Geometrical product specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS) - Part 10: Laser trackers (ISO 10360-10:2021)

This document specifies the acceptance tests for verifying the performance of a laser tracker by measuring calibrated test lengths, according to the specifications of the manufacturer. It also specifies the reverification tests that enable the user to periodically reverify the performance of the laser tracker. The acceptance and reverification tests given in this document are applicable to laser trackers utilizing a retroreflector, or a retroreflector in combination with a stylus or optical distance sensor, as a probing system. Laser trackers that use interferometric measurement (IFM), absolute distance measurement (ADM) or both can be verified using this document. This document can also be used to specify and verify the relevant performance tests of other spherical coordinate measurement systems that use cooperative targets, such as “laser radar” systems.
NOTE       Systems which do not track the target, such as laser radar systems, will not be tested for probing performance.
This document does not explicitly apply to measuring systems that do not use a spherical coordinate system. However, interested parties can apply this document to such systems by mutual agreement.
This document specifies:
—    performance requirements that can be assigned by the manufacturer or the user of the laser tracker;
—    the manner of execution of the acceptance and reverification tests to demonstrate the stated requirements;
—    rules for proving comformity;
—    applications for which the acceptance and reverification tests can be used.

Geometrische Produktspezifikationen (GPS) - Annahmeprüfung und Bestätigungsprüfung für Koordinatenmesssysteme (KMS) - Teil 10: Lasertracker (ISO 10360 10:2021)

In diesem Dokument werden die Annahmeprüfungen zur Überprüfung der Leistungsfähigkeit eines Lasertrackers durch die Messung von kalibrierten Prüflängen entsprechend den Spezifikationen des Herstellers festgelegt. Außerdem legt es die Bestätigungsprüfungen fest, die dem Anwender eine periodische Überprüfung der Leistungsfähigkeit des Lasertrackers ermöglichen. Die in diesem Dokument angegebenen Annahme- und Bestätigungsprüfungen sind auf Lasertracker anwendbar, die einen Retroreflektor oder einen Retroreflektor in Verbindung mit einem Taster oder einem optischen Abstandssensor als Messkopfsystem verwenden. Lasertracker mit interferometrischer Messung (IFM, en: interferometric measurement), absoluter Abstandsmessung (ADM, en: absolute distance measurement) oder beidem können nach diesem Dokument überprüft werden. Dieses Dokument kann auch für die Spezifikation und Überprüfung der maßgeblichen Leistungsprüfungen anderer Koordinatenmesssysteme mit Kugelkoordinaten herangezogen werden, die kooperative Zielmarken verwenden, wie z. B. „Laserradar“-Systeme.
ANMERKUNG   Systeme, die die Zielmarke nicht verfolgen, wie z. B. Laserradar-Systeme, werden nicht auf Antast-abweichungen geprüft.
Dieses Dokument gilt nicht ausdrücklich für Messsysteme, die kein Kugelkoordinatensystem verwenden. Interessierte Parteien können dieses Dokument jedoch in gegenseitigem Einvernehmen auf derartige Systeme anwenden.
Dieses Dokument spezifiziert:
—   Leistungsanforderungen, die vom Hersteller oder vom Anwender des Lasertrackers zugewiesen werden können;
—   die Art und Weise der Ausführung der Annahme- und Bestätigungsprüfungen, um die festgelegten Anforderungen nachzuweisen;
—   Regeln für den Konformitätsnachweis;
—   Anwendungen, für die die Annahme- und Bestätigungsprüfungen eingesetzt werden können.

Spécification géométrique des produits (GPS) - Essais de réception et de vérification périodique des systèmes à mesurer tridimensionnels (SMT) - Partie 10: Laser de poursuite (ISO 10360-10:2021)

Le présent document spécifie les essais de réception permettant de vérifier, en mesurant des longueurs d'essai étalonnées, que les performances d'un laser de poursuite sont telles que spécifiées par le fabricant. Il spécifie également les essais de vérification périodique permettant à l'utilisateur de vérifier périodiquement les performances du laser de poursuite. Les essais de réception et de vérification périodique décrits dans le présent document s'appliquent aux lasers de poursuite utilisant un rétroréflecteur, ou un rétroréflecteur en combinaison avec un stylet ou un détecteur optique sans contact, comme système de palpage. Les lasers de poursuite qui utilisent un mesurage par interférométrie (IFM), un mesurage par appareil de mesure des distances absolues (ADM), ou les deux, peuvent être vérifiés à l'aide du présent document. Le présent document peut également être utilisée pour spécifier et vérifier les essais de performance pertinents d'autres systèmes de mesure par coordonnées sphériques qui emploient des cibles coopératives, tels que les systèmes « radar à laser ».
NOTE            Les systèmes qui ne suivent pas la cible, tels que les systèmes radar à laser, ne feront pas l'objet d'essais de performance de palpage.
Le présent document ne s'applique pas explicitement aux systèmes de mesure qui n'utilisent pas de système de coordonnées sphériques. Toutefois, les parties intéressées peuvent convenir d'un commun accord d'appliquer le présent document à de tels systèmes.
Le présent document spécifie :
—    les exigences de performance qui peuvent être fixées par le fabricant ou l'utilisateur du laser de poursuite ;
—    l'exécution des essais de réception et de vérification périodique pour démontrer les exigences spécifiées ;
—    les règles pour prouver la conformité ; et
—    les applications pour lesquelles les essais de réception et de vérification périodique peuvent être utilisés.

Specifikacija geometrijskih veličin izdelka (GPS) - Preskusi za sprejemljivost in ponovno overjanje koordinatnih merilnih strojev (KMS) - 10. del: Laserski 3D merilniki (ISO 10360-10:2021)

General Information

Status
Published
Publication Date
14-Sep-2021
Withdrawal Date
30-Mar-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
15-Sep-2021
Completion Date
15-Sep-2021

Relations

Buy Standard

Standard
EN ISO 10360-10:2021
English language
54 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 10360-10:2019 - BARVE
English language
48 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10360-10:2021
01-november-2021
Nadomešča:
SIST EN ISO 10360-10:2016
Specifikacija geometrijskih veličin izdelka (GPS) - Preskusi za sprejemljivost in
ponovno overjanje koordinatnih merilnih strojev (KMS) - 10. del: Laserski 3D
merilniki (ISO 10360-10:2021)
Geometrical product specifications (GPS) - Acceptance and reverification tests for
coordinate measuring systems (CMS) - Part 10: Laser trackers (ISO 10360-10:2021)
Geometrische Produktspezifikationen (GPS) - Annahmeprüfung und
Bestätigungsprüfung für Koordinatenmessgeräte (KMG) - Teil 10: Lasertracker für Punkt-
zu-Punkt-Messungen (ISO 10360-10:2021)
Spécification géométrique des produits (GPS) - Essais de réception et de vérification
périodique des systèmes à mesurer tridimensionnels (SMT) - Partie 10: Laser de
poursuite (ISO 10360-10:2021)
Ta slovenski standard je istoveten z: EN ISO 10360-10:2021
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
SIST EN ISO 10360-10:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 10360-10:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 10360-10:2021


EN ISO 10360-10
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2021
EUROPÄISCHE NORM
ICS 17.040.30 Supersedes EN ISO 10360-10:2016
English Version

Geometrical product specifications (GPS) - Acceptance and
reverification tests for coordinate measuring systems
(CMS) - Part 10: Laser trackers (ISO 10360-10:2021)
Spécification géométrique des produits (GPS) - Essais Geometrische Produktspezifikationen (GPS) -
de réception et de vérification périodique des systèmes Annahmeprüfung und Bestätigungsprüfung für
à mesurer tridimensionnels (SMT) - Partie 10: Laser de Koordinatenmessgeräte (KMG) - Teil 10: Lasertracker
poursuite (ISO 10360-10:2021) für Punkt-zu-Punkt-Messungen (ISO 10360-10:2021)
This European Standard was approved by CEN on 21 August 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10360-10:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 10360-10:2021
EN ISO 10360-10:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 10360-10:2021
EN ISO 10360-10:2021 (E)
European foreword
This document (EN ISO 10360-10:2021) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2022, and conflicting national standards shall
be withdrawn at the latest by March 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10360-10:2016.
Any feedback and questions on this document should be directed to the users’ national standards
body/national
...

SLOVENSKI STANDARD
oSIST prEN ISO 10360-10:2019
01-julij-2019
Specifikacija geometrijskih veličin izdelka (GPS) - Preskusi sprejemljivosti in
ponovnega preverjanja sistemov za merjenje koordinat - 10. del: Laserski 3D
merilniki za merjenje razdalj točka-točka (ISO/DIS 10360-10:2019)
Geometrical product specifications (GPS) - Acceptance and reverification tests for
coordinate measuring systems (CMS) - Part 10: Laser trackers for measuring point-to-
point distances (ISO/DIS 10360-10:2019)
Geometrische Produktspezifikationen (GPS) - Annahmeprüfung und
Bestätigungsprüfung für Koordinatenmessgeräte (KMG) - Teil 10: Lasertracker für Punkt-
zu-Punkt-Messungen (ISO/DIS 10360-10:2019)
Spécification géométrique des produits (GPS) - Essais de réception et de vérification
périodique des systèmes à mesurer tridimensionnels (SMT) - Partie 10: Laser de
poursuite pour mesurer les distances de point à point (ISO/DIS 10360-10:2019)
Ta slovenski standard je istoveten z: prEN ISO 10360-10
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
31.260 Optoelektronika, laserska Optoelectronics. Laser
oprema equipment
oSIST prEN ISO 10360-10:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 10360-10:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 10360-10:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10360-10
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:
2019-05-31 2019-08-23
Geometrical product specifications (GPS) — Acceptance
and reverification tests for coordinate measuring
systems (CMS) —
Part 10:
Laser trackers for measuring point-to-point distances
Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des
systèmes à mesurer tridimensionnels (SMT) —
Partie 10: Laser de poursuite pour mesurer les distances de point à point
ICS: 17.040.30
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10360-10:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 10360-10:2019
ISO/DIS 10360-10:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 10360-10:2019
ISO/DIS 10360-10:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.