EN 13880-10:2018

Hot applied joint sealants - Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression

This document specifies a method for determination of adhesion and cohesion characteristics of hot applied joint sealant specimens following cyclic extensions.
NOTE   The test simulates yearly joint movements due to temperature variations.

Heiß verarbeitbare Fugenmassen - Teil 10: Prüfverfahren zur Bestimmung des Dehn- und Haftvermögens bei kontinuierlicher Dehnung und Stauchung

Dieses Dokument legt ein Verfahren zur Bestimmung des Adhäsions- und Kohäsionsverhaltens von Probekörpern heiß verarbeitbarer Fugenmassen durch zyklische Dehnung.
ANMERKUNG   Die Prüfung simuliert jährliche Fugenbewegungen durch Temperaturschwankungen.

Produits de scellement de joints appliqués à chaud - Partie 10 : Méthode d'essai pour la détermination de l'adhésion et de la cohésion après traction et compression répétée

Ce document décrit une méthode pour la détermination des caractéristiques d’adhésion et de cohésion d’éprouvettes de produit de scellement de joint appliqué à chaud après des cycles de traction répétée.
NOTE   L'essai simule les mouvements annuels du joint dus aux variations de température.

Tesnilne mase za stike, ki se vgrajujejo po vročem postopku - 10. del: Preskusna metoda za ugotavljanje adhezije in kohezije po dolgotrajnem raztezanju in stiskanju

Ta evropski standard opisuje metodo za ugotavljanje značilnosti adhezije in kohezije vzorcev tesnilnih mas za stike, ki se vgrajujejo po vročem postopku, po preskušanju vezave z dolgotrajnim raztezanjem in stiskanjem.

General Information

• Status: Published
• Publication Date: 29-May-2018
• Withdrawal Date: 29-Nov-2018
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 227 - Road materials
• Drafting Committee: CEN/TC 227/WG 3 - Materials for concrete roads including joint fillers and sealants
• Current Stage: 9060 - Closure of 2 Year Review Enquiry - Review Enquiry
• Start Date: 02-Dec-2023
• Completion Date: 02-Dec-2023
• Ref Project: SIST EN 13880-10:2018 - Hot applied joint sealants - Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression

Relations

• Replaces: EN 13880-10:2003 - Hot applied joint sealants - Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression
• Effective Date: 06-Jun-2018

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.VWLVNDQMXHeiß verarbeitbare Fugenmassen - Teil 10: Prüfverfahren zur Bestimmung des Dehn- und Haftvermögens bei kontinuierlicher Dehnung und StauchungProduits de scellement de joints appliqués à chaud - Partie 10: Méthode d'essai pour la détermination de l'adhésion et de la cohésion après traction et compression répétéeHot applied joint sealants - Part 10: Test method for the determination of adhesion and cohesion following continuous extension and compression93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 13880-10:2018SIST EN 13880-10:2018en,fr,de01-september-2018SIST EN 13880-10:2018SLOVENSKI
STANDARDSIST EN 13880-10:20041DGRPHãþD



SIST EN 13880-10:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13880-10
May
t r s z ICS
{ uä r z rä t r Supersedes EN
s u z z ræ s rã t r r uEnglish Version
Hot applied joint sealants æ Part
s rã Test method for the determination of adhesion and cohesion following continuous extension and compression Produits de scellement de joints appliqués à chaud æ Partie
s rã Méthode d 5essai pour la détermination de l 5adhésion et de la cohésion après traction et compression répétée
Heiß verarbeitbare Fugenmassen æ Teil
s rã Prüfverfahren zur Bestimmung des Dehnæ und Haftvermögens bei kontinuierlicher Dehnung und Stauchung This European Standard was approved by CEN on
s x March
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u z z ræ s rã t r s z ESIST EN 13880-10:2018



EN 13880-10:2018 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Principle . 4 5 Apparatus . 4 5.1 Jig for pouring and handling of test specimen . 4 5.2 Tensile rig . 5 5.3 Cooling chamber . 5 5.4 Measurement of forces . 5 5.5 Ruler . 5 6 Preparation and conditioning of test specimens . 5 7 Procedure. 6 8 Calculation and expression of results
...