EN 12697-20:2012

Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)

This European Standard specifies a test method for determining the depth of indentation of mastic asphalt and other asphalt, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base. This European Standard applies to aggregates of maximum nominal size less or equal to 16 mm.

Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder zylindrischen Probekörpern

Diese Europäische Norm legt ein Prüfverfahren zur Bestimmung der Eindringtiefe von Gussasphalt und anderer Asphaltarten bei Beanspruchung mit einem zylindrischen Stempel mit kreisförmiger ebener Grundfläche fest. Diese Europäische Norm gilt für Gesteinskörnungen mit einer maximalen Nenngröße gleich oder kleiner als 16 mm.

Mélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 20: Essai d'indentation sur cubes ou éprouvettes cylindriques (CY)

La présente Norme européenne spécifie une méthode d’essai pour déterminer la profondeur d’indentation
d’un asphalte coulé et d’autres types d’enrobés sous l’effet d’une force exercée par l’intermédiaire d’un
poinçon cylindrique à embout plat circulaire. La présente Norme européenne s’applique à des granulats dont
la granulométrie nominale maximale est inférieure ou égale à 16 mm.

Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 20. del: Preskus z vtiskanjem na kocko ali valjaste preskušance (CY)

Ta evropski standard določa preskusno metodo za ugotavljanje globine vtisa v litem asfaltu ali drugem asfaltu, ko je podvržen sili prek valjastega vtisnega sornika z okroglo ploščato osnovo. Ta evropski standard se uporablja za agregate z največjo nominalno velikostjo, ki je manjša ali enaka 16 mm.

General Information

• Status: Withdrawn
• Publication Date: 10-Apr-2012
• Withdrawal Date: 25-Feb-2020
• ICS: 93.080.20 - Road construction materials
• Technical Committee: CEN/TC 227 - Road materials
• Drafting Committee: CEN/TC 227/WG 1 - Bituminous mixtures
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 26-Feb-2020
• Ref Project: SIST EN 12697-20:2012 - Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)

Relations

• Replaces: EN 12697-20:2003 - Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or Marshall specimens
• Effective Date: 08-Jun-2022
• Replaced By: EN 12697-20:2020 - Bituminous mixtures - Test methods - Part 20: Indentation using cube or Marshall specimens
• Effective Date: 04-Mar-2020

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder zylindrischen ProbekörpernMélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 20: Essai de pénétration de cubes ou éprouvettes MarshallBituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-20:2012SIST EN 12697-20:2012en,fr,de01-junij-2012SIST EN 12697-20:2012SLOVENSKI
STANDARDSIST EN 12697-20:20041DGRPHãþD



SIST EN 12697-20:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-20
April 2012 ICS 93.080.20 Supersedes EN 12697-20:2003English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 20: Essai d'indentation sur cubes ou éprouvettes Marshall
Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder zylindrischen Probekörpern This European Standard was approved by CEN on 26 February 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-20:2012: ESIST EN 12697-20:2012



EN 12697-20:2012 (E) 2 Contents Page Foreword .31Scope .72Normative references .73Apparatus .73.1Moulding of test cubes of mastic asphalt .73.2Indentation test apparatus .84Specimens . 144.1Specimen type . 144.2Number of specimens . 144.3Conditioning . 145Procedure . 145.1Checking . 145.2Test conditions . 145.3Cube specimen preparation . 155.4Cylindrical specimen preparation . 155.5Mounting and temperature conditioning of the specimens
...