iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1253-1:2003

(Main)

Gullies for buildings - Part 1: Requirements

Gullies for buildings - Part 1: Requirements

This standard classifies gullies, gives guidance for places of installation and specifies require-ments for the con-struction, design, perfor-man-ce and mar-king of factory made gullies for buildings, irrespective of material, for use in drainage systems operating under gravity including siphonic systems.
NOTE   Although normally used to convey domestic wastewater, industrial wastewater and rainwa-ter, gullies can convey other wastewater provi-ded there is no risk of damage to components or of injury to health.
This standard does not apply to gully tops and manhole tops which are speci-fied in EN 124:1994.

Abläufe für Gebäude - Teil 1: Anforderungen

Avaloirs et siphons pour bâtiments - Partie 1: Spécifications

Cette norme classifie les avaloirs et les siphons, donne des lignes directrices pour les lieux d'installation et spécifie les exigences concernant la construction, la conception, les performances et le marquage des siphons et des avaloirs pour bâtiments fabriqués en usine, indépendamment des matériaux, destinés à être utilisés dans les réseaux d'évacuation gravitaires et les réseaux d'évacuation siphoïdes (à tuyaux pleins).
NOTE   Bien que normalement utilisés pour transporter des eaux usées domestiques et industrielles et de l'eau de pluie, les avaloirs/siphons peuvent transporter d'autres eaux usées à la condition qu'il n'y ait pas de risque d'endommagement des composants ou de danger pour la santé.
Cette norme ne s'applique pas aux dispositifs de fermeture et de couronnement des avaloirs et des siphons qui font l'objet de l'EN 124.

Hišni žlebovi – 1. del: Zahteve

General Information

Status
Withdrawn
Publication Date
20-May-2003
Withdrawal Date
20-Jan-2015
ICS
91.140.80 - Drainage systems
Technical Committee
CEN/TC 165 - Waste water engineering
Drafting Committee
CEN/TC 165/WG 11 - Waste fittings
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
21-Jan-2015
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
SIST EN 1253-1:2003 - Gullies for buildings - Part 1: Requirements

Relations

Replaces
EN 1253-1:1999 - Gullies for buildings - Part 1: Requirements
Effective Date
22-Dec-2008
Replaced By
EN 1253-2:2015 - Gullies for buildings - Part 2: Roof drains and floor gullies without trap
Effective Date
08-Jun-2022
Replaced By
EN 1253-1:2015 - Gullies for buildings - Part 1: Trapped floor gullies with a depth water seal of at least 50 mm
Effective Date
08-Jun-2022

Buy Standard

EN 1253-1:2003EN 1253-1:2003
PreviousNext
Standard
EN 1253-1:2003
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hišni žlebovi – 1. del: ZahteveAbläufe für Gebäude - Teil 1: AnforderungenAvaloirs et siphons pour bâtiments - Partie 1: SpécificationsGullies for buildings - Part 1: Requirements91.140.80Drenažni sistemiDrainage systemsICS:Ta slovenski standard je istoveten z:EN 1253-1:2003SIST EN 1253-1:2003en01-oktober-2003SIST EN 1253-1:2003SLOVENSKI
STANDARDSIST EN 1253-1:20001DGRPHãþD



SIST EN 1253-1:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1253-1May 2003ICS 91.140.80Supersedes EN 1253-1:1999English versionGullies for buildings - Part 1: RequirementsAvaloirs et siphons pour bâtiments - Partie 1:SpécificationsAbläufe für Gebäude - Teil 1: AnforderungenThis European Standard was approved by CEN on 20 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1253-1:2003 ESIST EN 1253-1:2003



EN 1253-1:2003 (E)2ContentspageForeword.31Scope.32Normative references.33Terms and definitions.44Loading strength.75Places of installation.85.1General.85.2Exceptions.86Nominal sizes.87Materials.88Design and construction.98.1General.98.2Appearance.98.3Depth of water seal.98.4Resistance of water seal to pressure.98.5Apertures in gratings.98.6Blockage prevention: trapped gullies.108.6.1Access for cleaning.108.6.2Self-cleansing capacity.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1253-7:2022(Main)
Gullies for buildings - Part 7: Trapped floor gullies with mechanical closure
SIST EN 1253-7:2023

This document classifies floor gullies for domestic waste water for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a mechanical closure (referred to as floor gullies).
NOTE   Floor gullies with a depth of water seal less than 50 mm are not covered by EN 1253-1, EN 1253-7 and EN 1253-8.
These products are intended to be installed where both conditions below are fulfilled:
-   the building does not exceed a ground-floor and three floors above;
-   infrequent use could result in a water seal evaporating.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-6:2022(Main)
Gullies for buildings - Part 6: Trapped floor gullies with a depth of water seal less than 50 mm
SIST EN 1253-6:2023

This document classifies floor gullies for domestic waste water for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a depth of water seal less than 50 mm (referred to as floor gullies).
NOTE   Floor gullies with a depth of water seal less than 50 mm are not covered by EN 1253 1, EN 1253 7 and EN 1253 8.
These products are intended to be installed where the three following conditions are met:
-   space limitation will not accommodate a gully with a 50 mm water seal;
-   the building does not exceed a ground-floor and three floors above;
-   at least two domestic sanitary appliances are installed in addition to the gully but with only one WC on the same branch (connection pipe) or secondary or branch ventilation is installed (see EN 12056 2:2000, 4.3.2 or 4.3.4.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-8:2022(Main)
Gullies for buildings - Part 8: Trapped floor gullies with combined mechanical closure and water seal
SIST EN 1253-8:2023

This document classifies floor gullies for domestic wastewater for use inside buildings, gives guidance, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with combined mechanical closure and water seal (referred to as floor gullies).
NOTE   Floor gullies with combined mechanical closure and water seal are not covered by EN 1253-1, EN 1253-6, EN 1253-7.
These products are intended to be installed where both condition below are fulfilled:
-   the building does not exceed a ground-floor and three floors above;
-   infrequent use could result in a water seal evaporating.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11296-9:2022(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
SIST EN ISO 11296-9:2023

This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement. It does not apply to the structural design of the lining system.
NOTE      Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-5:2017(Main)
Gullies for buildings - Part 5: Gullies with light liquids closure
SIST EN 1253-5:2017

This draft European Standard specifies requirements for the design, construction, performance, application and marking as well as test methods of factory made gullies with a light liquid closure for buildings.
Light liquid closures for buildings shall be applied to avoid uncontrolled discharge of light liquids into drainage systems in case of emergency.
This draft European Standard does not apply to installations for separation of light liquids covered by EN 858-1.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-3:2016(Main)
Gullies for buildings - Part 3: Evaluation of conformity
SIST EN 1253-3:2016

This draft European Standard specifies the requirements for evaluation of conformity for floor gullies, roof drains and access covers for buildings to ensure conformity of these products with EN 1253-1, EN 1253-2 and FprEN 1253-4.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1253-4:2016(Main)
Gullies for buildings - Part 4: Access covers
SIST EN 1253-4:2016

This draft European Standard classifies access covers according to their loading strength and specifies requirements relating to their design, construction, marking, testing and evaluation of conformity.
This draft European Standard classifies and specifies requirements for factory made access covers used for drainage systems inside buildings. This draft standard does not apply to access covers intended for external use which are covered by EN 124 series.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-3:2015(Main)
Wastewater lifting plants for buildings and sites - Part 3: Lifting plants for limited applications
SIST EN 12050-3:2015

This European Standard applies to lifting plants for limited applications for domestic non-commercial wastewater containing or not containing faecal matter and located below flood level.
NOTE   Limited application means that the number of users is small and the plant is located in the same room as the sanitary appliance(s) served by it ) which are installed in accordance with EN 12056–1 and the layout and calculation are in accordance with EN 12056–4.
This European Standard applies to lifting plants for limited applications designed for wastewater containing faecal matter, where there is another WC available above flood level, and the plants serve no more than a single WC to which it is directly connected (at a distance of max. 0,5 m) and one hand washbasin, one shower and one bidet provided no other sanitary appliance is directly or indirectly connected.
This European Standard also applies to lifting plants for limited applications designed for faecal free wastewater, where a maximum of one hand washbasin or kitchen sink plus one further appliance such as a bathtub or a washing machine or a shower or a dish washer or an urinal are connected. No other sanitary appliance shall be directly or indirectly connected.
This European Standard contains general requirements, basic construction and testing principles, together with information on materials.
Construction and testing requirements for non-return valves used in wastewater lifting plants for limited applications are given in EN 12050 4.
This European Standard does not apply for lifting plants for limited applications for wastewater containing faecal matter where WC flushing is carried out by pressure flush valve.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-2:2015(Main)
Wastewater lifting plants for buildings and sites - Part 2: Lifting plants for faecal-free wastewater
SIST EN 12050-2:2015

This European Standard applies to lifting plants for faecal-free wastewater for drainage of locations below flood level in buildings and sites to prevent any backflow of wastewater into the building. These lifting plants may be prefabricated or delivered as prefabricated kits and assembled on site. This standard specifies general requirements, basic construction and testing principles, together with information on materials and assessment and verification of constancy of performance.
Construction and testing requirements for non-return valves used in wastewater lifting plants are given in EN 12050 4.
This European Standard does not apply for pumping installations for drain and sewer systems outside buildings for pumping of municipal wastewater according to EN 752:2008, Annex F.
This European Standard applies also to lifting plants for faecal-free wastewater which are not prefabricated but composed of individual components purchased from different suppliers and put together on site.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12050-4:2015(Main)
Wastewater lifting plants for buildings and sites - Part 4: Non-return valves for faecal-free wastewater and wastewater containing faecal matter
SIST EN 12050-4:2015

This European Standard applies to non-return valves used for faecal-free wastewater and wastewater containing faecal matter lifting plants. This Standard specifies general requirements, basic construction and testing principles together with information on materials and the relevant assessment and verification of constancy of performance.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day