EN 10263-5:2001
(Main)Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels
Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels
This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of, any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments).
EN 10020 Definitions and classification of grades of steel
EN 10088-1 Stainless steels - Part 1 : List of stainless steels
EN 10263-1 Steel rod, bars and wire for cold heading and cold extrusion - Part 1 : General technical delivery conditions
Walzdraht, Stäbe und Draht aus Kaltstauch- und Kaltfließpressstählen - Teil 5: Technische Lieferbedingungen für nichtrostende Stähle
1.1 Dieser Teil von EN 10263 gilt für runden Walzdraht, runde Stäbe und Draht aus nichtrostendem
Stahl zum Kaltstauchen und Kaltfließpressen mit einem Durchmesser bis einschließlich:
- 25 mm bei ferritischen und austenitisch-ferritischen Stählen,
- 50 mm bei austenitischen Stählen,
- 100 mm bei martensitischen Stählen.
1.2 Dieser Teil von EN 10263 wird ergänzt durch EN 10263-1.
Barres, fil machine et fils en acier pour transformation à froid et extrusion à froid - Partie 5: Conditions techniques de livraison des aciers inoxydables
1.1 La présente partie 5 de l'EN 10263 s'applique au fil machine, aux barres de section circulaire et aux fils en acier inoxydable pour déformation et extrusion à froid de diamètre inférieur ou égale à :
¾ 25 mm pour les aciers ferritiques et austeno-ferritiques ;
¾ 50 mm pour les aciers austénitiques ;
¾ 100 mm pour les aciers martensitiques.
1.2 La présente partie 5 de l'EN 10263 est complétée par la partie 1 de cette même norme.
Valjana žica, palice in žica za hladno kovanje in hladno iztiskanje - 5. del: Tehnični dobavni pogoji za nerjavna jekla
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Walzdraht, Stäbe und Draht aus Kaltstauch- und Kaltfließpressstählen - Teil 5: Technische Lieferbedingungen für nichtrostende StähleBarres, fil machine et fils en acier pour transformation a froid et extrusion a froid - Partie 5: Conditions techniques de livraison des aciers inoxydablesSteel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chains77.140.60Jeklene palice in drogoviSteel bars and rods77.140.20Visokokakovostna jeklaStainless steelsICS:Ta slovenski standard je istoveten z:EN 10263-5:2001SIST EN 10263-5:2002en01-september-2002SIST EN 10263-5:2002SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10263-5June 2001ICS 77.140.60; 77.140.65English versionSteel rod, bars and steel wire for cold heading and coldextrusion - Part 5: Technical delivery conditions for stainlesssteelsBarres, fil machine et fils en acier pour transformation àfroid et extrusion à froid - Partie 5: Conditions techniquesde livraison des aciers inoxydablesWalzdraht, Stäbe und Draht aus Kaltstauch- undKaltfließpreßstählen - Teil 5: Technische Lieferbedingungenfür nichtrostende StähleThis European Standard was approved by CEN on 19 April 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10263-5:2001 ESIST EN 10263-5:2002
Page 2EN 10263-5:2001CONTENTSPageFOREWORD.31Scope.42Normative references.43Terms and definitions.44Classification and designation.44.1Classification.44.2Designation.45Production Process.46Requirements.46.1Delivery conditions.46.2Chemical composition.56.3Mechanical properties.56.4Surface quality.56.5Supplementary or special requirements.5SIST EN 10263-5:2002
Page 3EN 10263-5:2001FOREWORDThis European Standard has been prepared by Technical Committee ECISS/TC 15 "Wire-rod -Qualities, dimensions, tolerances and specific tests", the secretariat of which is held by UNI.This European Standard shall be given the status of a national standard, either by publication of anidentical text or by endorsement, at the latest by December 2001, and conflicting nationalstandards shall be withdrawn at the latest by December 2001.This European Standard EN 10263 is subdivided as follows:- Part 1:General technical delivery conditions;- Part 2:Technical delivery conditions for steels not intended for heat treatment after coldworking;- Part 3:Technical delivery conditions for case hardening steels;- Part 4:Technical delivery conditions for steels for quenching and tempering- Part 5:Technical delivery conditions for stainless steels.According to the CEN/CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bound to implement this European Standard: Austria, Belgium, CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 10263-5:2002
Page 4EN 10263-5:20011Scope1.1 This Part of EN 10263 is applicable to round rod, round bars and wire made of stainlesssteels intended for cold heading and cold extrusion having a diameter up to and including: 25 mm for ferritic and austenitic-ferritic steels; 50 mm for austenitic steels; 100 mm for martensitic steels1.2This Part of EN 10263 is complemented by EN 10263-1.2Normative referencesThis European Standard incorporates by dated or undated reference, provisions from otherpublications. These normative references are cited at the appropriate places in the text and thepublications are listed hereafter. For dated references, subsequent amendments to or revisions of,any of these publications apply to this European Standard only when incorporated in it byamendment or revision. For undated references the latest edition of the publication referred toapplies (including amendments).EN 10020Definitions and classification of grades of steelEN 10088-1Stainless steels - Part 1 : List of stainless steelsEN 10263-1Steel rod, bars
and wire for cold heading and cold extrusion - Part 1 : Generaltechnical delivery conditions3Terms and definitionsFor the purposes of this standard the definitions in EN 10263-1:2001 and the following apply.3.1Stainless steelsSteels with at least 10,5 % of Cr and max. 1,2 % C are considered as stainless steels if theirresistance to corrosion is of primary importance4Classification and designation4.1ClassificationAll steels covered by this Part of EN 10263 standard are special alloy steel according to EN 10020.From a practical viewpoint these steels are also classified on the basis of their structure, see alsoANNEX B of EN 10088-1:1995.4.2DesignationSee EN 10263-1:2001.5Production ProcessSee EN 10263-1:2001.6Requirements6.1Delivery conditionsThe delivery conditions in which the products covered by this Part of EN 10263 are normallysupplied, the product forms and the applicable requirements are given in table 1.SIST EN 10263-5:2002
Page 5EN 10263-5:20016.2Chemical composition6.2.1Heat analysisThe chemical composition shall be in accordance with the values specified in table 2 for the heatanalysis.6.2.2Product analysisIn cases where a product analysis is requested, the admissible deviations from the valuesspecified for the heat analysis are indicated in table 3.6.3Mechanical propertiesThe mechanical properties of the products, to be determined by the tensile test, shall be inaccordance with the prescriptions given in table 4, 5, 6 and 7.6.4Surface quality6.4.1Rod is normally supplied in the pickled condition.
Mechanical descaling (sandblasting) canalso be used, in which case a subsequent treatment in a pickling solution shall be carried outunless otherwise agreed.
Particular processes such as peeling can also be applied, subject tospecific agreement at the time of enquiry and order.6.4.2Minor surface imperfections which may occur under normal manufacturing conditions, suchas scores originating from rolled-in scale, shall not be regarded as defects.6.4.3Any particular surface requirements may be agreed at the time of enquiry and order.6.5Supplementary or special requirements6.5.1Aptitude to cold formingA test for the verification of the aptitude of products to cold forming may be carried out if agreed atthe time of enquiry and order.If for the verification of the aptitude to cold forming the upsetting test is applied, it shall be carriedout as follows:-a test piece with an in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.