iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 13108-9

(Main)

Bituminous mixtures - Material specifications - Part 9: Asphalt for Ultra-Thin Layers

Bituminous mixtures - Material specifications - Part 9: Asphalt for Ultra-Thin Layers

This document specifies requirements for the bituminous mixtures for Ultra thin layers Asphalt Concrete (UTLAC) for use on roads, airfields and other trafficked areas.
The grading curve of the bituminous mixture for UTLAC is generally gap graded and the upper sieve size of the mix is not less than 5 mm and not greater than 11 mm.
This document includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.
NOTE   Asphalt Concrete very thin layer mixtures with chemical modified binders not covered by EN 13924 are not covered by this document.
The method of bonding is out of the scope of this document.

Asphaltmischgut - Mischgutanforderungen - Teil 9: Asphaltmischgut für extrem dünne Asphaltbetonschichten (UTLAC)

Dieses Dokument legt Anforderungen an Asphaltmischgüter für extrem dünne Asphaltbetonschichten (UTLAC) fest, die für die Verwendung beim Bau von Straßen, Flugplätzen und sonstigen Verkehrsflächen bestimmt sind.
Die Siebkennlinie des Asphaltmischgutes für UTLAC weist im Wesentlichen Ausfallkörnung auf, und die obere Siebgröße der Mischung beträgt mindestens 5 mm und nicht mehr als 11 mm.
Dieses Dokument enthält Anforderungen an die Auswahl der Bestandteile. Es ist in Verbindung mit EN 13108 20 und EN 13108 21 anzuwenden.
ANMERKUNG   Asphaltbetone für sehr dünne Schichten mit chemisch modifizierten Bindemitteln, die nicht durch EN 14023 abgedeckt sind, sind nicht Gegenstand dieser Europäischen Norm.
Das Verbundverfahren ist nicht Gegenstand dieses Dokuments.

Mélanges bitumineux - Spécifications des matériaux - Partie 9: Béton bitumineux ultra-mince (BBUM)

Le présent document donne les spécifications pour les mélanges bitumineux pour bétons bitumineux ultra-minces (BBUM) utilisés pour les routes, aérodromes et autres zones de circulation.
La courbe granulométrique du mélange bitumineux pour bétons bitumineux ultra-minces (BBUM) est essentiellement discontinue et la dimension maximale des granulats du mélange est au moins égale à 5 mm et au plus égale à 11 mm.
Ce document inclut des spécifications pour le choix des constituants. Il est destiné à être utilisé conjointement avec les normes EN 13108-20 et EN 13108-21.
NOTE   Les bétons bitumineux ultra-minces avec des liants chimiquement modifiés qui ne relèvent pas de la norme EN 13924 ne sont pas couverts par le présent document.
La couche d’accrochage ne relève pas du domaine d'application du présent document.

Bitumenske zmesi - Specifikacije materialov - 9. del: Zelo tanke plasti bitumenskega betona (UTLAC)

General Information

Status
Not Published
Publication Date
28-Oct-2012
ICS
93.080.10 - Road construction
93.080.20 - Road construction materials
Technical Committee
CEN/TC 227 - Road materials
Drafting Committee
CEN/TC 227/WG 1 - Bituminous mixtures
Current Stage
4098 - Decision to abandon - Enquiry
Start Date
09-Mar-2012
Completion Date
09-Mar-2012
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/387 - AMENDMENT TO: Mandate M/124 to CEN/CENELEC concerning the execution of standardisation work for harmonized standards on Road construction products
Ref Project
oSIST prEN 13108-9:2010 - Bituminous mixtures - Material specifications - Part 9: Bituminous mixture for Ultra-thin layer Asphalt Concrete (UTLAC)

Buy Standard

prEN 13108-9:2010prEN 13108-9:2010
PreviousNext
Draft
prEN 13108-9:2010
English language
26 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 13108-9:2010
01-junij-2010
Bitumenske zmesi - Specifikacije materialov - 9. del: Zelo tanke plasti
bitumenskega betona (UTLAC)
Bituminous mixtures - Material specifications - Part 9: Bituminous mixture for Ultra-thin
layer Asphalt Concrete (UTLAC)
Asphaltmischgut - Mischgutanforderungen - Teil 9: Asphaltmischgut für extrem dünne
Asphaltbetonschichten (UTLAC)
Mélanges bitumineux - Spécifications des matériaux - Partie 9: Béton bitumineux ultra-
mince (BBUM)
Ta slovenski standard je istoveten z: prEN 13108-9
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
oSIST prEN 13108-9:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13108-9:2010

---------------------- Page: 2 ----------------------
oSIST prEN 13108-9:2010


EUROPEAN STANDARD
DRAFT
prEN 13108-9
NORME EUROPÉENNE

EUROPÄISCHE NORM

March 2010
ICS 93.080.20
English Version
Bituminous mixtures - Material specifications - Part 9:
Bituminous mixture for Ultra-thin layer Asphalt Concrete
(UTLAC)
Mélanges bitumineux - Spécifications des matériaux - Asphaltmischgut - Mischgutanforderungen - Teil 9:
Partie 9: Béton bitumineux ultra-mince (BBUM) Asphaltmischgut für extrem dünne Asphaltbetonschichten
(UTLAC)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 227.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13108-9:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13108-9:2010
prEN 13108-9:2010 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms, definitions, symbols and abbreviations .7
3.1 Terms and definitions .7
3.2 Symbols and abbreviations .8
4 Requirements for constituent materials .8
4.1 General .8
4.2 Binder .8
4.2.1 General .8
4.2.2 Selection of binder.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 13473-1:2019(Main)
Characterization of pavement texture by use of surface profiles - Part 1: Determination of mean profile depth (ISO 13473-1:2019, Corrected version 2021-06)
SIST EN ISO 13473-1:2019

This document describes a test method to determine the average depth of pavement surface macrotexture (see Clause 3) by measuring the profile of a surface and calculating the texture depth from this profile. The technique is designed to provide an average depth value of only the pavement macrotexture and is considered insensitive to pavement microtexture and unevenness characteristics.
The objective of this document is to make available an internationally accepted procedure for determination of pavement surface texture depth which is an alternative to the traditionally used volumetric patch technique (generally using sand or glass beads), giving comparable texture depth values. To this end, this document describes filtering procedures that are designed to give the best possible representation of texture depths determined with the volumetric patch method[13].
Modern profilometers in use are almost entirely of the contactless type (e.g. laser, light slit or light sheet, to mention a few) and this document is primarily intended for this type. However, this does not exclude application of parts of it for other types of profilometers.
This ISO 13473 series has been prepared as a result of a need identified when specifying a test surface for vehicle noise measurement (see ISO 10844:2014[6]). Macrotexture depth measurements according to this document are not generally adequate for specifying test conditions of vehicle or traffic noise measurements, but have limited applications as a supplement in conjunction with other ways of specifying a surfacing.
This test method is suitable for determining the mean profile depth (MPD) of a pavement surface. This MPD can be transformed to a quantity which estimates the macrotexture depth according to the volumetric patch method. It is applicable to field tests as well as laboratory tests on pavement samples. When used in conjunction with other physical tests, the macrotexture depth values derived from this test method are applicable to estimation of pavement skid resistance characteristics (see e.g. Reference [15]), estimation of noise characteristics and assessment of the suitability of paving materials or pavement finishing techniques.
The method, together with other measurements (where applicable), such as porosity or microtexture, can be used to assess the quality of pavements.
This document is adapted for pavement texture measurement and is not intended for other applications. Pavement aggregate particle shape, size and distribution are surface texture features not addressed in this procedure. The method is not meant to provide a complete assessment of pavement surface texture characteristics. In particular, it is known that there are problems in interpreting the result if the method is applied to porous surfaces or to grooved surfaces (see Annex B).
NOTE Other International Standards dealing with surface profiling methods include, for example, References [1], [2] and [3]. Although it is not clearly stated in these, they are mainly used for measuring surface finish (microtexture) of metal surfaces and are not intended to be applied to pavements.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13036-4:2011(Main)
Road and airfield surface characteristics - Test methods - Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test
SIST EN 13036-4:2011

This European Standard describes a method for determining the slip/skid resistance of a surface using a device which remains stationary at the test location. The slip/skid resistance is measured by means of a slider mounted at the end of a pendulum arm.
The method provides a measure of the slip/skid resistance properties of a surface either in the field or in the laboratory.
This method measures the slip/skid resistance of a small area of a surface (approximately 0,01 m2). This should be considered when deciding its applicability to a surface which may have non-homogeneous surface characteristics, e.g. containing ridges or grooves, or is rough textured (exceeding 1,2 mm patch test).
NOTE   As the results from this test are taken at one small location, the results cannot be compared with results from devices e.g. mobile devices, that measure the slip/skid resistance over a long length of a surface.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13036-1:2010(Main)
Road and airfield surface characteristics - Test methods - Part 1: Measurement of pavement surface macrotexture depth using a volumetric patch technique
SIST EN 13036-1:2010

This European Standard specifies a method for determining the average depth of pavement surface
macrotexture by careful application of a known volume of material on the surface and subsequent
measurement of the total area covered. The technique is designed to provide an average depth value of only
the pavement macrotexture and is considered insensitive to pavement microtexture characteristics.
This test method is suitable for field tests to determine the average macrotexture depth of a pavement
surface. When used in conjunction with other physical tests, the macrotexture depth values derived from this
test method can be used to determine the pavement skid resistance capability, noise characteristics and the
suitability of paving materials or finishing techniques. When used with other tests, care should be taken that all
tests are applied at the same location.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13473-1:2019(Main)
Characterization of pavement texture by use of surface profiles - Part 1: Determination of mean profile depth (ISO 13473-1:2019, Corrected version 2021-06)
SIST EN ISO 13473-1:2019

This document describes a test method to determine the average depth of pavement surface macrotexture (see Clause 3) by measuring the profile of a surface and calculating the texture depth from this profile. The technique is designed to provide an average depth value of only the pavement macrotexture and is considered insensitive to pavement microtexture and unevenness characteristics.
The objective of this document is to make available an internationally accepted procedure for determination of pavement surface texture depth which is an alternative to the traditionally used volumetric patch technique (generally using sand or glass beads), giving comparable texture depth values. To this end, this document describes filtering procedures that are designed to give the best possible representation of texture depths determined with the volumetric patch method[13].
Modern profilometers in use are almost entirely of the contactless type (e.g. laser, light slit or light sheet, to mention a few) and this document is primarily intended for this type. However, this does not exclude application of parts of it for other types of profilometers.
This ISO 13473 series has been prepared as a result of a need identified when specifying a test surface for vehicle noise measurement (see ISO 10844:2014[6]). Macrotexture depth measurements according to this document are not generally adequate for specifying test conditions of vehicle or traffic noise measurements, but have limited applications as a supplement in conjunction with other ways of specifying a surfacing.
This test method is suitable for determining the mean profile depth (MPD) of a pavement surface. This MPD can be transformed to a quantity which estimates the macrotexture depth according to the volumetric patch method. It is applicable to field tests as well as laboratory tests on pavement samples. When used in conjunction with other physical tests, the macrotexture depth values derived from this test method are applicable to estimation of pavement skid resistance characteristics (see e.g. Reference [15]), estimation of noise characteristics and assessment of the suitability of paving materials or pavement finishing techniques.
The method, together with other measurements (where applicable), such as porosity or microtexture, can be used to assess the quality of pavements.
This document is adapted for pavement texture measurement and is not intended for other applications. Pavement aggregate particle shape, size and distribution are surface texture features not addressed in this procedure. The method is not meant to provide a complete assessment of pavement surface texture characteristics. In particular, it is known that there are problems in interpreting the result if the method is applied to porous surfaces or to grooved surfaces (see Annex B).
NOTE Other International Standards dealing with surface profiling methods include, for example, References [1], [2] and [3]. Although it is not clearly stated in these, they are mainly used for measuring surface finish (microtexture) of metal surfaces and are not intended to be applied to pavements.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13036-4:2011(Main)
Road and airfield surface characteristics - Test methods - Part 4: Method for measurement of slip/skid resistance of a surface: The pendulum test
SIST EN 13036-4:2011

This European Standard describes a method for determining the slip/skid resistance of a surface using a device which remains stationary at the test location. The slip/skid resistance is measured by means of a slider mounted at the end of a pendulum arm.
The method provides a measure of the slip/skid resistance properties of a surface either in the field or in the laboratory.
This method measures the slip/skid resistance of a small area of a surface (approximately 0,01 m2). This should be considered when deciding its applicability to a surface which may have non-homogeneous surface characteristics, e.g. containing ridges or grooves, or is rough textured (exceeding 1,2 mm patch test).
NOTE   As the results from this test are taken at one small location, the results cannot be compared with results from devices e.g. mobile devices, that measure the slip/skid resistance over a long length of a surface.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13036-1:2010(Main)
Road and airfield surface characteristics - Test methods - Part 1: Measurement of pavement surface macrotexture depth using a volumetric patch technique
SIST EN 13036-1:2010

This European Standard specifies a method for determining the average depth of pavement surface
macrotexture by careful application of a known volume of material on the surface and subsequent
measurement of the total area covered. The technique is designed to provide an average depth value of only
the pavement macrotexture and is considered insensitive to pavement microtexture characteristics.
This test method is suitable for field tests to determine the average macrotexture depth of a pavement
surface. When used in conjunction with other physical tests, the macrotexture depth values derived from this
test method can be used to determine the pavement skid resistance capability, noise characteristics and the
suitability of paving materials or finishing techniques. When used with other tests, care should be taken that all
tests are applied at the same location.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 56008:2024(Main)
Innovation management - Tools and methods for innovation operation measurements - Guidance (ISO 56008:2024)
SIST EN ISO 56008:2024

This document provides guidance for the definition, implementation, evaluation, and improvement of the measurements necessary to effectively manage innovation activities in an organization. It establishes the fundamentals of innovation operation measurements and guides their application towards four areas:
—     measurements for establishing and launching innovation initiatives;
—     measurements for innovation processes;
—     measurements for innovation initiatives;
—     measurements of innovation portfolios.
This document is applicable to:
—     organizations that are seeking to define and implement an innovation operations measurement approach;
—     organizations and interested parties seeking to improve the areas of accountability, transparency, and evidence-based assessment of innovation operations;
—     customers, investors, and other interested parties, seeking confidence in the organization’s innovation operations management and its results;
—     providers of training in innovation operations and measurements, including assessment of and consultancy for achieving results;
—     experts in innovation operations evaluation and impact assessment, favoring the use of a harmonized international guidance standard;
—     innovation policy makers and program managers who are looking to obtain evidence of progress and desired outcomes of innovation activities supported through public policies and programs.
All of the guidance provided within this document is generic and intended to be applicable to:
—     all types of organizations regardless of sector or size, whether they be private, public, not-for-profit, governmental or societal;
—     all types of innovations (e.g. product, service, process, model, and method) ranging from incremental to radical;
—     all types of time horizons, from short-term to long-term evaluation and measurement.

  • Standard
    85 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4641:2024(Main)
Rubber hoses and hose assemblies for water suction and discharge - Specification (ISO 4641:2024)
SIST EN ISO 4641:2024

This document specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies.
Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges:
—     ambient temperatures: −25 °C to +70 °C;
—     water temperatures during operation: 0 °C to +70 °C.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12845-3:2024(Main)
Fixed firefighting systems - Automatic sprinkler systems - Part 3: Guidance for earthquake bracing
SIST EN 12845-3:2024

This document specifies requirements for earthquake protection of automatic sprinkler systems in accordance with EN 12845:2015+A1:2019.
This document applies only to locations in earthquake zones in accordance with EN 1998-1:2004, 3.2.1 and the Nationally Determined Parameters.
NOTE   The requirements in this document are based on the principle that certain peak ground acceleration values are considered as an earthquake which require special means. Attention is drawn to EN 1998-1:2004, where a peak ground acceleration above 0,08 g (0,78 m/s2) is considered an earthquake risk. Additional characteristics, NDP and/or NCI can exist in some countries as well as national annexes.
The principles defined in this document can be applicable to other water based fixed manual or automatic fire fighting systems, according to local requirements.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 18847:2024(Main)
Solid biofuels - Determination of particle density of pellets and briquettes (ISO 18847:2024)
SIST EN ISO 18847:2024

This document specifies a method for determining the particle density of compressed fuels such as pellets or briquettes. Particle density is not an absolute value and conditions for its determination have to be standardized to enable comparative determinations to be made.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day