EN ISO 4017:2011

Hexagon head screws - Product grades A and B (ISO 4017:2011)

ISO 4017:2011 specifies the characteristics of hexagon head screws with threads from M1,6 up to and including M64, of product grade A for threads M1,6 to M24 and nominal lengths up to and including 10d or 150 mm, whichever is the shorter, and product grade B for threads over M24 or nominal lengths over 10d or 150 mm, whichever is the shorter.

Sechskantschrauben mit Gewinde bis Kopf - Produktklassen A und B (ISO 4017:2011)

Diese Internationale Norm legt Eigenschaften von Sechskantschrauben mit Gewinde bis Kopf und Gewinden von M1,6 bis M64, mit Produktklasse A für Gewinde von M1,6 bis M24 und Nennlängen 10 d oder 150 mm, wobei der kleinere Zahlenwert gilt, fest.
ANMERKUNG Diese Sechskantschrauben entsprechen denen nach ISO 4014. Sie haben lediglich Gewinde bis Kopf und sind handelsüblich nur in Nennlängen bis 200 mm festgelegt.
Falls in besonderen Fällen andere Festlegungen als die in dieser Norm aufgeführten benötigt werden, können diese den entsprechenden ISO-Normen entnommen werden, z. B. ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 und ISO 4759-1.

Vis à tête hexagonale entièrement filetées - Grades A et B (ISO 4017:2011)

L'ISO 4017:2011 spécifie les caractéristiques des vis à tête hexagonale entièrement filetées de diamètre de filetage M1,6 à M64 inclus, de grade A pour les filetages de diamètre M1,6 à M24 inclus et de longueur nominale inférieure ou égale à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue, et de grade B pour les filetages de diamètre supérieur à M24 ou de longueur nominale supérieure à 10d ou à 150 mm, la plus petite des deux valeurs étant retenue.

Vijaki s šestrobo glavo z navojem do glave - Razreda izdelave A in B (ISO 4017:2011)

Ta mednarodni standard določa značilnosti vijakov s šestrobo glavo z navojem do glave od M1,6 do vključno M64 razreda izdelave A za navoje od M1,6 do M24 in z nazivnimi dolžinami do vključno 10d ali 150 mm, odvisno od tega, kaj je krajše, in razreda izdelave B za navoje nad M24 oziroma z nazivnimi dolžinami nad 10d ali 150 mm, odvisno od tega, kaj je krajše.
OPOMBA: Ta tip proizvoda je enak kot tip, zajet z ISO 4014, razen navoja do glave in nominalnih dolžin do in vključno 200 mm kot prednostnih dolžin.
Če se v posebnih primerih zahtevajo specifikacije, ki so drugačne od navedenih v tem mednarodnem standardu, se lahko izberejo med obstoječimi mednarodnimi standardi, na primer ISO 724, ISO 888, ISO 898-1, ISO 965-1, ISO 3506-1, ISO 4753 in ISO 4759-1.

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2011
• Withdrawal Date: 17-Jun-2014
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 18-Jun-2014
• Ref Project: SIST EN ISO 4017:2011 - Hexagon head screws - Product grades A and B (ISO 4017:2011)

Relations

• Replaces: EN ISO 4017:2000 - Hexagon head screws - Product grades A and B (ISO 4017:1999)
• Effective Date: 09-Apr-2011
• Replaced By: EN ISO 4017:2014 - Fasteners - Hexagon head screws - Product grades A and B (ISO 4017:2014)
• Effective Date: 05-Dec-2012

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 4017:2011
01-oktober-2011
1DGRPHãþD
SIST EN ISO 4017:2002
Vijaki s šestrobo glavo z navojem do glave - Razreda izdelave A in B (ISO
4017:2011)
Hexagon head screws - Product grades A and B (ISO 4017:2011)
Sechskantschrauben mit Gewinde bis Kopf - Produktklassen A und B (ISO 4017:2011)
Vis à tête hexagonale entièrement filetées - Grades A et B (ISO 4017:2011)
Ta slovenski standard je istoveten z: EN ISO 4017:2011
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 4017:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 4017:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 4017:2011


EUROPEAN STANDARD
EN ISO 4017

NORME EUROPÉENNE

EUROPÄISCHE NORM
April 2011
ICS 21.060.10 Supersedes EN ISO 4017:2000
English Version
Hexagon head screws - Product grades A and B (ISO
4017:2011)
Vis à tête hexagonale entièrement filetées - Grades A et B Sechskantschrauben mit Gewinde bis Kopf -
(ISO 4017:2011) Produktklassen A und B (ISO 4017:2011)
This European Standard was approved by CEN on 31 January 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4017:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 4017:2011
EN ISO 4017:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 4017:2011
EN ISO 4017:2011 (E)
Foreword
This document (EN ISO 4017:2011) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 "Fasteners", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2011, and conflicting national standards shall be withdrawn at
the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4017:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 4017:2011 has been approved by CEN as a EN ISO 4017:2011 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 4017:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 4017:2011

INTERNATIONAL ISO
STANDARD 4017
Fourth edition
2011-04-01


Hexagon head screws — Product grades
A and B
Vis à tête hexagonale entièrement filetées — Grades A et B





Reference number
ISO 4017:2011(E)
©
ISO 2011

---------------------- Page: 7 ----------------------

SIST EN ISO 4017:2011
ISO 4017:2011(E)


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
...