EN ISO 3650:1998
(Main)Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998)
Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998)
This International Standard specifies the most important design and metrological characteristics of gauge blocks with a rectangular cross section and a nominal length ln ranging from 0,5 mm to 1000 mm.
Limit deviations and tolerances are stated for the calibration grade K and for the grades 0, 1 and 2 for various measuring purposes.
Geometrische Produktspezifikation (GPS) - Längennormale - Parallelendmaße (ISO 3650:1998)
Diese Norm legt die wichtigsten maßlichen und qualitativen Eigenschaften von P Parallelendmaßen mit einem rechteckigen Querschnitt und einem Nennmaß ln im Bereich von 0,5 mm bis 1000 mm fest. Die Grenzabmaße und Toleranzen werden für die Kalibrierklasse K und für die Toleranzklassen 0,1 und 2 für verschiedene Meßzwecke angegeben.
Spécification géométrique des produits (GPS) - Etalons de longueur - Cales-étalons (ISO 3650:1998)
La présente Norme internationale prescrit les caractéristiques de conception et les caractéristiques métrologiques les plus importantes des cales-étalons de section rectangulaire et de longueur nominale ln comprise entre 0,5 mm
et 1 000 mm.
Elle prescrit les écarts limites et les tolérances des cales de classe d'étalonnage K et de classes 0, 1 et 2 destinées à divers types de mesure.
Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO 3650:1998)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3650:2000
01-december-2000
Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO
3650:1998)
Geometrical product specifications (GPS) - Length standards - Gauge blocks (ISO
3650:1998)
Geometrische Produktspezifikation (GPS) - Längennormale - Parallelendmaße (ISO
3650:1998)
Spécification géométrique des produits (GPS) - Etalons de longueur - Cales-étalons (ISO
3650:1998)
Ta slovenski standard je istoveten z: EN ISO 3650:1998
ICS:
17.040.30 Merila Measuring instruments
SIST EN ISO 3650:2000 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3650:2000
---------------------- Page: 2 ----------------------
SIST EN ISO 3650:2000
---------------------- Page: 3 ----------------------
SIST EN ISO 3650:2000
---------------------- Page: 4 ----------------------
SIST EN ISO 3650:2000
---------------------- Page: 5 ----------------------
SIST EN ISO 3650:2000
---------------------- Page: 6 ----------------------
SIST EN ISO 3650:2000
INTERNATIONAL ISO
STANDARD 3650
Second edition
1998-12-15
Geometrical Product Specifications
(GPS) — Length standards — Gauge blocks
Spécification géométrique des produits (GPS) — Étalons de longueur —
Cales-étalons
A
Reference number
ISO 3650:1998(E)
---------------------- Page: 7 ----------------------
SIST EN ISO 3650:2000
ISO 3650:1998(E)
Contents
1 Scope .1
2 Normative references .1
3 Definitions .1
4 Nomenclature of faces .3
5 Basis of measurement, traceability, reference condition.4
5.1 Unit of length: metre.4
5.2 Traceability of the length of a gauge block.4
5.3 Reference temperature and standard pressure.4
5.4 Reference orientation of gauge blocks .5
6 General dimensions, material properties, marking.5
6.1 General dimensions.5
6.2 Material properties.5
6.2.1 Material .5
6.2.2 Coefficient of thermal expansion.6
6.2.3 Hardness.6
6.2.4 Dimensional stability.6
6.3 Marking .6
7 Metrological requirements.6
7.1 General.6
7.2 Flatness tolerance, t .7
f
7.2.1 Gauge blocks with nominal lengths exceeding 2,5 mm .7
7.2.2 Gauge blocks with nominal lengths up to 2,5 mm .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.