iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10149-3:1995

(Main)

Hot-rolled flat products made of high yield strength steels for cold forming - Part 3: Delivery conditions for normalized or normalized rolled steels

Hot-rolled flat products made of high yield strength steels for cold forming - Part 3: Delivery conditions for normalized or normalized rolled steels

Part 3 of this European Standard, in a4dition to part 1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming.  The grades are given in table 1 (chemical composition) and table 2 (mechanical properties) and are supplied in the normalized or normalized rolled delivery condition as given in 7.2.           The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of ü 1,5 mm and ¿ 20 mm.

Warmgewalzte Flacherzeugnisse aus Stählen mit hoher Streckgrenze zum Kaltumformen - Teil 3: Lieferbedingungen für normalisierend gewalzte Stähle

Der Teil 3 dieser Europäischen Norm gilt in Verbindung mit Teil 1 für Flacherzeugnisse aus warmgewalzten, schweißbaren Stählen mit hoher Streckgrenze, die für die Kaltumformung bestimmt sind. Die Stahlsorten werden mit den Anforderungen nach Tabelle 1 (chemische Zusammensetzung) sowie nach Tabelle 2 (mechanische Eigenschaften) im normalgeglühten oder normalisierend gewalzten Zustand nach 7.2 geliefert. Die Stähle nach dieser Europäischen Norm werden für warmgewalzte Flacherzeugnisse mit Nenndicken von 1,5 mm bis 20 mm verwendet.

Produits plats laminés à chaud en aciers à haute limite d'élasticité pour formage à froid - Partie 3: Conditions de livraison des aciers à l'état normalisé ou laminage normalisant

La partie 3 de la présente norme européenne, vient s'ajouter à la partie 1 et spécifie les caractéristiques des produits plats en aciers soudables, à haute limite d'élasticité, laminés à chaud, pour formage à froid. Les nuances sont données au tableau 1 (composition chimique) et au tableau 2 (caractéristiques mécaniques) et sont livrées à l'état normalisé ou de laminage normalisant comme indiqué en 7.2. Les aciers spécifiés dans la présente norme européenne concernent les produits plats laminés à chaud dans la gamme d'épaisseur >= 1,5 mm et <= 20 mm.

Vroče valjani ploščati izdelki za hladno preoblikovanje iz jekel z veliko napetostjo tečenja - 3. del: Dobavni pogoji za normalizirana ali normalizacijsko valjana jekla

General Information

Status
Withdrawn
Publication Date
09-Sep-1995
Withdrawal Date
24-Sep-2013
ICS
77.140.50 - Flat steel products and semi-products
Technical Committee
ECISS/TC 103 - Structural steels other than reinforcements
Drafting Committee
ECISS/TC 10 - Structural steels - Qualities
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
25-Sep-2013
Completion Date
25-Sep-2013
Directive
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/005 - Mandate to CEN/ECISS concerning standardization in the iron and steel sector
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 10149-3:1998 - Hot-rolled flat products made of high yield strength steels for cold forming - Part 3: Delivery conditions for normalized or normalized rolled steels

Relations

Replaced By
EN 10149-3:2013 - Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels
Effective Date
19-Sep-2009

Buy Standard

EN 10149-3:1998EN 10149-3:1998
PreviousNext
Standard
EN 10149-3:1998
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Warmgewalzte Flacherzeugnisse aus Stählen mit hoher Streckgrenze zum Kaltumformen - Teil 3: Lieferbedingungen für normalisierend gewalzte StähleProduits plats laminés a chaud en aciers a haute limite d'élasticité pour formage a froid - Partie 3: Conditions de livraison des aciers a l'état normalisé ou laminage normalisantHot-rolled flat products made of high yield strength steels for cold forming - Part 3: Delivery conditions for normalized or normalized
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10025-4:2019+A1:2022(Main)
Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels
SIST EN 10025-4:2019+A1:2023

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the thermomechanical rolled condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 150 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storage tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-6:2019+A1:2022(Main)
Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition
SIST EN 10025-6:2019+A1:2023

This document specifies technical delivery conditions for flat products of high yield strength alloy special steels. The grades and qualities are given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) and are supplied in the quenched and tempered condition.
The steels specified in this document are applicable to hot-rolled flat products with a minimum nominal thickness of 3 mm and a maximum nominal thickness of 200 mm for grades S460, S500, S550, S620 and S690, a maximum nominal thickness of 125 mm for grades S890 and S960, in steels which, after quenching and tempering, have a specified minimum yield strength of 460 MPa to 960 MPa.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-5:2019(Main)
Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance
SIST EN 10025-5:2019

This document specifies technical delivery conditions for flat and long products of hot rolled steels with improved atmospheric corrosion resistance in the grades and qualities given in Tables 2 and 3 (chemical composition) and Tables 4 and 5 (mechanical properties) in the usual delivery conditions as given in 6.3.
The thicknesses in which products of the steel grades and qualities specified in this document can be supplied are given in Table 1.
Table 1 - Product forms for the different steel grades with improved atmospheric corrosion resistance depending on their thickness
[table not reproduced]
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-3:2019(Main)
Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels
SIST EN 10025-3:2019

This document specifies technical delivery conditions for flat and long products of hot rolled weldable fine grain structural steels in the normalized/normalized rolled delivery condition in the grades and qualities given in Tables 1 to 3 (chemical composition) and Tables 4 to 6 (mechanical properties) in thickness ≤ 250 mm.
The steels specified in this document are especially intended for use in heavily loaded parts of welded structures such as, bridges, flood gates, storages tanks, water supply tanks, etc., for service at ambient and low temperatures.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10025-2:2019(Main)
Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
SIST EN 10025-2:2019

This document specifies the technical delivery conditions for flat and long products as well as semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 1 to 5 (chemical composition) and Tables 6 to 8 (mechanical properties) in the usual delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 2 and 4) (chemical composition) and Table 7 (mechanical properties). This document does not apply to structural hollow sections (see EN 10210 1 and EN 10219 1) and tubes.
The technical delivery conditions apply to:
-   thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460JR, J0, J2, K2 and S500J0;
-   thicknesses ≤ 400 mm for flat products of qualities JR, J0, J2 and K2;
-   thicknesses ≤ 250 mm for flat and long products of all other grades and qualities.
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
This document foresees that semi-finished products which are to be converted to rolled finished products conforming to this document are the subject of special agreements at the time of the order. The chemical compositions are also agreed to at the time of the order; the values are within the limits of Tables 1 and 2.
For certain grades and product forms suitability for particular applications are specified at the time of the order (see 7.4.2, 7.4.3 and Table 9).

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10164:2018(Main)
Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions
SIST EN 10164:2018

This document specifies deformation properties perpendicular to the surface of the product.
This document may be applied as a supplement to all product standards for flat products and sections of fully killed steels, except stainless steels. It covers products having a nominal thickness (t) between 15 mm and 400 mm of steels with a specified minimum upper yield strength ReH or proof strength Rp0,2 ≤ 960 MPa ) for which improved through thickness properties are required.
This document may be applied to other steel types if agreed at the time of the order.
This document may be applied to products with thickness between 10 mm ≤ t <15 mm if agreed at the time of the order. See option 1.
This document may be applied to products with thickness t > 400 mm if agreed at the time of the order. See Option 2.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10363:2016(Main)
Continuously hot-rolled patterned steel strip and plate/sheet cut from wide strip - Tolerances on dimensions and shape
SIST EN 10363:2016

This European Standard specifies tolerances on dimensions and shape for continuously hot-rolled uncoated patterned steel strip and plate/sheet cut of it in nominal thicknesses up to 20 mm inclusive, of non-alloy and alloy steels in accordance with Table 1 (see also Annex A).
(...)
Steel grades other than those given in Table 1 may be used by agreement only.
This European standard does not apply to stainless steels.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10149-2:2013(Main)
Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels
SIST EN 10149-2:2014

This European Standard, in addition to EN 10149-1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming.
The grades are given in Table 1 (chemical composition) and Table 2 (mechanical properties) and are supplied in the thermomechanically rolled delivery condition as given in 7.2.
The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of:
-   1,5 mm to 20 mm for the steels which have a specified minimum yield strength of 315 MPa ) up to and including 460 MPa1);
-   1,5 mm to 16 mm for the steels which have a specified minimum yield strength of 500 MPa1) up to and including 700 MPa1); and
-   from 2 mm up to 10 mm for the steels with a minimum yield stress in the range from 900 MPa1) to 960 MPa1).

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10149-1:2013(Main)
Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions
SIST EN 10149-1:2014

1.1   This European Standard specifies requirements for flat products made of weldable, hot-rolled, high yield strength alloy quality and special steels for cold forming.
EN 10149-1 specifies the general delivery conditions.
EN 10149-2 specifies the delivery conditions for thermomechanically rolled steels in the grades given in Table 1 (chemical composition) and Table 2 (mechanical properties) of Part 2.
EN 10149-3 specifies the delivery conditions for normalised or normalised rolled steels in the grades given in Table 1 (chemical composition) and Table 2 (mechanical properties) of Part 3.
1.2   This European Standard does not apply to products for pressure vessels and products for which other European Standards exist or European Standards dealing with steels for general structural applications are being prepared:
-   Hot-rolled products of structural steels (see EN 10025 parts 1 to 6);
-   Hot finished structural hollow sections of non-alloy and fine grain steels (see EN 10210-1).

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10149-3:2013(Main)
Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels
SIST EN 10149-3:2014

This European Standard, in addition to EN 10149-1, specifies requirements for flat products made of weldable, hot-rolled, high yield strength steels for cold forming.
The grades are given in Table 1 (chemical composition) and Table 2 (mechanical properties) and are supplied in the normalised or normalised rolled delivery condition as given in 7.2.
The steels specified in this European Standard are applicable to hot-rolled flat products in the thickness range of ≥ 1,5 mm and ≤ 20 mm.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day