iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 14541-1:2022

(Main)

Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary

Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary

This document specifies the general terms and definitions relevant for the utilization of thermoplastics recyclates in thermoplastics pipes, fittings and ancillaries for both pressure and non-pressure piping systems.
This document is intended to be used by specification writers in conjunction with CEN/TS 14541-2 when preparing normative documents under the scope of CEN/TC 155.

Kunststoff-Rohrleitungen und -Formstücke - Verwendung von thermoplastischen Rezyklaten - Teil 1: Begriffe

Dieses Dokument legt allgemeine Begriffe fest, die bei der Verwendung von thermoplastischen Rezykla¬ten in thermoplastischen Rohrleitungen, Formstücken und Zubehörteilen sowohl in druckbeaufschlagten als auch in drucklosen Rohrleitungssystemen von Bedeutung sind.
Die Verwendung dieses Dokument ist in Verbindung mit CEN/TS 14541-2 bei der Erarbeitung von normativen Dokumen¬ten innerhalb des Geltungsbereiches von CEN/TC 155 zur Nutzung durch Verfasser von Spezifikationen vorgesehen.

Tubes et raccords en plastique - Utilisation de recyclats thermoplastiques - Partie 1 : Vocabulaire

Le présent document spécifie les termes généraux et définitions pertinents pour l'utilisation des recyclats thermoplastiques dans les tubes, les raccords et les accessoires en thermoplastique pour les systèmes de canalisations sous pression et sans pression.
Le présent document est destiné à être utilisé par les rédacteurs de spécifications conjointement avec la CEN/TS 14541-2 lors de la préparation de documents normatifs dans le domaine d'application du CEN/TC 155.

Polimerne cevi in fitingi - Uporaba recikliranih plastomerov - 1. del: Terminologija

Ta dokument določa splošne izraze in definicije, ki se navezujejo na uporabo recikliranih plastomerov v plastomernih ceveh, fitingih ter pomožnih delih pri tlačnih in netlačnih cevnih sistemih.
Ta dokument naj bi uporabljali avtorji specifikacij v povezavi s standardoma prCEN/TR 14541-2 in prCEN/TR 14541-3 pri sestavljanju normativnih dokumentov, ki spadajo na področje uporabe standarda CEN/TC 155.

General Information

Status
Published
Publication Date
03-May-2022
Withdrawal Date
29-Nov-2022
ICS
83.140.30 - Plastics pipes and fittings for non fluid use
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 25 - Recycling of PVC-U, PE and PP materials
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
04-May-2022
Due Date
27-Dec-2022
Completion Date
04-May-2022
Ref Project
SIST EN 14541-1:2022 - Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary

Relations

Replaces
CEN/TS 14541:2013 - Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE materials
Effective Date
08-Jun-2022

Buy Standard

EN 14541-1:2022EN 14541-1:2022
PreviousNext
Standard
EN 14541-1:2022
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 14541-1:2022
01-julij-2022
Nadomešča:
SIST-TS CEN/TS 14541:2013
Polimerne cevi in fitingi - Uporaba recikliranih plastomerov - 1. del: Terminologija
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 1: Vocabulary
Kunststoff-Rohrleitungen und -Formstücke - Verwendung von thermoplastischen
Rezyklaten - Teil 1: Begriffe
Tubes et raccords en plastique - Utilisation de recyclats thermoplastiques - Partie 1 :
Vocabulaire
Ta slovenski standard je istoveten z: EN 14541-1:2022
ICS:
01.040.23 Tekočinski sistemi in sestavni Fluid systems and
deli za splošno rabo (Slovarji) components for general use
(Vocabularies)
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST EN 14541-1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 14541-1:2022

---------------------- Page: 2 ----------------------
SIST EN 14541-1:2022


EN 14541-1
EUROPEAN STANDARD

NORME EUROPÉENNE

May 2022
EUROPÄISCHE NORM
ICS 83.140.30 Supersedes CEN/TS 14541:2013
English Version

Plastics pipes and fittings - Utilisation of thermoplastics
recyclates - Part 1: Vocabulary
Tubes et raccords en plastique - Utilisation de recyclats Kunststoff-Rohrleitungen und -Formstücke -
thermoplastiques - Partie 1 : Vocabulaire Verwendung von thermoplastischen Rezyklaten - Teil
1: Begriffe
This European Standard was approved by CEN on 7 February 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14541-1:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 14541-1:2022
EN 14541-1:2022 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Abbreviations . 8
Bibliography . 9
2

---------------------- Page: 4 ----------------------
SIST EN 14541-1:2022
EN 14541-1:2022 (E)
European foreword
This document (EN 14541-1:2022) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2022, and conflicting national standards shall
be withdrawn at the latest by November 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. C
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 16486-1:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General (ISO 16486-1:2023)
SIST EN ISO 16486-1:2024

This document specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
This document establishes a calculation and design scheme on which to base the maximum operating pressure (MOP) of a PA-U piping system.
NOTE            For the purpose of this document the term gaseous fuels includes, for example, natural gas, methane, butane, propane, hydrogen, manufactured gas, biogas, and mixtures of these gases.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN ISO/TS 16486-7:2023(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 7: Assessment of conformity (ISO/TS 16486-7:2023)
SIST-TS CEN ISO/TS 16486-7:2023

This document gives guidance and requirements for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of the ISO 16486 series which are intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1    A basic test matrix in Annex B provides an overview of the testing scheme.
It is recommended for the manufacturer to have a management system such as ISO 9001[4] or equivalent.
NOTE 2    If certification is involved, certification bodies and inspection bodies operating according to ISO/IEC 17065 and ISO/IEC 17020 are considered to be competent.
In conjunction with the other parts of the ISO 16486 series (see Clause 2), this document is applicable to unplasticized polyamide (PA-U) piping systems intended to be buried and used for the supply of gaseous fuels. It is applicable to PA-U pipes, fittings and valves, as well as to their joints and to joints with components of other materials intended to be used under the following conditions:
a)    a maximum operating pressure (MOP) up to and including 18 bar[1] (the MOP is limited to 16 bar for CEN member countries, where ISO 16486-6 is replaced by CEN/TS 12007-6[1]);
b)    an operating temperature of 20 °C as the reference temperature.
NOTE 3    For operating temperatures different to 20 °C, derating coefficients can be used (see ISO 16486-6). CEN member countries use CEN/TS 12007-6[1] and ISO/TS 16486-7 (this document) as a basis, but they can also request additional requirements. For non-CEN member countries, information for dealing with special cases for PA-U can be found in ISO/TS 16486-7 (this document) and PPI TR-3.[7]
For mechanical fittings conforming to ISO 17885, guidance for assessment of conformity is not given in this document. When requested, a quality plan based on the tests mentioned can be set up in agreement between user and manufacturer.
The ISO 16486 series covers a range of maximum operating pressures and gives requirements concerning colours.
NOTE 4    It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm2.

  • Technical specification
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 14541-2:2022(Main)
Plastics pipes and fittings - Utilisation of thermoplastics recyclates - Part 2: Recommendations for relevant characteristics
SIST-TS CEN/TS 14541-2:2022

This document provides guidance and information for drafting product standards to specify characteristics and test methods for the utilization of thermoplastics recyclates (PVC-U, PVC-C, PE, PP, ABS) in pipes, fittings and ancillaries for thermoplastics piping systems.
This document covers recyclates with an agreed specification from all sources.
NOTE 1   This document does not cover characteristics for reworked material.
NOTE 2   This document does not cover recycling processes (e.g. chemical or mechanical).
NOTE 3   This document does not define if recycled material can be used in a specific application. The possible use of recyclates will be defined in the applicable product standard.
This document provides guidance about the relevant characteristics to be included in the agreed specification for recyclates.
This document is applicable without prejudice to any existing legislation.
For the recycling process, the transport, the testing and the use of thermoplastics recyclates, National and/or European regulations (e.g. hygienic aspects) can apply.
NOTE 4   For example, threshold levels for substances of very high concern (SVHC) as defined in the REACH-legislation which can possibly be present in thermoplastic recyclates.

  • Technical specification
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-4:2022(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 4: Valves (ISO 16486-4:2022)
SIST EN ISO 16486-4:2022

This document specifies the characteristics of valves made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels.
It is applicable to isolating unidirectional and bi-directional valves with spigot ends or electrofusion sockets intended to be fused with PA-U pipes or fittings conforming to ISO 16486-2 and ISO 16486-3 respectively.
Valves made from material other than unplasticized polyamide designed for the supply of gaseous fuels conforming to the relevant standards are permitted to be used in PA-U piping systems according to the ISO 16486 series provided they have relevant PA-U connections for butt fusion or electrofusion ends (see ISO 16486-3). The component, i.e. the complete valve, is required to fulfil the requirements of this document.
This document also specifies the test parameters for the test methods it describes.
In conjunction with ISO 16486-1, ISO 16486-2, ISO 16486-3 and ISO 16486-5, this document is applicable to PA-U valves and their joints and to joints with components of PA-U and other materials intended to be used under the following conditions:
a) a maximum operating pressure (MOP) of up to and including 18 bar[1], or limited to 16 bar under regional CEN requirements, at a reference temperature of 20 °C for design purposes;
NOTE 1    For the purpose of this document and the references to ISO 8233, MOP is considered to be nominal pressure.
b) an operating temperature of −20 °C to 40 °C;
NOTE 2    For operating temperatures between 20 °C and 40 °C, derating coefficients are specified in ISO 16486-5.
This document covers valves for pipes with a nominal outside diameter, dn, ≤ 400 mm.
[1] 1 bar = 0,1 MPa = 105 Pa; 1 MPa = 1 N/mm².

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-5:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system (ISO 16486-5:2021)
SIST EN ISO 16486-5:2021

This document specifies the requirements of fitness for purpose of unplasticized polyamide (PA-U) piping system, intended to be buried and used for the supply of gaseous fuels. It also specifies the definitions of electrofusion and butt fusion joints.
This document specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints and to joints with components of PA-U.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-2:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2020)
SIST EN ISO 16486-2:2020

This document specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series of standards is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, this document lays down dimensional characteristics and requirements for the marking of pipes.
Pipes conforming to this document are jointed typically by using mechanical, electrofusion or butt fusion techniques.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16486-3:2020(Main)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO 16486-3:2020)
SIST EN ISO 16486-3:2020

This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486‑1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirements for the marking of fittings.
In conjunction with the other parts of the ISO 16486 series, this document is applicable to PA-U fittings, their joints, joints with components of PA-U and joints with mechanical fittings of other materials, and to the following fitting types:
—     fusion fittings (electrofusion fittings and butt fusion fittings), and
—     transition fittings.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 9080:2012(Main)
Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)
SIST EN ISO 9080:2012

ISO 9080:2012 specifies a method for predicting the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation. The method is applicable to all types of thermoplastics pipe at applicable temperatures. It was developed on the basis of test data from pipe systems.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 852:2010(Main)
Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values
SIST-TP CEN/TR 852:2011

This Technical Report is applicable to plastics pipes, joints and fittings to be used for the transport of water intended for human consumption and raw water used for the manufacture of water intended for human consumption.
It gives guidance on:
a)   the number of successive migration periods to be carried out;
b)   how to interpret M values calculated from successive migration periods;
c)   a method for converting M values into values that reflect field use conditions;
d)   acceptance criteria for the duplicate M values obtained by testing in accordance with EN ISO 8795.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1905:1998(Main)
Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content
SIST EN 1905:2000

This standard specifies a method for assessing the poly(vinyl chloride) (PVC) content in reprocessable and recyclable unplasticized (PVC-U) materials or materials derived from PVC-U products. In this standard, only the method for calculation of the PVC content is described, while for the determination of the chlorine content reference is made to prEN ISO 1158:1997. If the material contains or is supposed to contain chlorinated poly(vinyl chloride) (PVC-C) or chlorinated polyethylene (PE-C), an apparent PVC content is calculated.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day