Plastics - Styrene-acrylonitrile (SAN) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19064-2:2020)

This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of styrene-acrylonitrile (SAN) moulding and extrusion materials. It gives the requirements for handling the test material and for conditioning both the test material before moulding and the specimens before testing.
This document gives procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made. It lists properties and test methods which are suitable and necessary to characterize SAN moulding and extrusion materials.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this document, as are the designatory properties specified in ISO 19064-1.
The methods of specimen preparation and conditioning, the specimen dimensions and the test procedures specified in this document are used in order to obtain reproducible and comparable test results. Values determined are not always identical to those obtained using specimens of different dimensions or prepared using different procedures.

Kunststoffe - Styrol/Acrylnitril (SAN)-Werkstoffe - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 19064-2:2020)

Dieses Dokument legt die Verfahren zur Herstellung von Probekörpern und die zur Bestimmung der Eigenschaften von Styrol/Acrylnitril (SAN) Werkstoffen anzuwendenden Prüfverfahren fest. Es gibt die Anforderungen an die Behandlung des Probenmaterials und für das Konditionieren des Probenmaterials vor dem Formen und der Probekörper vor der Prüfung an.
Dieses Dokument gibt Verfahren und Bedingungen für die Herstellung der Probekörper und Verfahren für die Bestimmung der Eigenschaften der Werkstoffe an, aus denen diese Probekörper hergestellt werden. Es führt Eigenschaften und Prüfverfahren auf, die geeignet und notwendig sind, um SAN Werkstoffe zu charakterisieren.
Die Eigenschaften wurden aus den in ISO 10350 1 festgelegten allgemeinen Prüfverfahren ausgewählt. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Werkstoffe sind ebenfalls in diesem Dokument enthalten, ebenso wie die kennzeichnenden Eigenschaften nach ISO 19064 1.
Die in diesem Dokument festgelegten Verfahren der Probekörperherstellung und  konditionierung, die Probekörpermaße sowie die Prüfverfahren werden angewendet, um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten. Die gemessenen Werte sind nicht immer mit denen identisch, die bei der Anwendung von Probekörpern anderer Abmessungen oder solchen, die mit anderen Verfahren hergestellt wurden, erhalten werden.

Plastiques - Matériaux à base de styrène-acrylonitrile (SAN) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 19064-2:2020)

Le présent document spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à utiliser pour déterminer les propriétés des matériaux à base de styrène-acrylonitrile (SAN) pour moulage et extrusion. Il donne les exigences relatives à la manipulation du matériau d'essai et au conditionnement du matériau d'essai avant moulage et des éprouvettes avant essai.
Le présent document donne les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesure des propriétés des matériaux à partir desquels les éprouvettes sont obtenues. Il liste les propriétés et méthodes d'essai qui sont utiles et nécessaires pour caractériser les matériaux pour moulage et extrusion à base de SAN.
Les propriétés ont été sélectionnées parmi les méthodes d'essai générales de l'ISO 10350-1. D'autres méthodes d'essai largement utilisées ou qui revêtent une importance particulière pour ces matériaux pour moulage et extrusion sont aussi incluses dans l'ISO 19064-1.
Les méthodes de préparation et de conditionnement, les dimensions d'éprouvette ainsi que les modes opératoires d'essai spécifiés dans le présent document sont utilisés dans le but d'obtenir des résultats d'essai reproductibles et comparables. Les valeurs déterminées ne sont pas toujours identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.

Polimerni materiali - Materiali na osnovi stiren-akrilonitrila (SAN) za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 19064-2:2020)

General Information

Status
Published
Publication Date
31-Mar-2020
Withdrawal Date
30-Oct-2020
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
01-Apr-2020
Completion Date
01-Apr-2020

Relations

Buy Standard

Standard
EN ISO 19064-2:2020
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 19064-2:2019
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19064-2:2020
01-junij-2020
Nadomešča:
SIST EN ISO 4894-2:2000
Polimerni materiali - Materiali na osnovi stiren-akrilonitrila (SAN) za oblikovanje in
ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 19064-
2:2020)
Plastics - Styrene-acrylonitrile (SAN) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO 19064-2:2020)
Kunststoffe - Styrol/Acrylnitril (SAN)-Werkstoffe - Teil 2: Herstellung von Probekörpern
und Bestimmung von Eigenschaften (ISO 19064-2:2020)
Plastiques - Styrène-acrylonitrile (SAN) pour moulage et extrusion - Partie 2: Préparation
des éprouvettes et détermination des propriétés (ISO 19064-2:2020)
Ta slovenski standard je istoveten z: EN ISO 19064-2:2020
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 19064-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19064-2:2020

---------------------- Page: 2 ----------------------
SIST EN ISO 19064-2:2020


EN ISO 19064-2
EUROPEAN STANDARD

NORME EUROPÉENNE

April 2020
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 4894-2:1999
English Version

Plastics - Styrene-acrylonitrile (SAN) moulding and
extrusion materials - Part 2: Preparation of test specimens
and determination of properties (ISO 19064-2:2020)
Plastiques - Matériaux à base de styrène-acrylonitrile Kunststoffe - Styrol/Acrylnitril (SAN)-Werkstoffe - Teil
(SAN) pour moulage et extrusion - Partie 2: 2: Herstellung von Probekörpern und Bestimmung von
Préparation des éprouvettes et détermination des Eigenschaften (ISO 19064-2:2020)
propriétés (ISO 19064-2:2020)
This European Standard was approved by CEN on 21 March 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19064-2:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 19064-2:2020
EN ISO 19064-2:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 19064-2:2020
EN ISO 19064-2:2020 (E)
European foreword
This document (EN ISO 19064-2:2020) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2020, and conflicting national standards shall
be withdrawn at the latest by October 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4894-2:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19064-2:2020 has been approved b
...

SLOVENSKI STANDARD
oSIST prEN ISO 19064-2:2019
01-maj-2019
Polimerni materiali - Materiali na osnovi stiren-akrilonitrila (SAN) za oblikovanje in
ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO/DIS
19064-2:2019)
Plastics - Styrene-acrylonitrile (SAN) moulding and extrusion materials - Part 2:
Preparation of test specimens and determination of properties (ISO/DIS 19064-2:2019)
Kunststoffe - Styrol/Acrylnitril (SAN)-Werkstoffe - Teil 2: Herstellung von Probekörpern
und Bestimmung von Eigenschaften (ISO/DIS 19064-2:2019)
Plastiques - Styrène-acrylonitrile (SAN) pour moulage et extrusion - Partie 2: Préparation
des éprouvettes et détermination des propriétés (ISO/DIS 19064-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 19064-2
ICS:
83.080.20 Plastomeri Thermoplastic materials
oSIST prEN ISO 19064-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 19064-2:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 19064-2:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19064-2
ISO/TC 61/SC 9 Secretariat: KATS
Voting begins on: Voting terminates on:
2019-03-18 2019-06-10
Plastics — Styrene-acrylonitrile (SAN) moulding and
extrusion materials —
Part 2:
Preparation of test specimens and determination of
properties
Plastiques — Styrène-acrylonitrile (SAN) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
ICS: 83.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19064-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 19064-2:2019
ISO/DIS 19064-2:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 19064-2:2019
ISO/DIS 19064-2:2019(E)

Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of the material before moulding .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.