
ISO/IEC 17025, General requirements for the competence of testing and calibration laboratories
EN 571-1, Non-destructive testing — Penetrant testing — Part 1: General principles
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 12706, EN 571-1 an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.