FprEN 12167
(Main)Copper and copper alloys - Profiles and bars for general purposes
Copper and copper alloys - Profiles and bars for general purposes
This European Standard specifies the composition, property requirements and dimensional tolerances for copper alloy profiles including L-, T-, U-shaped cross-sections, and bars, finally produced by drawing or extruding.
This European Standard applies to profiles with L-, T- and U-shaped cross-sections which would fit within a circumscribing circle of a maximum 180 mm diameter and to bars with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this European Standard, are also specified.
Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen Verwendung
Dieses Dokument legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für durch Ziehen oder Pressen endgefertigte Profile, einschließlich Profilen mit L-, T- und U-förmigen Quer
schnitten und Rechteckstangen aus Kupferlegierungen fest.
Dieses Dokument gilt für Profile mit L-, T- und U-förmigen Querschnitten mit einem Durchmesser des umschreibenden Kreises von höchstens 180mm und Rechteckstangen mit Dicken von 3mm bis 60mm und Breiten von 6mm bis 120mm.
Der Ablauf der Probenahme und die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforde
rungen dieses Dokuments sind ebenfalls festgelegt.
Cuivre et alliages de cuivre - Profilés et barres pour usages généraux
Le présent document spécifie la composition, les exigences de propriétés et les tolérances dimensionnelles des profilés en alliage de cuivre, incluant les sections en L, T, U et les barres, fabriqués par étirage ou filage.
Le présent document s’applique aux profilés à section en L, T et U s’inscrivant à l’intérieur d’un cercle d’un diamètre maximal de 180 mm, ainsi qu’aux barres d’épaisseur comprise entre 3 mm et 60 mm inclus et de largeur comprise entre 6 mm et 120 mm inclus.
Les modes opératoires d’échantillonnage et les méthodes d’essai pour la vérification de la conformité aux exigences du présent document sont également spécifiés.
Baker in bakrove zlitine - Profili in palice za splošno uporabo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 12167:2022
01-oktober-2022
Baker in bakrove zlitine - Profili in palice za splošno uporabo
Copper and copper alloys - Profiles and bars for general purposes
Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen
Verwendung
Cuivre et alliages de cuivre - Profilés et barres pour usages généraux
Ta slovenski standard je istoveten z: prEN 12167
ICS:
77.150.30 Bakreni izdelki Copper products
oSIST prEN 12167:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN 12167:2022
oSIST prEN 12167:2022
DRAFT
EUROPEAN STANDARD
prEN 12167
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2022
ICS 77.150.30 Will supersede EN 12167:2016
English Version
Copper and copper alloys - Profiles and bars for general
purposes
Cuivre et alliages de cuivre - Profilés et barres pour Kupfer und Kupferlegierungen - Profile und
usages généraux Rechteckstangen zur allgemeinen Verwendung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 133.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12167:2022 E
worldwide for CEN national Members.
oSIST prEN 12167:2022
prEN 12167:2022 (E)
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 Designations. 7
4.1 Material . 7
4.1.1 General . 7
4.1.2 Symbol . 7
4.1.3 Number . 7
4.2 Material condition . 7
4.3 Product . 8
5 Ordering information .10
6 Requirements .11
6.1 Composition .11
6.2 Mechanical properties .11
6.2.1 Profiles .11
6.2.2 Bar .12
6.3 Resistance to dezincification .12
6.4 Residual stress level .12
6.5 Dimensions and tolerances .12
6.5.1 Cross-sectional dimensions .12
6.5.2 Length .12
6.5.3 Flatness .13
6.5.4 Straightness .13
6.5.5 Twist .14
6.5.6 Corner radii of bar .15
6.6 Surface quality.15
6.7 Internal inclusion .15
7 Sampling .15
7.1 General .15
7.2 Analysis .15
7.3 Tensile and hardness tests .16
7.4 Dezincification resistance and stress corrosion resistance tests .16
8 Test methods .16
8.1 Analysis .16
8.2 Tensile test .16
8.2.1 General .16
8.2.2 Location of test pieces .16
8.2.3 Shape and size of test pieces .16
8.2.4 Procedure for testing .17
8.2.5 Expression of results .17
8.3 Hardness test .17
8.4 Dezincification resistance test .17
oSIST prEN 12167:2022
prEN 12167:2022 (E)
8.5 Stress corrosion resistance test . 17
8.6 Retests . 17
8.6.1 Analysis, tensile, hardness and dezincification resistance tests . 17
8.6.2 Stress corrosion resistance test . 18
8.7 Rounding of results . 18
9 Declaration of conformity and inspection documentation . 18
9.1 Declaration of conformity . 18
9.2 Inspection documentation . 18
10 Marking, packaging, labelling . 19
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2014/68/EU (Pressure equipment Directive) aimed to be
covered . 48
Bibliography . 49
oSIST prEN 12167:2022
prEN 12167:2022 (E)
European foreword
This document (prEN 12167:2022) has been prepared by Technical Committee CEN/TC 133 “Copper and
copper alloys”, the secretariat of which is held by DIN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12167:2016.
In comparison with EN 12167:2016, the following significant technical changes were made:
a) Introduction of 6.7 Internal inclusion;
b) Added a new Figure for straightness at 6.5.4.2 and modified values in Table 21;
c) Introduction in the chemical composition Tables of a footnote to explain the meaning of elements for
which no upper and lower limits are defined;
d) CuZn4Si4MnP (CW245E) and CuZn9Si4MnP (CW246E) added in the new Table 2 and new Table 10
e) Chemical composition of CuZn39Pb3 (CW614N), CuZn40Pb2 (CW617N), CuZn35Pb1,5AlAs
(CW625N) and CuZn33Pb1,5AlAs (CW626N) modified in the new Table 7;
f) Added a new alloy CuZn40Pb1 (CW627N) in the new Table 7 and Table 15;
g) Chemical composition of CuZn33Pb1AlSiAs (CW725R) modified in the new Table 8;
h) Added a new alloy CuZn36Si1P (CW726R) in the new Table 8 and Table 16;
i) Annex ZA added.
This document is one of a series of European Standards for the copper and copper alloy products rod,
wire, profile and forgings. Other products are specified as follows:
— EN 12163, Copper and copper alloys — Rod for general purposes;
— EN 12164, Copper and copper alloys — Rod for free machining purposes;
— EN 12165, Copper and copper alloys — Wrought and unwrought forging stock;
— EN 12166, Copper and copper alloys — Wire for general purposes;
— EN 12168, Copper and copper alloys — Hollow rod for free machining purposes;
— EN 13601, Copper and copper alloys — Copper rod, bar and wire for general electrical purposes;
— EN 13602, Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical
conductors;
— EN 13605, Copper and copper alloys — Copper profiles and profiled wire for electrical purposes.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral part
of this document.
oSIST prEN 12167:2022
prEN 12167:2022 (E)
Introduction
The European Committee for Standardization (CEN) draws attention to the fact that it is claimed that
compliance with this document may involve the use of a patent concerning the alloys
CuZn4Si4MnP (CW245E), CuZn9Si4MnP (CW246E), CuZn33Pb1AlSiAs (CW725R), and
CuZn36Si1P (CW726R) given in 6.1.
CEN takes no position concerning the evidence, validity and scope of this patent right.
The holder of this patent right has ensured the CEN that he is willing to negotiate licenses either free of
charge or under reasonable and non-discriminatory terms and conditions with applicants throughout the
world. In this respect, the
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.