EN ISO 2639:2002

Steels - Determination and verification of the depth of carburized and hardened cases (ISO 2639:2002)

ISO 2639 defines the case-hardened depth, and specifies methods for the determination of this depth, in steel.
It is applicable to
carburized cases and carbonitrided cases;parts that, when heat treated to final hardness, have a hardness of less than 450 HV 1 at a distance of three times the case-hardened depth, from the surface.
The case-hardened depth is defined by special agreement where these conditions are not met.

Stahl - Bestimmung und Prüfung der Einsatzhärtungstiefe (ISO 2639:2002)

Diese Internationale Norm definiert die Einsatzhärtungstiefe und legt Verfahren zur Bestimmung dieser Tiefe bei Stahl fest.
Sie gilt für
a)   die Einsatzhärtung durch Aufkohlen und Karbonitrieren;
b)   Teile, die nach der endgültigen Wärmebehandlung, in einem Abstand von der Oberfläche, der dem Dreifachen der Einsatzhärtungstiefe entspricht, eine Härte von weniger als 450 HV 1 aufweisen.
Sind diese Bedingungen nicht erfüllt, wird die Einsatzhärtungstiefe durch besondere Vereinbarung festgelegt.
Bei Stählen, bei denen das Werkstück in einem Abstand von der Oberfläche gleich der dreifachen Einsatzhärtungstiefe eine Härte aufweist, die größer als 450 HV 1 ist, kann dieses Bewertungsmerkmal ebenfalls angewendet
werden, sofern ein Härtegrenzwert für die Einsatzhärtungstiefe gewählt wird, der - jeweils in Stufen von 25 Einheiten - größer als 550 HV 1 ist.

Acier - Détermination et vérification de la profondeur de cémentation (ISO 2639:2002)

L'ISO 2639:2002 définit la profondeur de cémentation, et spécifie des méthodes de détermination et de vérification de cette profondeur, dans l'acier.
Elle est applicable
1. aux couches cémentées et aux couches carbonitrurées;
2. aux pièces qui ont à l'état du traitement d'utilisation une dureté inférieure à 450 HV 1 à une distance de trois fois la profondeur de cémentation de la surface.
La profondeur de cémentation est définie par convention particulière lorsque ces conditions ne sont pas satisfaites.

Jekla - Določevanje in preverjanje cementacijske in kalilne globine (ISO 2639:2002)

General Information

• Status: Withdrawn
• Publication Date: 31-Oct-2002
• Withdrawal Date: 29-Mar-2022
• ICS: 77.040.99 - Other methods of testing of metals
• Technical Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Drafting Committee: ECISS/TC 2 - Steel - Physico-chemical and non-destructive testing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 30-Mar-2022
• Ref Project: SIST EN ISO 2639:2004 - Steels - Determination and verification of the depth of carburized and hardened cases (ISO 2639:2002)

Relations

• Replaced By: EN ISO 18203:2022 - Steel - Determination of the thickness of surface-hardened layers (ISO 18203:2016)
• Effective Date: 06-Apr-2022

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stahl - Bestimmung und Prüfung der Einsatzhärtungstiefe (ISO 2639:2002)Acier - Détermination et vérification de la profondeur de cémentation (ISO 2639:2002)Steels - Determination and verification of the depth of carburized and hardened cases (ISO 2639:2002)77.080.20JeklaSteels77.040.99Druge metode za preskušanje kovinOther methods of testing of metalsICS:Ta slovenski standard je istoveten z:EN ISO 2639:2002SIST EN ISO 2639:2004en01-marec-2004SIST EN ISO 2639:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 2639November 2002ICS 77.040.99English versionSteels - Determination and verification of the depth of carburizedand hardened cases (ISO 2639:2002)Acier - Détermination et vérification de la profondeur decémentation (ISO 2639:2002)Stahl - Bestimmung und Prüfung der Einsatzhärtungstiefe(ISO 2639:2002)This European Standard was approved by CEN on 15 October 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 2639:2002 ESIST EN ISO 2639:2004

2002-12-18ForewordThis document (EN ISO 2639:2002) has been prepared by Technical Committee ISO/TC 17"Steel" in collaboration with Technical Committee ECISS/TC 2 "Steel - Physico-chemical andnon-destructive testing", the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication ofan identical text or by endorsement, at the latest by May 2003, and conflicting national standardsshall be withdrawn at the latest by May 2003.According to the CEN/CENELEC Internal Regulations, the national standards organizations ofthe following countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.Endorsement noticeThe text of ISO 2639:2002 has been approved by CEN as EN ISO 2639:2002 without anymodifications.NOTE
Normative references to International Standards are listed in Annex ZA (normative).SIST EN ISO 2639:2004

Reference numberISO 2639:2002(E)© ISO 2002
INTERNATIONAL STANDARD ISO2639Third edition2002-11-01Steels — Determination and verification
of the depth of carburized and hardened cases Acier — Détermination et vérification de la profondeur de cémentation
ISO 2639:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
[e-mail] Web
www.iso.ch Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 2639:2002(E) © ISO 2002 – All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 2639 was prepared by Technical Committee ISO/TC 17, St
...