EN 12629-2:2002+A1:2010
(Main)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
This part of EN 12629, taken together with EN 12629-1:2000+A1, applies to machines for the manufacture of blocks, kerbs, paving stones and similar concrete products.
EN 12629-1:2000+A1 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium silicate.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1 specific to the machines it covers.
1.2 This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards.
1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1-2 of annex B) and the point where the pallet boards are brought to the assembly (see point 3 of annex B) until the point where the green products are removed from the machine assembly to the curing system (see point 4 of annex B).
1.4 This European Standard deals with the hazards listed in clause 4 which can arise during the operation and maintenance, including the interfaces, of the block making machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative.
NOTE 1 Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration.
NOTE 2 Interfaces between the block making machines and others of the installation are dealt with in
EN 12629-1:2000+A1:2010 (7.2).
This standard establishes safety requirements and/or methods of protection which apply to these machines.
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen
Dieser Teil von EN 12629, zusammen mit EN 12629-1:2000+A1:2010, gilt für Maschinen zur
Herstellung von Blöcken, Bordsteinen, Pflastersteinen und ähnlichen Betonprodukten.
EN 12629-1:2000+A1:2010 spezifiziert allgemeine Anforderungen für Maschinen zur Herstellung von Bauprodukten
aus Beton und Kalksandstein.
Dieses Dokument legt die zusätzlichen Anforderungen für und/oder Abweichungen von
EN 12629-1:2000+A1:2010, die spezifisch für die Maschinen sind, die es abdeckt, fest."
1.2 !Diese Europäische Norm behandelt alle signifikanten Gefährdungen, die auf diese Maschinen
zutreffen, wenn sie bestimmungsgemäß und unter den Bedingungen des Missbrauchs, die vernünftigerweise
vom Hersteller vorhersehbar sind, verwendet werden (siehe Abschnitt 4). Diese Europäische Norm spezifiziert
die entsprechenden technischen Maßnahmen zur Beseitigung oder Verminderung der Risiken, die von den
signifikanten Gefährdungen ausgehen."
1.3 Diese Norm gilt für die Maschine von der Stelle an, wo die Mischzufuhr die Maschine befüllt (siehe
Punkt 1 bis 2 von Anhang B) und an der Stelle, wo die Unterlagsbretter zugeführt werden (siehe Punkt 3 von
Anhang B) bis zu der Stelle, wo die Frischprodukte zu dem „Trockenkammer-System“ (siehe Punkt 4 von
Anhang B) abtransportiert werden.
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocs
La présente partie de l’EN 12629, utilisée avec l’EN 12629-1:2000+A1, s’applique aux machines pour la
fabrication de blocs, bordures de trottoirs, pavés et autres produits similaires en béton.
L’EN 12629-1:2000+A1 spécifie les prescriptions générales applicables aux machines pour la fabrication de produits
de construction en béton et silico-calcaire.
Le présent document spécifie les prescriptions supplémentaires et les dérogations à l’EN 12629-1:2000+A1
spécifiques aux machines concernées."
1.2 !La présente Norme européenne traite tous les phénomènes dangereux significatifs spécifiques
à ces machines, lorsque celles-ci sont utilisées normalement et dans des conditions de mauvais usage que le
fabricant peut raisonnablement prévoir (voir l’Article 4). Cette Norme européenne spécifie les mesures techniques
appropriées pour éliminer ou réduire les risques dus aux phénomènes dangereux significatifs."
1.3 La présente Norme européenne s’applique aux machines, du point où le mélange pénètre dans la machine
(voir points 1 et 2 de l’annexe B) et du point où les palettes sont introduites dans la machine (voir point 3 de
l’annexe B) jusqu’au point où les produits frais sont transférés de la machine au système de cure (voir point 4 de
l’annexe B).
Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 2. del: Stroji za izdelavo blokov
Ta del EN 12629 skupaj z EN 12629-1:2000+A1:2010 velja za stroje za izdelavo blokov, robnikov, tlakovcev in podobnih proizvodov iz betona. EN 12629-1:2000+A1:2010 določa splošne zahteve, ki veljajo za stroje za izdelavo gradbenih proizvodov iz betona in apnenega peščenca. Ta dokument določa dodatne zahteve in/ali odstopanja od EN 12629-1:2000+A1:2010, specifične za stroje, ki jih zajema. Ta evropski standard obravnava vse pomembne nevarnosti, nevarne situacije in primere, ki se nanašajo na te stroje, kadar se uporabljajo kot predvideno in pod pogoji napačne uporabe, ki jih razumno predvidi proizvajalec (glej Klavzulo 4). Ta evropski standard določa primerne tehnične ukrepe za odpravo ali zmanjšanje tveganj, ki se pojavijo zaradi pomembnih nevarnosti. Ta evropski standard velja za stroje od točke, na kateri zmes vstopa v stroj (glej točki 1 in 2 Dodatka B) in točke, na kateri paletne plošče prihajajo v montažo (glej točko 3 Dodatka B), do točke, na kateri gredo zeleni proizvodi iz strojnega sklopa v sušilni sistem (glej točko 4 Dodatka B). Ta evropski standard obravnava nevarnosti, navedene v Klavzuli 4, do katerih lahko pride med obratovanjem in vzdrževanjem strojev za izdelavo blokov, vključno z vmesniki, kadar se izvajata v skladu s specifikacijami, ki jih je navedel proizvajalec ali njegov pooblaščeni zastopnik. Ta standard vzpostavlja varnostne zahteve in/ali zaščitne metode, ki veljajo za te stroje.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: SteinformmaschinenMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocsMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-2:2002+A1:2010SIST EN 12629-2:2004+A1:2010en,fr01-december-2010SIST EN 12629-2:2004+A1:2010SLOVENSKI
STANDARD
SIST EN 12629-2:2004+A1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12629-2:2002+A1
September 2010 ICS 91.220 Supersedes EN 12629-2:2002English Version
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocs
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen This European Standard was approved by CEN on 1 November 2002 and includes Amendment 1 approved by CEN on 5 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-2:2002+A1:2010: ESIST EN 12629-2:2004+A1:2010
EN 12629-2:2002+A1:2010 (E) 2 Contents page Foreword . 3Introduction . 41Scope . 42Normative references . 53Terms and definitions . 54List of significant hazards . 64.1Mechanical hazards (see informative annex B) . 64.2Electrical hazards . 84.3Hazards generated by vibration . 85!!!!Safety requirements and/or protective measures"""" . 86!!!!Verification of safety requirements and/or protective measures"""" . 97Information for use . 98Marking . 10Annex A (informative)
Mechanical hazards zones for a common block making machine and requirements and measures . 11Annex
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.