iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 10253-4:2008/AC:2009

(Corrigendum)

Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements

Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements

TC - Small editorial improvements and correction in 12.2.2 and replacement of Figure B.3 in B.4.5

Formstücke zum Einschweißen - Teil 4: Austenitische und austenitisch-ferritische (Duplex-)Stähle mit besonderen Prüfanforderungen

Raccords à souder bout à bout - Partie 4: Aciers inoxydables austénitiques et austéno-ferritiques (duplex) avec contrôle spécifique

Cevni fitingi za soležne zvare - 4. del: Kovna avstenitna in avstenitno-feritna (dupleksna) nerjavna jekla s posebnimi zahtevami glede pregledov - Popravek AC

General Information

Status
Published
Publication Date
12-May-2009
ICS
23.040.40 - Metal fittings
77.140.20 - Stainless steels
Technical Committee
ECISS/TC 110 - Steel tubes, and iron and steel fittings
Drafting Committee
ECISS/TC 29/SC 3/WG 4 - Butt welded fittings in austenitic and austenitic ferritic (duplex) stainless steels
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
13-May-2009
Completion Date
13-May-2009
Directive
2014/68/EU - Directive 2014/68/EU of the European Parliament and of the Council of 15 May 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of pressure equipment
97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
Mandate
M/071 - Mandate to CEN for standardization in the field of Pressure equipment
Ref Project
SIST EN 10253-4:2008/AC:2009 - Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements

Relations

Corrects
EN 10253-4:2008 - Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
Effective Date
15-Apr-2009

Buy Standard

EN 10253-4:2008/AC:2009EN 10253-4:2008/AC:2009
PreviousNext
Corrigendum
EN 10253-4:2008/AC:2009
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni fitingi za soležne zvare - 4. del: Kovna avstenitna in avstenitno-feritna (dupleksna) nerjavna jekla s posebnimi zahtevami glede pregledov - Popravek ACFormstücke zum Einschweißen - Teil 4: Austenitische und austenitisch-ferritische (Duplex-)Stähle mit besonderen PrüfanforderungenRaccords à souder bout à bout - Partie 4: Aciers inoxydables austénitiques et austéno-ferritiques (duplex) avec contrôle spécifiqueButt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements77.140.20Visokokakovostna jeklaStainless steels23.040.40Kovinski fitingiMetal fittingsICS:Ta slovenski standard je istoveten z:EN 10253-4:2008/AC:2009SIST EN 10253-4:2008/AC:2009en,fr,de01-julij-2009SIST EN 10253-4:2008/AC:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10253-4:2008/ACMay 2009Mai 2009Mai 2009ICS 23.040.40; 77.140.20English versionVersion FrançaiseDeutsche FassungButt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic(duplex) stainless steels with specific inspection requirementsRaccords à souder bout à bout - Partie 4:Aciers inoxydables austénitiques etausténo-ferritiques (duplex) avec contrôlespécifiqueFormstücke zum Einschweißen - Teil 4:Austenitische und austenitisch-ferritische(Duplex-)Stähle mit besonderenPrüfanforderungenThis corrigendum becomes effective on 13 May 2009 for incorporation in the three official languageversions of the EN.Ce corrigendum prendra effet le 13 mai 2009 pour incorporation dans les trois versions linguistiquesofficielles de la EN.Die Berichtigung tritt am 13.Mai 2009 zur Einarbeitung in die drei offiziellen Sprachfassungen der ENin Kraft.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members.Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier aux
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 10253-2:2021(Main)
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements
SIST EN 10253-2:2021

This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

  • Standard
    145 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-3:2008(Main)
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
SIST EN 10253-3:2009

1.1   This part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic–ferritic (duplex) stainless steel without specific inspection requirements.
It specifies:
   steel grades;
   mechanical properties;
   dimensions and tolerances;
   requirements for inspection and testing;
   inspection documents;
   marking;
   handling and packaging.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-4:2008(Main)
Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
SIST EN 10253-4:2008

1.1   This European Standard specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures.
It specifies:
   the type of fittings;
   type A (see 7.2)
   type B (see 7.3)
   the steel grades;
   the mechanical properties;
   the dimensions and tolerances;
   the requirements for inspection and testing;
   the inspection documents;
   the marking;
   the handling and packaging.
NOTE   In the case of a harmonised supporting standard for materials, presumption of conformity to the Essential Requirement(s) (ESRs) is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently the technical data stated in the material standard should be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive (PED) are satisfied.
1.2   Unless otherwise specified in this European Standard the general technical delivery requirements in EN 10021 apply.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-2:2021/prA1(Amendment)
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements
SIST EN 10253-2:2021/oprA1:2024

This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 10253-4(Main)
Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
kSIST FprEN 10253-4:2021

This document specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel in two test-categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
1)   type A: butt-welding fittings with reduced pressure factor;
2)   type B: butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

  • Draft
    156 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-2:2021(Main)
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements
SIST EN 10253-2:2021

This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

  • Standard
    145 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-3:2008(Main)
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
SIST EN 10253-3:2009

1.1   This part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic–ferritic (duplex) stainless steel without specific inspection requirements.
It specifies:
   steel grades;
   mechanical properties;
   dimensions and tolerances;
   requirements for inspection and testing;
   inspection documents;
   marking;
   handling and packaging.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-4:2008(Main)
Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
SIST EN 10253-4:2008

1.1   This European Standard specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are intended for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures.
It specifies:
   the type of fittings;
   type A (see 7.2)
   type B (see 7.3)
   the steel grades;
   the mechanical properties;
   the dimensions and tolerances;
   the requirements for inspection and testing;
   the inspection documents;
   the marking;
   the handling and packaging.
NOTE   In the case of a harmonised supporting standard for materials, presumption of conformity to the Essential Requirement(s) (ESRs) is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently the technical data stated in the material standard should be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the Pressure Equipment Directive (PED) are satisfied.
1.2   Unless otherwise specified in this European Standard the general technical delivery requirements in EN 10021 apply.

  • Standard
    97 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 10253-2:2021/prA1(Amendment)
Butt-welding pipe fittings - Part 2: Non alloy and ferritic alloy steels with specific inspection requirements
SIST EN 10253-2:2021/oprA1:2024

This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
FprEN 10253-4(Main)
Butt-welding pipe fittings - Part 4: Wrought austenitic and austenitic-ferritic (duplex) stainless steels with specific inspection requirements
kSIST FprEN 10253-4:2021

This document specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel in two test-categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a)   type of fittings;
1)   type A: butt-welding fittings with reduced pressure factor;
2)   type B: butt-welding fittings for use at full service pressure;
b)   steel grades and their chemical compositions;
c)   mechanical properties;
d)   dimensions and tolerances;
e)   requirements for inspection and testing;
f)   inspection documents;
g)   marking;
h)   protection and packaging.
NOTE   The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.

  • Draft
    156 pages
    English language
    sale 10% off
    e-Library read for
    1 day