Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds (ISO 17639:2022)

This document gives recommendations for specimen preparation, test procedures and their main objectives for macroscopic and microscopic examination.

Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen - Makroskopische und mikroskopische Untersuchungen von Schweißnähten (ISO 17639:2022)

Dieses Dokument legt die Verfahren zur Probenvorbereitung, Prüfverfahren und ihre hauptsächlichen Prüfziele für die makroskopische und mikroskopische Untersuchung fest.

Essais destructifs des soudures sur matériaux métalliques - Examens macroscopique et microscopique des assemblages soudés (ISO 17639:2022)

Le présent document spécifie un mode opératoire d'essai et ses principaux objectifs concernant les examens macroscopique et microscopique des assemblages soudés.

Porušitveno preskušanje zvarnih spojev na kovinskih materialih - Makroskopska in mikroskopska preiskava zvarov (ISO 17639:2022)

Ta dokument navaja priporočila za pripravo vzorcev, preskusne postopke in njihove glavne cilje za makroskopsko in mikroskopsko preiskavo.

General Information

Status
Published
Publication Date
15-Feb-2022
Withdrawal Date
30-Aug-2022
Technical Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
16-Feb-2022
Completion Date
16-Feb-2022

Relations

Buy Standard

Standard
EN ISO 17639:2022
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN ISO 17639:2013
Porušitveno preskušanje zvarnih spojev na kovinskih materialih - Makroskopska
in mikroskopska preiskava zvarov (ISO 17639:2022)
Destructive tests on welds in metallic materials - Macroscopic and microscopic
examination of welds (ISO 17639:2022)
Zerstörende Prüfung von Schweißverbindungen an metallischen Werkstoffen -
Makroskopische und mikroskopische Untersuchungen von Schweißnähten (ISO
17639:2022)
Essais destructifs des soudures sur matériaux métalliques - Examens macroscopique et
microscopique des assemblages soudés (ISO 17639:2022)
Ta slovenski standard je istoveten z: EN ISO 17639:2022
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 17639
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2022
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN ISO 17639:2013
English Version
Destructive tests on welds in metallic materials -
Macroscopic and microscopic examination of welds (ISO
17639:2022)
Essais destructifs des soudures sur matériaux Zerstörende Prüfung von Schweißverbindungen an
métalliques - Examens macroscopique et metallischen Werkstoffen - Makroskopische und
microscopique des assemblages soudés (ISO mikroskopische Untersuchungen von Schweißnähten
17639:2022) (ISO 17639:2022)
This European Standard was approved by CEN on 1 February 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17639:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 17639:2022) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2022, and conflicting national standards shall
be withdrawn at the latest by August 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17639:2013.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 17639:2022 has been approved by CEN as EN ISO 17639:2022 without any modification.

INTERNATIONAL ISO
STANDARD 17639
Second edition
2022-01
Destructive tests on welds in metallic
materials — Macroscopic and
microscopic examination of welds
Essais destructifs des soudures sur matériaux métalliques — Examens
macroscopique et microscopique des assemblages soudés
Reference number
ISO 17639:2022(E)
ISO 17639:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 17639:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and abbreviated terms.1
5 Principle . 2
6 Purpose of the test . 2
7 Removal of test specimens . 2
8 Test procedure .3
8.1 General . 3
8.2 Test specimen preparation . 3
8.3 Surface finish . 3
8.4 Etching methods . 4
8.5 Etchants . 4
8.6 Safety measures . 4
9 Examination . 4
10 Designation . 4
11 Test report . 7
Annex A (informative) Example of a test report. 8
Bibliography . 9
iii
ISO 17639:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 5, Testing and inspection of welds, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 121, Welding and allied processes, in accordance
with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 17639:2003), which has been technically
revised.
The main changes are as follows:
— Clause 2 has been updated;
— the designations according to ISO/TR 15608 have been updated in Clause 10.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page:
https://committee.iso.org/sites/tc44/home/interpretation.html.
iv
INTERNATIONAL STANDARD ISO 17639:2022(E)
Destructive tests on welds in metallic materials —
Macroscopic and microscopic examination of welds
1 Scope
This document gives recommendations for specimen preparation, test procedures and their main
objectives for macroscopic and microscopic examination.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 6520-1, Welding and allied processes — Classification of geometric imperfections in metallic materials
— Part 1: Fusion welding
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
macroscop
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.