EN 10163-2:2004

Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats

This Part 2 in addition to Part 1 of this European Standard specifies the delivery requirements which apply to the surface condition of hot-rolled plates and surface condition of the faces of wide flats with thicknesses of 3 mm = t = 400 mm.
NOTE   For plates with a thickness > 400 mm special agreements should be made at the time of the order.

Lieferbedingungen für die Oberflächenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 2: Blech und Breitflachstahl

Zusatzlich zu EN 10163-1 enthalt dieses Dokument die Lieferbedingungen fur die Oberflachenbeschaffenheit
von warmgewalztem Blech und die Oberflachenbeschaffenheit der Flachen von Breitflachstahl in Dicken von
3 mm ¡Ât ¡Â400 mm
ANMERKUNG Fur Bleche in Dicken > 400 mm sollten bei der Bestellung besondere Vereinbarungen getroffen werden.

Conditions de livraison relatives à l'état de surface des tôles, larges plats et profilés en acier laminés à chaud - Partie 2: Tôles et larges plats

En plus de EN 10163-1, le présent document spécifie les exigences de livraison qui s�appliquent à l�état de surface
des tôles laminées à chaud et l�état de surface des faces des larges plats dans la gamme d�épaisseur
3 mm £ t £ 400 mm.
NOTE Pour les tôles d�épaisseur > 400 mm, il est recommandé que les exigences fassent l�objet d�un accord spécial au
moment de la commande.

Zahteve za kakovost površine pri dobavi vroče valjane jeklene pločevine, širokih ploščatih izdelkov in profilov – 2. del: Pločevina in široki ploščati izdelki

General Information

• Status: Published
• Publication Date: 07-Dec-2004
• Withdrawal Date: 29-Jun-2005
• ICS: 77.140.50 - Flat steel products and semi-products
• Technical Committee: ECISS/TC 103 - Structural steels other than reinforcements
• Drafting Committee: ECISS/TC 10 - Structural steels - Qualities
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 03-Sep-2019
• Ref Project: SIST EN 10163-2:2005 - Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats

Relations

• Replaces: EN 10163-2:1991 - Delivery requirements for surface condition of hot rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
• Effective Date: 22-Dec-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Lieferbedingungen für die Oberflächenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 2: Blech und BreitflachstahlConditions de livraison relatives a l'état de surface des tôles, larges plats et profilés en acier laminés a chaud - Partie 2: Tôles et larges platsDelivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats77.140.70Jekleni profiliSteel profiles77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 10163-2:2004SIST EN 10163-2:2005en01-februar-2005SIST EN 10163-2:2005SLOVENSKI
STANDARDSIST EN 10163-2:19971DGRPHãþD



SIST EN 10163-2:2005



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10163-2
December 2004 ICS 77.140.50 Supersedes EN 10163-2:1991 English version
Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats
Conditions de livraison relatives à l'état de surface des tôles, larges plats et profilés en acier laminés à chaud - Partie 2: Tôles et larges plats
Lieferbedingungen für die Oberflächenbeschaffenheit von warmgewalzten Stahlerzeugnissen (Blech, Breitflachstahl und Profile) - Teil 2: Blech und Breitflachstahl This European Standard was approved by CEN on 4 November 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10163-2:2004: ESIST EN 10163-2:2005



EN 10163-2:2004 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 General.4 5 Classification.4 6 Requirements.5 6.1 Depth and affected area of discontinuities.5 6.2 Repair requirements.5 6.2.1 Class A.5 6.2.2 Class B.6 6.3 Repair procedures.6 6.3.1 General.6 6.3.2 Grinding.7 6.3.3 Welding.
...