EN 14680:2006
(Main)Adhesives for non-pressure thermoplastic piping systems - Specifications
Adhesives for non-pressure thermoplastic piping systems - Specifications
This European Standard specifies the requirements and test methods for adhesives used for joining the components of unplasticised poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride)(PVC-C), acrylonitrile -butadiene-styrene (ABS) and styrene copoly¬mer blends (PVC+SA¬N) thermoplastic piping systems for fluids under zero pressure (e.g. soil and waste discharge), independent of the application area.
It provides reference for the evaluation of conformity of the adhesive to this EN.
Klebstoffe für drucklose thermoplastische Rohrleitungssysteme - Festlegungen
Diese Europäische Norm legt die Anforderungen an und Prüfverfahren für Klebstoffe fest, die zum Verbinden
der Bauteile von thermoplastischen Rohrleitungssystemen aus weichmacherfreiem Polyvinylchlorid (PVC-U),
chloriertem Polyvinylchlorid (PVC-C), Acrylnitril-Butadien-Styrol (ABS) und Styrol-Copolymer-Blends (PVC+SAN)
für Flüssigkeiten verwendet werden, die sich nicht unter Druck befinden (z. B. Ableitung von Abwasser),
unabhängig vom Anwendungsbereich.
Sie schreibt die Bewertung der Konformität des Klebstoffes mit dieser EN vor.
Adhésifs pour systèmes de canalisations thermoplastiques sans pression - Spécifications
La présente norme européenne spécifie les exigences et les méthodes d’essai applicables aux adhésifs
utilisés pour assembler les composants de systèmes de canalisations thermoplastiques constituées de
poly(chlorure de vinyle) non plastifié (PVC-U), de poly(chlorure de vinyle) chloré (PVC-C), d’acrylonitrile-butadiène-
styrène (ABS) et de mélanges de copolymères de styrène (PVC+SAN), pour des liquides sans
pression (des eaux-vannes et des eaux usées, par exemple), quelle que soit la zone d’application.
Une référence est fournie pour évaluer la conformité de l’adhésif à la présente norme européenne.
Lepila za netlačne plastomerne cevne sisteme - Specifikacije
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Adhesives for non-pressure thermoplastic piping systems - SpecificationsAdhésifs pour systemes de canalisations thermoplastiques sans pression - SpécificationsKlebstoffe für drucklose thermoplastische Rohrleitungssysteme - FestlegungenTa slovenski standard je istoveten z:EN 14680:2006SIST EN 14680:2007en83.180LepilaAdhesivesICS:SLOVENSKI
STANDARDSIST EN 14680:200701-april-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14680October 2006ICS 83.180 English VersionAdhesives for non-pressure thermoplastic piping systems -SpecificationsAdhésifs pour systèmes de canalisations thermoplastiquessans pression - SpécificationsKlebstoffe für drucklose thermoplastischeRohrleitungssysteme - FestlegungenThis European Standard was approved by CEN on 4 September 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14680:2006: E
Possible characterization test methods for adhesives for thermoplastic piping systems.14 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive.15 ZA.1
Scope and relevant characteristics.15 ZA.2
Procedure(s) for the attestation of conformity of adhesives for non-pressure thermoplastic piping systems.16 ZA.3
CE Marking.17 Bibliography.19
Introduction This product standard contains the requirements for adhesives for non-pressure thermoplastic piping systems independent of piping system application. The existing system and application standards which specify parameters for adhesive joints in particular application areas and the test methods specified therein remain unchanged. The requirements referred to in these system standards concern temperature, pressure and standard life span of the piping system, and are applicable to all the components of the piping system for all the relevant dimensions that require specified application. This product standard completes the characterisation of the adhesives for thermoplastic piping systems in conjunction with another product standard prEN 14814 "Adhesives for thermoplastic piping systems for fluids under pressure - Specifications". These product standards are supported by standard test methods to which references are made through the texts.
1 Scope This European Standard specifies the requirements and test methods for adhesives used for joining the components of unplasticised poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride)(PVC-C), acrylonitrile -butadiene-styrene (ABS) and styrene copolymer blends (PVC+SAN) thermoplastic piping systems for fluids under zero pressure (e.g. soil and waste discharge), independent of the application area. It provides reference for the evaluation of conformity of the adhesive to this EN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 923:2005, Adhesives - Terms and definitions EN 1055, Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling EN 1329 (all parts), Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure -Unplasticized poly(vinyl chloride) (PVC-U) EN 1455 (all parts), Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) EN 1565 (all parts), Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) EN 1566 (all parts), Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) EN 13566-1:2002, Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General EN 45020:1998, Standardization and related activities - General vocabulary (ISO/IEC Guide 2:1996) EN ISO 9001:2000, Quality management systems - Requirements (ISO 9001:2000) prEN ISO 9229:2004, Thermal insulation - Definitions of terms (ISO/DIS 9229:2004) EN ISO 9311-1, Adhesives for thermoplastic piping systems - Part 1: Determination of film properties (ISO 9311-1:2005)
EN ISO 9311-2, Adhesives for thermoplastic piping systems – Part 2: Determination of shear strength (ISO 9311-2:2002) CEN ISO/TS 15874-7:2003, Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 7: Guidance for the assessment of conformity (ISO/TS 15874-7:2003)
NOTE This clause applies for assessment of conformity if third party certification is involved 3.2.1 conformity assessment [EN 45020:1998] any activity concerned with determining directly or indirectly that relevant requirements are fulfilled
3.2.2 Batch Release Test (BRT) [EN 13566-1:2002] test performed by the manufacturer on a batch of components, which has to be satisfactorily completed before the batch can be released
3.2.3 Type Test (TT) [CEN ISO/TS 15874-7:2003] tests performed to prove that the material, component, joint or assembly is capable of conforming with the relevant requirements given in the System Standard 3.2.4 Initial Type Test (ITT) [prEN ISO 9229:2004] one or more tests performed on a product prior to commencing normal production to prove that the product is capable of conforming to the relevant requirements of this standard 4 Requirements 4.1 General considerations 4.1.1 The manufacturer of the adhesive shall specify for which non-pressure system (EN 1329 (PVC-U), EN 1455 (ABS), EN 1566 (PVC-C), EN 1565 (SAN+PVC)) the adhesive is intended. 4.1.2 When not otherwise mentioned, the test pieces shall fulfil the following requirements set in Tables 1 and 2:
Table 1 — Test pieces diametral clearance
PVC-U
−1,006,0mm
PVC-C
−1,006,0mm
ABS
−1,006,0mm
SAN+PVC
−1,006,0mm
Table 2 — Test pieces setting time
Setting time
Setting conditions
PVC-U
1 h 1 day 20 days
At (23 ± 2)ºC and (50 ± 5) % relative humidity
PVC-C
1 h 1 day 20 days
At (23 ± 2)ºC and (50 ± 5) % relative humidity
ABS
1 h 1 day 20 days
At (23 ± 2)ºC and (50 ± 5) % relative humidity
SAN + PVC
1 h 1 day 20 days
At (23 ± 2) ºC and (50 ± 5) % relative humidity
The setting time shall be measured from the start of the application of the adhesive.
Table 3 — Requirements for the shear strength
Test temperature (ºC)
Setting time (hours)
PVC-U
adhesives MPa (N/mm2)
PVC-C adhesives MPa (N/mm2)
ABS adhesives (SAN+PVC) adhe-sives MPa (N/mm2)
23 ± 2
≥ 0,25
≥ 0,25
≥ 0,10
23 ± 2
≥ 1,5
≥ 1,5
≥ 1,5
23 ± 2
≥ 3,0
≥ 3,0
≥ 3,0
4.3 Resistance to elevated temperature cycling The adhesive joints shall be prepared according to the instructions recommended by the adhesive manufacturer. The setting time of the adhesive joints shall be at least 24 h at (23 ± 2) ºC and (50 ± 5) % relative humidity. The adhesive shall be tested in accordance with EN 1055 application "B" using pipe and fitting compatible with the claims of the adhesive suitability.
The test assembly, application B, described in EN 1055, shall contain a minimum of six adhesive joints: minimum two adhesive joints in pipe of 40 mm or 50 mm diameter, horizontal stack.
minimum two adhesive joints in pipe of 75 mm ≤ d ≤ 160 mm diameter, vertical stack. minimum two adhesive joints in pipe of 75 mm ≤ d ≤ 160 mm diameter, horizontal stack. When tested in accordance with this method, each adhesive joint shall show no signs of leakage.
4.4 Shelf life
The producer shall recheck the film properties (see Annex A) and the shear strength (setting time 24 h) of the adhesive after the recommended shelf life (minimum 12 months). The adhesive, stored in unopened containers in accordance with the manufacturer's instructions for the specified shelf life shall still meet the requirements of Table 3.
- factory production control by the manufacturer, including product assessment - batch release test 5.2 Initial type testing 5.2.1 General Initial type testing shall be performed at the beginning of the production of a new adhesive for thermoplastic piping systems or at the beginning of a new method of production or raw material supplier (where this may affect the stated properties). Historical data may be used insofar as tests previously performed on the same adhesive in accordance with the provisions of this standard (same characteristic(s), test method, sampling procedure, system
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.