Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS) - Part 13: Optical 3D CMS (ISO 10360-13:2021)

This document specifies the acceptance tests for verifying the performance of an optical 3D coordinate measuring system (CMS) when measuring lengths as stated by the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the optical 3D CMS.
This document is applicable to verification of the measuring performance of CMSs if the surface characteristics (e.g. glossiness, colour) of the object to be scanned are restricted and within a cooperative range.
This document does not apply to other types of CMSs, including those covered by the other parts of the ISO 10360 series.

Geometrische Produktspezifikationen (GPS) - Annahmeprüfung und Bestätigungsprüfung für Koordinatenmesssysteme (KMS) - Teil 13: Optische 3D KMS (ISO 10360-13:2021)

Dieses Dokument legt die Annahmeprüfungen fest, die dazu dienen, die Leistungsfähigkeit eines optischen 3D Koordinatenmesssystems (3D-KMS) für Längenmessungen nach den Angaben des Herstellers nachzuweisen. Außerdem werden die Bestätigungsprüfungen festgelegt, die dem Anwender die periodische Überprüfung der Leistungsfähigkeit des optischen 3D KMS ermöglichen.
Dieses Dokument ist anwendbar für den Nachweis der Messleistung von KMS, falls der Bereich der Oberflächeneigenschaften (z. B. Glanz, Farbe) des zu scannenden Objekts eingegrenzt ist und innerhalb eines kooperativen Bereiches liegt.
Dieses Dokument findet keine Anwendung für andere Arten von KMS, einschließlich derjenigen, die von den anderen Teilen der Normenreihe ISO 10360 abgedeckt werden.

Spécification géométrique des produits (GPS) - Essais de réception et de vérification périodique des systèmes à mesurer tridimensionnels (SMT) - Partie 13: SMT optique 3D (ISO 10360-13:2021)

Le présent document spécifie les essais de réception pour vérifier la performance d’un système à mesurer tridimensionnel (SMT) optique 3D lors de la mesure de longueurs comme indiqué par le fabricant. Elle spécifie également les essais de vérification périodique permettant à l'utilisateur de vérifier ponctuellement les performances du SMT optique 3D.
Le présent document est applicable à la vérification de la performance de mesurage des SMT si les caractéristiques de la surface (par exemple la brillance, la couleur) de l'objet à balayer sont limitées et comprises dans un intervalle coopératif.
Le présent document ne s’applique pas à d’autres types de SMT, y compris ceux couverts par les autres parties de l’ISO 10360.

Specifikacija geometrijskih veličin izdelka (GPS) - Preskusi za sprejemljivost in ponovno overjanje koordinatnih merilnih strojev (KMS) - 13. del: Optični 3D CMS (ISO 10360-13:2021)

General Information

Status
Published
Publication Date
21-Sep-2021
Withdrawal Date
30-Mar-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
22-Sep-2021
Completion Date
22-Sep-2021

Buy Standard

Standard
EN ISO 10360-13:2021
English language
62 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 10360-13:2020
English language
57 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10360-13:2021
01-november-2021
Specifikacija geometrijskih veličin izdelka (GPS) - Preskusi za sprejemljivost in
ponovno overjanje koordinatnih merilnih strojev (KMS) - 13. del: Optični 3D CMS
(ISO 10360-13:2021)
Geometrical product specifications (GPS) - Acceptance and reverification tests for
coordinate measuring systems (CMS) - Part 13: Optical 3D CMS (ISO 10360-13:2021)
Geometrische Produktspezifikation (GPS) - Annahmeprüfung und Bestätigungsprüfung
für Koordinatenmessgeräte (KMG) - Teil 13: Optische 3D KMG (ISO 10360-13:2021)
Spécification géométrique des produits (GPS) - Essais de réception et de vérification
périodique des systèmes à mesurer tridimensionnels (SMT) - Partie 13: SMT optique 3D
(ISO 10360-13:2021)
Ta slovenski standard je istoveten z: EN ISO 10360-13:2021
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
SIST EN ISO 10360-13:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 10360-13:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 10360-13:2021


EN ISO 10360-13
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2021
EUROPÄISCHE NORM
ICS 17.040.30; 17.040.40
English Version

Geometrical product specifications (GPS) - Acceptance and
reverification tests for coordinate measuring systems
(CMS) - Part 13: Optical 3D CMS (ISO 10360-13:2021)
Spécification géométrique des produits (GPS) - Essais Geometrische Produktspezifikation (GPS) -
de réception et de vérification périodique des systèmes Annahmeprüfung und Bestätigungsprüfung für
à mesurer tridimensionnels (SMT) - Partie 13: SMT Koordinatenmessgeräte (KMG) - Teil 13: Optische 3D
optique 3D (ISO 10360-13:2021) KMG (ISO 10360-13:2021)
This European Standard was approved by CEN on 5 September 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10360-13:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 10360-13:2021
EN ISO 10360-13:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 10360-13:2021
EN ISO 10360-13:2021 (E)
European foreword
This document (EN ISO 10360-13:2021) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall
be withdrawn at the latest by March 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN websites.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Aust
...

SLOVENSKI STANDARD
oSIST prEN ISO 10360-13:2020
01-julij-2020
Specifikacija geometrijskih veličin izdelka (GPS) - Preskusi za sprejemljivost in
ponovno overjanje koordinatnih merilnih strojev (KMS) - 13. del: Optični 3D CMS
(ISO/DIS 10360-13:2020)
Geometrical product specifications (GPS) - Acceptance and reverification tests for
coordinate measuring systems (CMS) - Part 13: Optical 3D CMS (ISO/DIS 10360-
13:2020)
Geometrische Produktspezifikation (GPS) - Annahmeprüfung und Bestätigungsprüfung
für Koordinatenmesssysteme (KMS) - Teil 13: Optische 3D KMS (ISO/DIS 10360
13:2020)
Spécification géométrique des produits (GPS) - Essais de réception et de vérification
périodique des systèmes à mesurer tridimensionnels (SMT) - Partie 13: SMT optique 3D
(ISO/DIS 10360-13:2020)
Ta slovenski standard je istoveten z: prEN ISO 10360-13
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
oSIST prEN ISO 10360-13:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 10360-13:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 10360-13:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10360-13
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:
2020-05-28 2020-08-20
Geometrical product specifications (GPS) — Acceptance
and reverification tests for coordinate measuring
systems (CMS) —
Part 13:
Optical 3D CMS
Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des
systèmes à mesurer tridimensionnels (SMT) —
Partie 13: SMT optique 3D
ICS: 17.040.30; 17.040.40
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10360-13:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020

---------------------- Page: 3 ----------------------
oSIST prEN ISO 10360-13:2020
ISO/DIS 10360-13:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 10360-13:2020
ISO/DIS 10360-13:2020(E)

Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Symbols . 6
5 Rated operating conditions .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.