iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 12215-5:2018

(Main)

Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2008, including Amd 1:2014)

Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2008, including Amd 1:2014)

2017-06-01: Annex ZB

Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 5: Entwurfsdrücke für Einrumpffahrzeuge, Entwurfsspannungen, Ermittlung der Dimensionierung (ISO 12215-5:2008, einschließlich Amd 1:2014)

Petits navires - Construction de coques et échantillonnage - Partie 5: Pressions de conception pour monocoques, contraintes de conception, détermination de l'échantillonnage (ISO 12215-5:2008, y compris Amd 1:2014)

Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 5. del: Načrtovani tlaki za trupe, načrtovane napetosti in ugotavljanje lastnosti (ISO 12215-5:2008,vključno z dopolnilom A1:2014)

Ta del standarda ISO 12215 se uporablja za določanje načrtovanih tlakov in napetosti ter za določanje zahtevanih lastnosti, vključno z notranjimi strukturnimi pripadniki malih plovil z enim trupom, izdelanih iz z vlakni ojačenih polimernih materialov, aluminija ali jeklenih zlitin, zlepljenega lesa ali drugega ustreznega materiala za gradnjo plovil, z dolžino trupa (LH) med 2,5 m in 24 m v skladu s standardom ISO 8666. Uporablja se le za plovila v brezhibnem stanju.
Uporablja se le za plovila z najvišjo hitrostjo 50 vozlov v pogojih mLDC.
Ocena običajno zajema vse dele plovila, ki se štejejo za vodoodporne ali odporne na vremenske vplive, ko se ocenjujejo stabilnost, nadvodje in vzgon v skladu s standardom ISO 12217, ter so bistveni za varnost plovila in ljudi na krovu.
Za vse zahtevane lastnosti plovila se ta del standarda ISO 12215 uporablja v povezavi s 6. delom za podrobnosti, 7. delom za plovila z več trupi, 8. delom za krmila ter 9. delom za dodatke in priključke opreme.
Opredelitev zahtevanih lastnosti oken, naoknic, pokrovov in vrat je v skladu s
standardom ISO 12216. Nosilna konstrukcija za te elemente je v skladu s tem delom standarda ISO 12215.
OPOMBA 1: Zahtevane lastnosti, izpeljane iz tega dela standarda ISO 12215, se nanašajo predvsem na plovila za rekreacijo, vključno z rekreacijskimi čarterskimi plovili, in morda niso primerne za zmogljiva dirkalna plovila.
OPOMBA 2: Ta del standarda ISO 12215 temelji na predpostavki, da na zahtevane lastnosti vplivajo samo lokalne obremenitve.
OPOMBA 3: Za zahtevane lastnosti iz tega dela standarda ISO 12215 se šteje, da ustrezajo minimalnim zahtevam glede trdnosti motornih in jadrnih plovil, ki so varno ter odgovorno upravljana ob ustreznem poznavanju prevladujočih pogojev.
Tlačne in obremenitvene vrednosti so običajno izražene v paskalih, kilopaskalih ali megapaskalih. Za boljše razumevanje uporabnikov tega dela standarda ISO 12215 so tlačne vrednosti izražene v kilonewtonih na kvadratni meter (1 kN/m2 = 1 kPa), obremenitve ali prilagodljivi moduli pa v newtonih na kvadratni milimeter (1 N/mm2 = 1 MPa).

General Information

Status
Withdrawn
Publication Date
25-Sep-2018
Withdrawal Date
11-Jun-2019
ICS
47.020.10 - Hulls and their structure elements
47.080 - Small craft
Technical Committee
CEN/SS T01 - Shipbuilding and maritime structures
Drafting Committee
CEN/SS T01 - Shipbuilding and maritime structures
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
12-Jun-2019
Directive
2003/44/EC - Approximation of the laws, regulations and administrative provisions of the Member States relating to recreational craft
2013/53/EU - Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC
Mandate
M/542 - [C(2015)8736] Standardisation Request to the European Committee for Standardisation and the European Committee for Electro-technical Standardisation as regards recreational craft and personal watercraft in support of Directive 2013/53/EU of the European Parliament and of the Council of 20 November 2013 on recreational craft and personal watercraft and repealing Directive 94/25/EC.
Ref Project
SIST EN ISO 12215-5:2018 - Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2008,vključno z dopolnilom A1:2014)

Relations

Replaces
EN ISO 12215-5:2008 - Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2008)
Effective Date
03-Oct-2018
Replaces
EN ISO 12215-5:2008/A1:2014 - Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination - Amendment 1 (ISO 12215-5:2008/Amd 1:2014)
Effective Date
03-Oct-2018
Replaced By
EN ISO 12215-5:2019 - Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2019, Corrected version 2024-03)
Effective Date
19-Jun-2019

Buy Standard

EN ISO 12215-5:2018EN ISO 12215-5:2018
PreviousNext
Standard
EN ISO 12215-5:2018
English language
122 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 12215-5:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 12215-5:2008
SIST EN ISO 12215-5:2008/A1:2014
0DODSORYLOD.RQVWUXNFLMDWUXSDLQ]DKWHYDQHODVWQRVWLGHO1DþUWRYDQLWODNL]D
WUXSHQDþUWRYDQHQDSHWRVWLLQXJRWDYOMDQMHODVWQRVWL ,62YNOMXþQR]
GRSROQLORP$
6PDOOFUDIW+XOOFRQVWUXFWLRQDQGVFDQWOLQJV3DUW'HVLJQSUHVVXUHVIRUPRQRKXOOV
GHVLJQVWUHVVHVVFDQWOLQJVGHWHUPLQDWLRQ ,62YNOMXþQR]GRSROQLORP
$
.OHLQH:DVVHUIDKU]HXJH5XPSIEDXZHLVHXQG'LPHQVLRQLHUXQJ7HLO
(QWZXUIVGUFNHIU(LQUXPSIIDKU]HXJH(QWZXUIVVSDQQXQJHQ(UPLWWOXQJGHU
'LPHQVLRQLHUXQJ ,62YNOMXþQR]GRSROQLORP$
3HWLWVQDYLUHV&RQVWUXFWLRQGHODFRTXHHWpFKDQWLOORQQDJH3DUWLH3UHVVLRQVGH
FRQFHSWLRQSRXUPRQRFRTXHVFRQWUDLQWHVGHFRQFHSWLRQGpWHUPLQDWLRQGH
O
pFKDQWLOORQQDJH ,62YNOMXþQR]GRSROQLORP$
Ta slovenski standard je istoveten z: EN ISO 12215-5:2018
ICS:
47.020.10 Ladijski trupi in njihovi Hulls and their structure
konstrukcijski elementi elements
47.080 ýROQL Small craft
SIST EN ISO 12215-5:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 12215-5:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 12215-5:2018


EN ISO 12215-5
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2018
EUROPÄISCHE NORM
ICS 47.080 Supersedes EN ISO 12215-5:2008
English Version

Small craft - Hull construction and scantlings - Part 5:
Design pressures for monohulls, design stresses, scantlings
determination (ISO 12215-5:2008, including Amd 1:2014)
Petits navires - Construction de coques et Kleine Wasserfahrzeuge - Rumpfbauweise und
échantillonnage - Partie 5: Pressions de conception Dimensionierung - Teil 5: Entwurfsdrücke für
pour monocoques, contraintes de conception, Einrumpffahrzeuge, Entwurfsspannungen, Ermittlung
détermination de l'échantillonnage (ISO 12215-5:2008, der Dimensionierung (ISO 12215-5:2008,
y compris Amd 1:2014) einschließlich Amd 1:2014)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12215-5:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 12215-5:2018
EN ISO 12215-5:2018 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 12215-5:2018
EN ISO 12215-5:2018 (E)
European foreword
The text of ISO 12215-5:2008, including Amd 1:2014 has been prepared by Technical Committee
ISO/TC 188 “Small craft” of the International Organization for Standardization (ISO) and has been taken
over as EN ISO 12215-5:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be
withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This documen
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 12215-7:2020(Main)
Small craft - Hull construction and scantlings - Part 7: Determination of loads for multihulls and of their local scantlings using ISO 12215-5 (ISO 12215-7:2020)
SIST EN ISO 12215-7:2021

This document defines the dimensions, local design pressures and global loads acting on multihull craft with a hull length (LH) or load line length of up to 24 m (see Note). It considers all parts of the craft that are assumed watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217 (all parts). Scantlings corresponding to the local design pressures are then assessed using ISO 12215-5.
NOTE       The load line length is defined in the OMI "International Load Lines Convention 1966/2005", it can be smaller than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions.
This document is applicable to multihulls built from the same materials as in ISO 12215-5, in intact condition, and of the two following types:
—          recreational craft, including recreational charter vessels;
—          commercial craft and workboats.
It is not applicable to multihull racing craft designed only for professional racing.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights and doors.
For the complete scantlings of the craft, this document is intended to be used in conjunction with ISO 12215-8 for rudders, ISO 12215-9 for appendages of sailing craft and ISO 12215-10 for rig loads and rig attachment in sailing craft. ISO 12215-6 can be used for additional details.
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (Nm), Pressures in (kN/m2) (1 kN/m2 = 1 kPa), stresses and elastic modulus in (N/mm2) (1 N/mm2 = 1 MPa).

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12215-5:2019(Main)
Small craft - Hull construction and scantlings - Part 5: Design pressures for monohulls, design stresses, scantlings determination (ISO 12215-5:2019, Corrected version 2024-03)
SIST EN ISO 12215-5:2019

This document defines the dimensions, design local pressures, mechanical properties and design stresses for the scantlings determination of monohull small craft with a hull length (LH) or a load line length (see NOTE 1) of up to 24 m. It considers all parts of the craft that are assumed to be watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217.
NOTE 1    The load line length is defined in the IMO "International Load Lines Convention 1966/2005", it can be larger than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions.
The main core of this document determines the local design pressures and stresses for monohulls and details the possible scantlings methods derived from these pressures and stresses, both for monohulls and multihulls (see NOTE 2). The assessment process requires, where relevant, the application of Annexes.
This document is applicable to small craft, in intact condition, of the two following types:
—          recreational craft, including recreational charter vessels;
—          small commercial craft and workboats, see Clause 12 and Annex J.
It is not applicable to racing craft designed only for professional racing.
NOTE 2    Local pressures and stresses for multihulls are given in ISO 12215-7.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights, and doors.
For the complete scantlings of the craft, this document is intended to be used with ISO 12215-8 for rudders, ISO 12215-9 for appendages and ISO 12215-10 for rig loads and rig attachments.
This document covers small craft built from the following materials:
—          fibre-reinforced plastics, either in single skin or sandwich construction;
—          aluminium or steel alloys;
—          glued wood or plywood (single skin or sandwich), excluding traditional wood construction;
—          non-reinforced plastics for craft with a hull length less than 6 m (see Annex D).
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (N.m), pressures in kN/m2 (1 kN/m2 = 1  kPa), stresses and elastic modulus in N/mm2 (1 N/mm2 = 1 Mpa). Max(a;b;c) means that the required value is the maximum of a, b, and c; and min(d;e;f) means that the required value is the minimum of d, e, and f.

  • Standard
    136 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 12215-8:2018(Main)
Small craft - Hull construction and scantlings - Part 8: Rudders (ISO 12215-8:2009, including Cor 1:2010)
SIST EN ISO 12215-8:2018

ISO 12215-8:2009 gives requirements on the scantlings of rudders fitted to small craft with a length of hull of up to 24 m, measured according to ISO 8666. It applies only to monohulls.
ISO 12215-8:2009 does not give requirements on rudder characteristics required for proper steering capabilities.
ISO 12215-8:2009 only considers pressure loads on the rudder due to craft manoeuvring. Loads on the rudder or its skeg, where fitted, induced by grounding or docking, where relevant, are out of scope and need to be considered separately.
Scantlings derived from ISO 12215-8:2009 are primarily intended to apply to recreational craft including charter craft.

  • Standard
    54 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 12217-3(Main)
Small craft - Stability and buoyancy assessment and categorization - Part 3: Boats of hull length less than 6 m (ISO/DIS 12217-3:2020)
oSIST prEN ISO 12217-3:2021

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of craft susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (C or D) appropriate to its design and maximum load.
This document is applicable to boats of hull length less than 6 m, whether propelled by human or mechanical power, except habitable sailing multihulls. Boats of hull length less than 6 m which are fitted with a full deck and quick-draining cockpit(s) complying with ISO 11812 can alternatively be assessed using ISO 12217‑1 or ISO 12217‑2 (for non-sailing and sailing boats, respectively), in which case higher design categories can be assigned.
In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
This document excludes:
—    inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series;
—    personal watercraft covered by ISO 13590 and other similar powered craft;
—    aquatic toys;
—    canoes and kayaks;
—    gondolas and pedalos;
—    sailing surfboards;
—    surfboards, including powered surfboards;
—    hydrofoils, foil stabilized boats and hovercraft when not operating in the displacement mode; and
—    submersibles.
NOTE       Displacement mode means that the boat is only supported by hydrostatic forces.
It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
prEN ISO 12217-2(Main)
Small craft - Stability and buoyancy assessment and categorization - Part 2: -Sailing boats of hull length greater than or equal to 6 m (ISO/DIS 12217-2:2020)
oSIST prEN ISO 12217-2:2021

This document specifies methods for evaluating the stability and buoyancy of intact (i.e. undamaged) boats. The flotation characteristics of boats susceptible to swamping are also encompassed.
The evaluation of stability and buoyancy properties using this document will enable the boat to be assigned to a design category (A, B, C or D) appropriate to its design and maximum load.
This document is principally applicable to boats propelled primarily by sail (even if fitted with an auxiliary engine) of 6 m up to and including 24 m hull length. However, it can also be applied to boats less than 6 m if they are habitable multihulls or can be applied if they do not attain the desired design category specified in ISO 12217‑3 and they are decked and have quick-draining recesses which comply with ISO 11812.
In relation to habitable multihulls, this document includes assessment of susceptibility to inversion, definition of viable means of escape and requirements for inverted flotation.
This document excludes:
—    inflatable and rigid-inflatable boats covered by the ISO 6185 series, except for references made in the ISO 6185 series to specific clauses of the ISO 12217 series;
—    gondolas and pedalos;
—    surfboards including sailing surfboards; and
—    hydrofoils and foil stabilized boats when not operating in the displacement mode.
NOTE       Displacement mode means that the boat is only supported by hydrostatic forces.
It does not include or evaluate the effects on stability of towing, fishing, dredging or lifting operations, which need to be separately considered if appropriate.

  • Draft
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8362-2:2024(Main)
Injection containers and accessories - Part 2: Closures for injection vials (ISO 8362-2:2024)
SIST EN ISO 8362-2:2024

This document specifies the shape, dimensions, material, performance requirements and labelling of closures for injection vials covered by ISO 8362-1 and ISO 8362-4.
The dimensional requirements are not applicable to barrier-coated closures.
Closures specified in this document are intended for single use only.
NOTE            The potency, purity, stability and safety of a medicinal product during its manufacture and storage can strongly be affected by the nature and performance of the primary packaging.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day