EN ISO 3580:2008
(Main)Welding consumables - Covered electrodes for manual metal arc welding of creep-resisting steels - Classification (ISO 3580:2004)
Welding consumables - Covered electrodes for manual metal arc welding of creep-resisting steels - Classification (ISO 3580:2004)
ISO 3580:2004 specifies requirements for classification of covered electrodes, based on the all-weld metal in the heat-treated condition, for manual metal arc welding of ferritic and martensitic creep-resisting and low alloy elevated temperature steels.
This International Standard is a combined specification for classification utilizing a system based upon the chemical composition of the all-weld metal, with requirements for the yield strength and the average impact energy of 47 J of all-weld metal, or utilizing a system based upon the tensile strength and the chemical composition of all-weld metal.
Schweißzusätze - Umhüllte Stabelektroden zum Lichtbogenhandschweißen von warmfesten Stählen - Einteilung (ISO 3580:2004)
Diese Internationale Norm legt Anforderungen für die Einteilung von umhüllten Stabelektroden zum
Lichtbogenhandschweißen von ferritischen und martensitischen warmfesten Stählen sowie niedrig legierten
Stählen für erhöhte Temperatur fest, basierend auf dem reinen Schweißgut nach Wärmebehandlung.
Diese Internationale Norm enthält eine gemeinsame Spezifikation zur Einteilung nach der chemischen
Zusammensetzung des reinen Schweißgutes mit Anforderungen an Streckgrenze und durchschnittliche
Kerbschlagarbeit von 47 J des reinen Schweißgutes oder nach der Zugfestigkeit und der chemischen
Zusammensetzung des reinen Schweißgutes.
1) Abschnitte und Tabellen, gekennzeichnet durch ein nachgestelltes „A“, können nur für Stabelektroden
angewendet werden, die nach der chemischen Zusammensetzung und Anforderungen an Streckgrenze
und durchschnittliche Kerbschlagarbeit von 47 J des reinen Schweißgutes nach dieser Internationalen
Norm eingeteilt werden.
2) Abschnitte und Tabellen, gekennzeichnet durch ein nachgestelltes „B“, können nur für Stabelektroden
angewendet werden, die nach der Zugfestigkeit und der chemischen Zusammensetzung des reinen
Schweißgutes nach dieser Internationalen Norm eingeteilt werden.
3) Abschnitte und Tabellen, die kein nachgestelltes „A“ oder „B“ enthalten, sind für alle nach dieser
Internationalen Norm eingeteilten Stabelektroden anwendbar.
In einigen Tabellen sind zum Vergleich die Anforderungen an Stabelektroden nach den beiden Normsystemen
zusammengestellt. In Zusammensetzung und Eigenschaften ähnliche Stabelektroden aus beiden Systemen
werden in der betreffenden Tabelle in derselben Zeile in benachbarten Spalten aufgeführt. Die eine Spalte
enthält das für das eine System verbindliche Kurzzeichen, die andere Spalte in Klammern das für die ähnliche
Stabelektrode geltende Kurzzeichen nach dem anderen System.
Produits consommables pour le soudage - Électrodes enrobées pour le soudage manuel à l'arc des aciers résistant au fluage - Classification (ISO 3580:2004)
L'ISO 3580:2004 spécifie les exigences relatives à la classification des électrodes enrobées, d'après le métal fondu hors dilution à l'état traité thermiquement, pour le soudage manuel à l'arc des aciers ferritiques et martensitiques résistant au fluage et des aciers faiblement alliés pour usage à haute température.
L'ISO 3580:2004 propose une spécification mixte permettant une classification utilisant un système basé soit sur la composition chimique du métal fondu hors dilution, avec des exigences sur la limite d'élasticité et l'énergie de rupture moyenne de 47 J pour le métal fondu hors dilution, soit sur la résistance à la traction et la composition chimique du métal fondu hors dilution.
Dodajni materiali za varjenje - Oplaščene elektrode za obločno varjenje jekel, odpornih proti lezenju - Razvrstitev (ISO 3580:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
1DGRPHãþD
SIST EN 1599:1999
'RGDMQLPDWHULDOL]DYDUMHQMH2SODãþHQHHOHNWURGH]DREORþQRYDUMHQMHMHNHO
RGSRUQLKSURWLOH]HQMX5D]YUVWLWHY ,62
Welding consumables - Covered electrodes for manual metal arc welding of creep-
resisting steels - Classification (ISO 3580:2004)
Schweißzusätze - Umhüllte Stabelektroden zum Lichtbogenhandschweißen von
warmfesten Stählen - Einteilung (ISO 3580:2004)
Produits consommables pour le soudage - Électrodes enrobées pour le soudage manuel
à l'arc des aciers résistant au fluage - Classification (ISO 3580:2004)
Ta slovenski standard je istoveten z: EN ISO 3580:2008
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 3580
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2008
ICS 25.160.20 Supersedes EN 1599:1997
English Version
Welding consumables - Covered electrodes for manual metal
arc welding of creep-resisting steels - Classification (ISO
3580:2004)
Produits consommables pour le soudage - Électrodes Schweißzusätze - Umhüllte Stabelektroden zum
enrobées pour le soudage manuel à l'arc des aciers Lichtbogenhandschweißen von warmfesten Stählen -
résistant au fluage - Classification (ISO 3580:2004) Einteilung (ISO 3580:2004)
This European Standard was approved by CEN on 5 April 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3580:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
The text of ISO 3580:2004 has been prepared by Technical Committee ISO/TC 44 “Welding and allied
processes” of the International Organization for Standardization (ISO) and has been taken over as EN ISO
3580:2008 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2008, and conflicting national standards shall be withdrawn
at the latest by November 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1599:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 3580:2004 has been approved by CEN as EN ISO 3580:2008 without any modification.
INTERNATIONAL ISO
STANDARD 3580
Second edition
2004-03-15
Welding consumables — Covered
electrodes for manual metal arc welding
of creep-resisting steels — Classification
Produits consommables pour le soudage — Électrodes enrobées pour
le soudage manuel à l'arc des aciers résistant au fluage —
Classification
Reference number
ISO 3580:2004(E)
©
ISO 2004
ISO 3580:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
ISO 3580:2004(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references . 1
3 Classification. 2
4 Symbols and requirements. 3
5 Mechanical tests . 10
6 Chemical analysis . 11
7 Fillet weld test . 11
8 Retest . 12
9 Technical delivery conditions. 12
10 Examples of designation. 13
Annex A (informative) Classification systems. 14
Annex B (informative) Description of chemical composition designators (classification by
chemical composition) . 16
Annex C (informative) Description of chemical composition designators (classification by tensile
strength and chemical composition) . 17
Annex D (informative) Description of types of electrode covering (classification by chemical
composition). 18
Annex E (informative) Description of types of electrode covering (classification by tensile
strength and chemical composition) . 19
Annex F (informative) Notes on diffusible hydrogen. 21
ISO 3580:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 3580 was prepared in collaboration with the International Institute of Welding which has been approved
by the ISO Council as an international standardizing body in the field of welding.
This second edition cancels and replaces the first edition (ISO 3580:1975), which has been technically revised.
iv © ISO 2004 – All rights reserved
ISO 3580:2004(E)
Introduction
This International Standard proposes a classification aimed at designating covered electrodes, primarily in
terms of the chemical composition of the all-weld metal.
It should be noted that the mechanical properties of all-weld metal test specimens used to classify the
electrodes will vary from those obtained in production joints because of differences in welding procedure such
as electrode diameter, width of weave, welding position and material composition.
The classification according to system A is mainly based on EN 1599. The classification according to
system B is mainly based upon standards used around the Pacific Rim.
Requests for official interpretations of any aspect of this standard should be directed to the Secretariat of
ISO/TC 44/SC 3 via your national standards body, a complete listing of which can be found at www.iso.org
INTERNATIONAL STANDARD ISO 3580:2004(E)
Welding consumables — Covered electrodes for manual metal
arc welding of creep-resisting steels — Classification
1 Scope
This International Standard specifies requirements for classification of covered electrodes, based on the all-
weld metal in the heat-treated condition, for manual metal arc welding of ferritic and martensitic creep-
resisting and low alloy elevated temperature steels.
This document is a combined specification for classification utilizing a system based upon the chemical
composition of the all-weld metal, with requirements for the yield strength and the average impact energy of
47 J of all-weld metal, or utilizing a system based upon the tensile strength and the chemical composition of
all-weld metal.
1) Paragraphs and tables which carry the suffix letter “A” are applicable only to electrodes classified to
the system based upon chemical composition, with requirements for the yield strength and the
average impact energy of 47 J of all-weld metal under this International Standard.
2) Paragraphs and tables which carry the suffix letter “B” are applicable only to electrodes classified to
the system based upon the tensile strength and the chemical composition of all-weld metal under this
International Standard.
3) Paragraphs and tables which do not have either the suffix letter “A” or the suffix letter “B” are
applicable to all covered electrodes classified under this International Standard.
For comparison purposes, some tables include requirements for electrodes classified according to both
systems, placing individual electrodes from the two systems, which are similar in composition and properties,
on adjacent lines in the particular table. In a particular line of the table that is mandatory in one system, the
symbol for the similar electrode from the other system is indicated in parentheses. By appropriate restriction of
the formulation of a particular electrode, it is often, but not always, possible to produce an electrode that can
be classified in both systems, in which case the electrode, and/or its packaging, may be marked with the
classification in either or both systems.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.