SIST EN 12629-2:2004+A1:2010
(Main)Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for the manufacture of blocks, kerbs, paving stones and similar concrete products. EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium-silicate. This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers. This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards. This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1-2 of annex B) and the point where the pallet boards are brought to the assembly (see point 3 of annex B) until the point where the green products are removed from the machine assembly to the curing system (see point 4 of annex B). This European Standard deals with the hazards deleted text listed in clause 4 which can arise during the operation and maintenance, including the interfaces, of the block making machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. This standard establishes safety requirements and/or methods of protection which apply to these machines.
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen
1.1 Diese Norm gilt für Maschinen zur Herstellung von Blöcken, Bordsteinen, Pflastersteinen und ähnlichen Betonprodukten.
1.2 Diese Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungs-ereignisse, die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Empfehlungen des Herstellers verwendet werden (siehe Abschnitt 4). Diese Norm spezifiziert die entsprechenden technischen Maßnahmen zur Beseitigung oder Verminderung der Risiken, die von diesen Gefährdungen ausgehen.
1.3 Diese Norm gilt für die Maschine von der Stelle an, wo die Mischzufuhr die Maschine befüllt (siehe Punkt 1 bis 2 von Anhang B) und an der Stelle, wo die Unterlagsbretter zugeführt werden (siehe Punkt 3 von Anhang B) bis zu der Stelle, wo die Frischprodukte zu dem "Trockenkammer-System" (siehe Punkt 4 von Anhang B) abtransportiert werden.
1.4 Diese Norm behandelt nicht die Anforderungen zur Verminderung von Gefährdungen durch mechanische, elektrische, pneumatische, hydraulische oder andere Bauteile oder Maschinen, die in den Normen für ihre allgemeine Verwendung (Typ A, B1 und B2-Normen) behandelt sind.
1.5 Diese Norm behandelt die in Abschnitt 4 aufgeführten Gefährdungen, außer Gefährdungen durch Lärm ), die während des Betriebs und der Wartung von Steinformmaschinen einschließlich der Schnittstellen auftreten können, wenn sie entsprechend den Angaben des Herstellers oder seines bevollmächtigten Vertreters betrieben werden.
ANMERKUNG 1 Eine Änderung ist in Vorbereitung, die Lärm behandelt sowie insbesondere Maßnahmen zur Lärmminderung an der Quelle und ein Geräuschmessverfahren einschließlich der Angabe von Geräuschemissionswerten.
ANMERKUNG 2 Schnittstellen zwischen Steinformmaschinen und anderen Teilen der Anlage werden in EN 12629-1:2000 (Abschnitt 7.2) behandelt.
Diese Norm behandelt Sicherheitsanforderungen und/oder Schutzverfahren, die für diese Maschinen gelten.
1.6 Bei den Vorgaben in dieser Norm wird davon ausg
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocs
La présente partie de l’EN 12629, utilisée avec l’EN 12629-1:2000+A1, s’applique aux machines pour la
fabrication de blocs, bordures de trottoirs, pavés et autres produits similaires en béton.
L’EN 12629-1:2000+A1 spécifie les prescriptions générales applicables aux machines pour la fabrication de produits
de construction en béton et silico-calcaire.
Le présent document spécifie les prescriptions supplémentaires et les dérogations à l’EN 12629-1:2000+A1
spécifiques aux machines concernées."
1.2 !La présente Norme européenne traite tous les phénomènes dangereux significatifs spécifiques
à ces machines, lorsque celles-ci sont utilisées normalement et dans des conditions de mauvais usage que le
fabricant peut raisonnablement prévoir (voir l’Article 4). Cette Norme européenne spécifie les mesures techniques
appropriées pour éliminer ou réduire les risques dus aux phénomènes dangereux significatifs."
1.3 La présente Norme européenne s’applique aux machines, du point où le mélange pénètre dans la machine
(voir points 1 et 2 de l’annexe B) et du point où les palettes sont introduites dans la machine (voir point 3 de
l’annexe B) jusqu’au point où les produits frais sont transférés de la machine au système de cure (voir point 4 de
l’annexe B).
Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 2. del: Stroji za izdelavo blokov
Ta del EN 12629 skupaj z EN 12629-1:2000+A1:2010 velja za stroje za izdelavo blokov, robnikov, tlakovcev in podobnih proizvodov iz betona. EN 12629-1:2000+A1:2010 določa splošne zahteve, ki veljajo za stroje za izdelavo gradbenih proizvodov iz betona in apnenega peščenca. Ta dokument določa dodatne zahteve in/ali odstopanja od EN 12629-1:2000+A1:2010, specifične za stroje, ki jih zajema. Ta evropski standard obravnava vse pomembne nevarnosti, nevarne situacije in primere, ki se nanašajo na te stroje, kadar se uporabljajo kot predvideno in pod pogoji napačne uporabe, ki jih razumno predvidi proizvajalec (glej Klavzulo 4). Ta evropski standard določa primerne tehnične ukrepe za odpravo ali zmanjšanje tveganj, ki se pojavijo zaradi pomembnih nevarnosti. Ta evropski standard velja za stroje od točke, na kateri zmes vstopa v stroj (glej točki 1 in 2 Dodatka B) in točke, na kateri paletne plošče prihajajo v montažo (glej točko 3 Dodatka B), do točke, na kateri gredo zeleni proizvodi iz strojnega sklopa v sušilni sistem (glej točko 4 Dodatka B). Ta evropski standard obravnava nevarnosti, navedene v Klavzuli 4, do katerih lahko pride med obratovanjem in vzdrževanjem strojev za izdelavo blokov, vključno z vmesniki, kadar se izvajata v skladu s specifikacijami, ki jih je navedel proizvajalec ali njegov pooblaščeni zastopnik. Ta standard vzpostavlja varnostne zahteve in/ali zaščitne metode, ki veljajo za te stroje.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: SteinformmaschinenMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocsMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-2:2002+A1:2010SIST EN 12629-2:2004+A1:2010en,fr01-december-2010SIST EN 12629-2:2004+A1:2010SLOVENSKI
STANDARD
SIST EN 12629-2:2004+A1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12629-2:2002+A1
September 2010 ICS 91.220 Supersedes EN 12629-2:2002English Version
Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 2: Block making machines
Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 2: Machines à blocs
Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 2: Steinformmaschinen This European Standard was approved by CEN on 1 November 2002 and includes Amendment 1 approved by CEN on 5 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12629-2:2002+A1:2010: ESIST EN 12629-2:2004+A1:2010
EN 12629-2:2002+A1:2010 (E) 2 Contents page Foreword . 3Introduction . 41Scope . 42Normative references . 53Terms and definitions . 54List of significant hazards . 64.1Mechanical hazards (see informative annex B) . 64.2Electrical hazards . 84.3Hazards generated by vibration . 85!!!!Safety requirements and/or protective measures"""" . 86!!!!Verification of safety requirements and/or protective measures"""" . 97Information for use . 98Marking . 10Annex A (informative)
Mechanical hazards zones for a common block making machine and requirements and measures . 11Annex B (informative)
Terminology of a common block making machine . 12Annex ZA (informative)
!!!! Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC"""" . 13Bibliography . 14
SIST EN 12629-2:2004+A1:2010
EN 12629-2:2002+A1:2010 (E) 3 Foreword This document (EN 12629-2:2002+A1:2010) has been prepared by Technical Committee CEN /TC 151 "Construction equipment and building material machines - Safety", the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by
March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1, approved by CEN on 2010-08-05. This document supersedes EN 12629-2:2002. The start and finish of text introduced or altered by amendment is indicated in the text by tags ! ". !This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document." !The series "Machines for the manufacture of constructional products from concrete and calcium – silicate – Safety" consists of the following parts: Part 1: Common requirements Part 2: Block making machines Part 3: Slide and turntable machines Part 4: Concrete roof tile making machines Part 5.1: Pipe making machines manufacturing in the vertical axis Part 5.2: Pipe making machines manufacturing in the horizontal axis Part 5.3: Pipe prestressing machines Part 5.4: Concrete pipe coating machines Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products Part 7: Stationary and mobile equipment for long line manufacture of prestressed products Part 8: Machines and equipment for the manufacture of constructional products from calcium silicate (and concrete)" !deleted text" According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SIST EN 12629-2:2004+A1:2010
EN 12629-2:2002+A1:2010 (E) 4 Introduction !This European Standard is a Type C-standard as stated in EN ISO 12100. The machinery concerned and the extent to which hazards, hazardous situation and events are covered are indicated in the scope of this document.
When provisions of this type C document are different from those, which are stated in type A or B documents, the provisions of this type C document take precedence over the provisions of the other documents, for machines that have been designed and built according to the provisions of this type C document.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific for the block making machines as described in 1.1. With the aim of clarifying the intentions of the document it should be noticed that the following assumptions were made when producing it: specific conditions of use or environmental conditions out of the scope of the document shall be the subject of negotiations between the manufacturer and the user/owner, the equipment will only be used by competent and designated persons,
the place of use/installation is adequately lit,
all operations are carried out by specially trained operators."
1 Scope 1.1 !This part of EN 12629, taken together with EN 12629-1:2000+A1:2010, applies to machines for the manufacture of blocks, kerbs, paving stones and similar concrete products.
EN 12629-1:2000+A1:2010 specifies general requirements applicable to machines for the manufacture of constructional products from concrete and calcium–silicate.
This document specifies the additional requirements to and/or the deviations from EN 12629-1:2000+A1:2010 specific to the machines it covers." 1.2 !This European Standard deals with all significant hazards pertinent to these machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards." 1.3 This European Standard applies to the machines from the point at which the mixture enters the machine (see point 1-2 of annex B) and the point where the pallet boards are brought to the assembly (see point 3 of annex B) until the point where the green products are removed from the machine assembly to the curing system (see point 4 of annex B). !deleted text" SIST EN 12629-2:2004+A1:2010
EN 12629-2:2002+A1:2010 (E) 5 !!!!1.4"""" This European Standard deals with the hazards !deleted text" listed in clause 4 which can arise during the operation and maintenance, including the interfaces, of the block making machines, when carried out in accordance with the specifications given by the manufacturer or his authorised representative. NOTE 1 Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration. NOTE 2 Interfaces between the block making machines and others of the installation are dealt with in
!EN 12629-1:2000+A1:2010 (7.2)". This standard establishes safety requirements and/or methods of protection which apply to these machines. ! 1.5 This document is not applicable to block making machines, which are manufactured before the date of publication of this document by CEN." 2 Normative references !The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies." !deleted text" !EN 12629-1:2000+A1:2010", Machines for the manufacture of constructional products from concrete and calcium-silicate — Safety — Part 1: Common requirements !EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general prin
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.