EN ISO 60:1999

Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977)

Specifies a method for the determination of the apparent density of a moulding powder or a granular material. The sample is pured through a specified funnel into a measuring cylinder of 100 cubiccentimeter capacity, the excess is removed with a straightedge and the mass of the contents is determinded by weighing. Expression of the apparent density in grams per millilitre.

Kunststoffe - Bestimmung der scheinbaren Dichte von Formmassen, die durch einen genormten Trichter abfließen können (Schüttdichte) (ISO 60:1977)

Die vorliegende Internationale Norm legt ein Verfahren zur Bestimmung der Schüttdichte, d.h. der Masse pro Volumeneinheit von Formmassen aus Pulvern oder Körnern, die durch einen gegebenen Trichter abfließen können, fest.

Plastiques - Détermination de la masse volumique apparente des matières susceptibles de s'écouler à travers un entonnoir donné (ISO 60:1977)

La présente Norme internationale spécifie une méthode de détermination de la masse volumique apparente, c'est-à-dire la masse par unité de volume, des matières en poudre ou en granulés, susceptibles de s'écouler à travers un entonnoir d'un modèle déterminé.  
NOTE - Pour une méthode de détermination de la masse volumIque apparente des matières à mouler non susceptibles de s'écouler à travers un entonnoir donné, voir ISO 61.  Lorsque cette méthode est appliquée à des matières composées de grains relativement gros, des résultats variables peuvent être obtenus, dus à l'erreur introduite lorsque le sommet du cylindre est arasé avec une lame à bord rectiligne.  La connaissance de la masse volumique apparente ne peut servir à comparer l'expansion ou le foisonnement de matières à mouler que si leur densité à l'état moulé est approximativement la même.

Polimerni materiali - Določanje nasipne mase materiala, ki se lahko nasipa skozi lij določenih mer (ISO 60:1977)

General Information

• Status: Withdrawn
• Publication Date: 18-May-1999
• Withdrawal Date: 03-Oct-2023
• ICS: 83.080.01 - Plastics in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249/SC 1/WG 13 - Thermosets
• Ref Project: SIST EN ISO 60:2000 - Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:1977)

Relations

• Replaced By: EN ISO 60:2023 - Plastics - Determination of apparent density of material that can be poured from a specified funnel (ISO 60:2023)
• Effective Date: 12-Oct-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2000
3ROLPHUQLPDWHULDOL'RORþDQMHQDVLSQHPDVHPDWHULDODNLVHODKNRQDVLSDVNR]LOLM
GRORþHQLKPHU,62
Plastics - Determination of apparent density of material that can be poured from a
specified funnel (ISO 60:1977)
Kunststoffe - Bestimmung der scheinbaren Dichte von Formmassen, die durch einen
genormten Trichter abfließen können (Schüttdichte) (ISO 60:1977)
Plastiques - Détermination de la masse volumique apparente des matieres susceptibles
de s'écouler a travers un entonnoir donné (ISO 60:1977)
Ta slovenski standard je istoveten z: EN ISO 60:1999
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
83.080.10 Duromeri Thermosetting materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION l MEXflYHAPOAHAR OPl-AHM3AUMfl l-Io CTAHAAPTM3AUM~.ORGANISATION INTERNATIONALE DE NORMALISATION
Determination of apparent density of material that
Plastics -
tan be poured from a specified funnel
Plastiques - Determination de la masse volumique apparente des matEres susceptibles de s ’ecouler a travers un
en tonnoir donnk
Second edition - 1977-08-01
UDC 678.033 : 531.755 Ref. No. ISO 60-1977 (E)
c
Y
Descriptors : plastics, moulding materials, tests,s physical tests,, density measurement, bulk density .
s
Price based-on 2 pages
ßOREWORD
ISO (the International Organization for Standardization) is a worldwide federation
of national Standards institutes (EO member bodies). The work of developing
International Standards is carried out through SS0 technical committees. Every
member body interested in a subject for which a technical committee has been set
up has the right to be represented on that committee. lnternational organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work.
Draft International Standards adopted by the technical committees are circulated
to the member bodies for approval before their acceptance as International
Standards by the ISO Council.
ISO 60 was developed by Technical Committee
International Standard
ISO/TC 6 1, Plastics.
This second edition was submitted directly to the ISO Council, in accordance
with clause 6.12.1 of the Directives for the technical work of ISO. lt cancels
and replaces the first edition (i.e. ISO 60- ‘l976), which had been approved by the
member bodies of the following countries :
Australia India Portugal
Austria I reland South Africa, Rep. of
Belgium Israel Spain
Chile I taly Sweden
Czechoslovakia Japan Turkey
Denmark Mexico United Kingdom
Finland Netherlands U.S.A.
France New Zealand U.S.S. R.
Germany Pakistan Yugoslavia
G reece
Poland
No member body had expressed disapproval of the document.
0 International Organkation for Standardkation, 1977 l
Printed in Switzerlan
...