EN 13445-4:2002/A2:2006

Unfired pressure vessels - Part 4: Fabrication

Delete
This document does not give provisions for manufacturing requirements for vessels designed using Design by Analysis - Direct Route (DBA) of Annex B of EN 13445-3:2002.
Modifications to Clause 1, 5.4.4, 6.2, 8.1, 8.2, 9.3.1, 9.4.1, Clause 10 and Annex ZA.

Unbefeuerte Druckbehälter - Teil 4: Herstellung

Streichen:
Dieses Dokument enthält keine Festlegungen für Anforderungen an die Herstellung von Druckbehältern, die nach dem Analytischen Zulässigkeitsnachweis (vorher: direkte Auslegung nach Analyseverfahren (DBA)) nach EN 13445 3:2002, Anhang B, hergestellt werden.

Récipients sous pression non soumis à la flamme - Partie 4: Fabrication

Le présent document ne donne pas de dispositions relatives aux prescriptions de fabrication des récipients conçus en utilisant la Conception par Analyse  Méthode directe (DBA), suivant l'EN 13445-3:2002, Annexe B.

Neogrevane tlačne posode – 4. del: Proizvodnja

General Information

• Status: Withdrawn
• Publication Date: 05-Dec-2006
• Withdrawal Date: 21-Jul-2009
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• Technical Committee: CEN/TC 54 - Unfired pressure vessels
• Drafting Committee: CEN/TC 54 - Unfired pressure vessels
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 22-Jul-2009
• Completion Date: 22-Jul-2009
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 13445-4:2002/A2:2007 - Unfired pressure vessels - Part 4: Fabrication

Relations

• Replaced By: EN 13445-4:2009 - Unfired pressure vessels - Part 4: Fabrication
• Effective Date: 25-Jul-2009
• Amends: EN 13445-4:2002 - Unfired pressure vessels - Part 4: Fabrication
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2007
1HRJUHYDQHWODþQHSRVRGH±GHO3URL]YRGQMD
Unfired pressure vessels - Part 4: Fabrication
Unbefeuerte Druckbehälter - Teil 4: Herstellung
Récipients sous pression non soumis a la flamme - Partie 4: Fabrication
Ta slovenski standard je istoveten z: EN 13445-4:2002/A2:2006
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 13445-4:2002/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2006
ICS 23.020.30
English Version
Unfired pressure vessels - Part 4: Fabrication
Récipients sous pression non soumis à la flamme - Partie Unbefeuerte Druckbehälter - Teil 4: Herstellung
4: Fabrication
This amendment A2 modifies the European Standard EN 13445-4:2002; it was approved by CEN on 21 October 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13445-4:2002/A2:2006: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope.4
5 Manufacturing tolerances.4
6 Weld details.4
6.2 Vessels or parts made of more than one course .4
8 Manufacturing and testing of welds – Production test.4
8.1 General.4
8.2 Reference criteria.4
9 Forming of pressure parts .5
9.3 Forming procedures.5
9.3.1 Cold forming.5
9.4 Heat treatment after forming .5
9.4.1 General.5
10 Post weld heat treatment (PWHT) .6
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of the EU Pressure Equipment Directive (97/23/EC) .7

Foreword
This document (EN 13445-4:2002/A2:2006) has been prepared by Technical Committee CEN/TC 54 “Unfired
pressure vessels”, the secretariat of which is held by BSI.
This Amendment to the European Standard EN 13445-4:2002 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by June 2007, and conflicting national
standards shall be withdrawn at the latest by June 2007.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, B, C or D, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu
...