prEN 10088-3
(Main)Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes
This document specifies the technical delivery conditions for semi-finished products, hot or cold formed bars, rods, wire, sections and bright products of standard grades and special grades of corrosion resistant stainless steels for general purposes.
NOTE General purposes include the use of stainless steels in contact with foodstuffs.
The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this document, unless otherwise specified in this document.
This document does not apply to components manufactured by further processing of the product forms listed above with quality characteristics altered as a result of such further processing.
Nichtrostende Stähle - Teil 3: Technische Lieferbedingungen für Halbzeug, Stäbe, Walzdraht, gezogenen Draht, Profile und Blankstahlerzeugnisse aus korrosionsbeständigen Stählen für allgemeine Verwendung
Dieses Dokument enthält die technischen Lieferbedingungen für Halbzeug, warm oder kalt umgeformte Stäbe, Walzdraht, gezogenen Draht, Profile und Blankstahlerzeugnisse aus Standardgüten und Sondergüten korrosionsbeständiger nichtrostender Stähle für allgemeine Verwendung.
ANMERKUNG Allgemeine Verwendung schließt die Verwendung von nichtrostenden Stählen in Berührung mit Lebensmitteln ein.
Zusätzlich zu den Angaben dieser Europäischen Norm gelten, sofern in dieser Europäischen Norm nichts anderes festgelegt ist, die in EN 10021 festgelegten allgemeinen technischen Lieferbedingungen.
Dieses Dokument gilt nicht für die durch Weiterverarbeitung der oben genannten Erzeugnisformen hergestellten Teile mit fertigungsbedingt abweichenden Gütemerkmalen.
Aciers inoxydables - Partie 3: Conditions techniques de livraison pour les demi-produits, barres, fils tréfilés, profils et produits transformés à froid en acier résistant à la corrosion pour usage général
Le présent document spécifie les conditions techniques de livraison des demi-produits, des barres laminées à chaud ou transformées à froid, du fil machine, fils tréfilés et des profils en nuances standardisées et en nuances spéciales d'aciers inoxydables résistant à la corrosion pour usage général.
NOTE L’usage général inclut l’utilisation des aciers inoxydables pour le contact alimentaire.
Les conditions techniques de livraison spécifiées dans l'EN 10021 s'appliquent en plus des spécifications du présent document, sauf en cas de spécification contraire dans le présent document.
Le présent document ne s'applique pas aux composants fabriqués par transformation ultérieure des produits énumérés ci-dessus, avec les modifications des caractéristiques de qualité qui en résultent.
Nerjavna jekla - 3. del: Tehnični dobavni pogoji za polizdelke, drogove, palice, žico, profile in svetle izdelke iz korozijsko odpornih jekel za splošno uporabo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 10088-3:2022
01-januar-2022
Nerjavna jekla - 3. del: Tehnični dobavni pogoji za polizdelke, drogove, palice, žico,
profile in svetle izdelke iz korozijsko odpornih jekel za splošno uporaboStainless steels - Part 3: Technical delivery conditions for semi-finished products, bars,
rods, wire, sections and bright products of corrosion resisting steels for general purposes
Nichtrostende Stähle - Teil 3: Technische Lieferbedingungen für Halbzeug, Stäbe,Walzdraht, gezogenen Draht, Profile und Blankstahlerzeugnisse aus
korrosionsbeständigen Stählen für allgemeine Verwendung
Aciers inoxydables - Partie 3: Conditions techniques de livraison pour les demi-produits,
barres, fils tréfilés, profils et produits transformés à froid en acier résistant à la corrosion
pour usage généralTa slovenski standard je istoveten z: prEN 10088-3
ICS:
77.140.20 Visokokakovostna jekla Stainless steels
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
77.140.65 Jeklene žice, jeklene vrvi in Steel wire, wire ropes and
verige link chains
oSIST prEN 10088-3:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------oSIST prEN 10088-3:2022
---------------------- Page: 2 ----------------------
oSIST prEN 10088-3:2022
DRAFT
EUROPEAN STANDARD
prEN 10088-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2021
ICS 77.140.20; 77.140.50; 77.140.65 Will supersede EN 10088-3:2014
English Version
Stainless steels - Part 3: Technical delivery conditions for
semi-finished products, bars, rods, wire, sections and
bright products of corrosion resisting steels for general
purposes
Aciers inoxydables - Partie 3: Conditions techniques de Nichtrostende Stähle - Teil 3: Technische
livraison pour les demi-produits, barres, fils tréfilés, Lieferbedingungen für Halbzeug, Stäbe, Walzdraht,
profils et produits transformés à froid en acier gezogenen Draht, Profile und Blankstahlerzeugnisse
résistant à la corrosion pour usage général aus korrosionsbeständigen Stählen für allgemeine
VerwendungThis draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 5.If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10088-3:2021 E
worldwide for CEN national Members.---------------------- Page: 3 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
Contents Page
European foreword ....................................................................................................................................................... 3
Introduction ..................................................................................................................................................................... 4
1 Scope .................................................................................................................................................................... 5
2 Normative references .................................................................................................................................... 5
3 Terms and definitions .................................................................................................................................... 6
4 Designation and ordering ............................................................................................................................. 6
4.1 Designation of steel grades .......................................................................................................................... 6
4.2 Designation to be used on ordering .......................................................................................................... 7
5 Classification of grades .................................................................................................................................. 7
6 Requirements .................................................................................................................................................... 8
6.1 Steelmaking process ....................................................................................................................................... 8
6.2 Delivery condition ........................................................................................................................................... 8
6.3 Chemical composition .................................................................................................................................... 8
6.4 Chemical corrosion properties ................................................................................................................... 8
6.5 Mechanical properties ................................................................................................................................... 8
6.6 Surface quality .................................................................................................................................................. 9
6.7 Internal soundness ......................................................................................................................................... 9
6.8 Formability at room temperature .......................................................................................................... 10
6.9 Dimensions and tolerances on dimensions and shape ................................................................... 10
6.10 Calculation of mass and tolerances on mass....................................................................................... 10
7 Inspection and testing ................................................................................................................................. 10
7.1 General ............................................................................................................................................................. 10
7.2 Agreement on tests and inspection documents ................................................................................. 10
7.3 Specific inspection and testing ................................................................................................................ 11
7.4 Test methods .................................................................................................................................................. 11
7.5 Retests .............................................................................................................................................................. 12
8 Marking ............................................................................................................................................................ 12
Annex A (informative) List of all stainless steel grades that appear in the document ..................... 66
Annex B (informative) Guidelines for further treatment (including heat treatment) in
fabrication ....................................................................................................................................................... 68
Annex C (informative) Availability of corrosion resistant steel wire in the cold work-
hardened condition ..................................................................................................................................... 76
Annex D (informative) Applicable dimensional standards ........................................................................ 78
Bibliography ................................................................................................................................................................. 79
---------------------- Page: 4 ----------------------oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
European foreword
This document (prEN 10088-3:2021) has been prepared by Technical Committee CEN/TC 459/SC 5
“Steels for heat treatment, alloy steels, free-cutting steels and stainless steels”, the secretariat of which
is held by DIN.This document is currently submitted to the CEN Enquiry.
This document will supersede EN 10088-3:2014.
In comparison with the previous edition, the following technical modifications have been made:
a) addition of austenitic grades, 1.4681, 1.4391 addition of austenitic-ferritic (duplex) grades, 1.4670
addition of ferritic grades, 1.4106, 1.4114, 1.4045 addition of martensitic grade 1.4037;
b) chemical composition was changed for following grades: austenitic grades 1.4310, 1.4404, 1.4529,
ferritic grade 1.4003 and for martensitic grade 1.4028, 1.4116;c) removal of austenitic grades, 1.4319, 1.4537;
d) mechanical values for bright bars have been changed for austenitic grades 1.4301, 1.4307 for
ferritic grades 1.4509 and for martensitic grades 1.4028, 1.4418.EN 10088, under the general title Stainless steels, consists of the following parts:
— Part 1: List of stainless steels (including a table of European Standards, in which these stainless
steels are further specified, see Annex C);— Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resistant steels for general
purposes;— Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright
products of corrosion resistant steels for general purposes;— Part 4: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for
construction purposes;— Part 5: Technical delivery conditions for bars, rods, wire, sections and bright products of corrosion
resisting steels for construction purposes.---------------------- Page: 5 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
Introduction
The European Committee for Standardization (CEN) draws attention to the fact that it is claimed that
compliance with this document may involve the use of patents applied to ten steel grades.
CEN takes no position concerning the evidence, validity and scope of these patent rights.
The holders of these patent rights have ensured CEN that they are willing to negotiate licenses, under
reasonable and non-discriminatory terms and conditions, with applicants throughout the world. In this
respect, the statements of the holders of these patent rights are registered with CEN. Information may
be obtained from:Grade 1.4658:
Sandvik AB
SE-811 81 Sandviken, Sweden
Grade: 1.4662
Outokumpu Stainless AB
SE-77480 Avesta, Sweden
Grade 1.4062, 1.4669, 1.4670
Ugitech
F-73403 Ugine Cedex, France,
Grade 1.4062, 1.4669
Industeel
F-71200 Creusot, 56 Rue Clemenceau, France
Grade 1.4646, 1.4611, 1.4613
Acciai Speciali Terni
I-05100 Terni, Italy
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights other than those identified above. CEN shall not be held responsible for identifying any or
all such patent rights.---------------------- Page: 6 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
1 Scope
This document specifies the technical delivery conditions for semi-finished products, hot or cold formed
bars, rods, wire, sections and bright products of standard grades and special grades of corrosion
resistant stainless steels for general purposes.NOTE General purposes include the use of stainless steels in contact with foodstuffs.
The general technical delivery conditions specified in EN 10021 apply in addition to the specifications
of this document, unless otherwise specified in this document.This document does not apply to components manufactured by further processing of the product forms
listed above with quality characteristics altered as a result of such further processing.
2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 10021, General technical delivery conditions for steel productsEN 10027-1, Designation systems for steels - Part 1: Steel names
EN 10027-2, Designation systems for steels - Part 2: Numerical system
EN 10079:2007, Definition of steel products
prEN 10088-1:2021, Stainless steels - Part 1: List of stainless steels
EN 10163-3, Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections -
Part 3: SectionsEN 10168, Steel products - Inspection documents - List of information and description
EN 10204, Metallic products - Types of inspection documentsEN 10306, Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams
EN 10308, Non destructive testing - Ultrasonic testing of steel barsEN ISO 148-1, Metallic materials - Charpy pendulum impact test - Part 1: Test method (ISO 148-1)
EN ISO 286-1, Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes -
Part 1: Basis of tolerances, deviations and fits (ISO 286-1)EN ISO 377, Steel and steel products - Location and preparation of samples and test pieces for mechanical
testing (ISO 377)EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels - Part 2: Ferritic,
austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in media containing sulfuric acid
(ISO 3651-2)EN ISO 4885:2018, Ferrous materials - Heat treatments - Vocabulary (ISO 4885)
---------------------- Page: 7 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
EN ISO 6506-1, Metallic materials - Brinell hardness test - Part 1: Test method (ISO 6506-1)
EN ISO 6892-1, Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO
6892-1)EN ISO 6892-2, Metallic materials - Tensile testing - Part 2: Method of test at elevated temperature (ISO
6892-2)EN ISO 9443, Surface quality classes for hot-rolled bars and wire rod (ISO 9443)
EN ISO 14284, Steel and iron - Sampling and preparation of samples for the determination of chemical
composition (ISO 14284)3 Terms and definitions
For the purposes of this document, the terms and definitions regarding types of heat-treatment in
EN ISO 4885:2018 and regarding product forms in EN 10079:2007 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at https://www.electropedia.org/— ISO Online browsing platform: available at https://www.iso.org/obp
3.1
stainless steels
steels with at least 10,5 % of chromium and maximum 1,20 % of carbon
[SOURCE: EN 10020:2000, 3.2.2]
Note 1 to entry: Stainless steels are further subdivided in accordance with their main property into corrosion
resistant steels, heat resistant steels and creep resistant steels.3.2
corrosion resistant steels
steels with at least 10,5 % Cr and max. 1,20 % C if their resistance to corrosion is of primary importance
3.3general purposes
purposes other than the special purposes mentioned in the Bibliography
3.4
standard grades
grades with a relatively good availability and a wider range of application
3.5
special grades
grades for special use and/or with limited availability
4 Designation and ordering
4.1 Designation of steel grades
The steel names and steel numbers (see Tables 2 to 5) were formed in accordance with EN 10027-1 and
EN 10027-2 respectively.---------------------- Page: 8 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
A complete overview of all grades that are in this document is given in Annex A.
4.2 Designation to be used on ordering
The complete designation for ordering a product according to this document shall contain the following
information:— desired quantity;
— product form (e. g. round bars, square bars or rod);
— where an appropriate dimensional standard is available (see Table 7 and Annex D) the number of
the standard plus any choice of requirements; if there is no dimensional standard, the nominal
dimensions and tolerances required;— type of material (steel);
— number of this document;
— steel name or steel number;
— if for the relevant steel in the table for the mechanical properties more than one treatment
condition is covered, the symbol for the desired heat treatment or cold worked condition;
— desired condition (see symbols in Table 7);— if a verification of internal soundness is required, products shall be tested in accordance with
EN 10306 or EN 10308;— any additional optional tests or inspections (see 7.2.3 d);
— standard designation for a test report 2.2 or, if required, any other type of inspection document in
accordance with EN 10204 (see 7.2.1).EXAMPLE 10 t round bars according to EN 10060 of 50 mm diameter made of steel grade EN 10088–3 with
the name X5CrNi18–10 and the number 1.4301 in condition 1D (see Table 7), inspection certificate 3.1 as
specified in EN 10204:10 t round bars EN 10060 — 50
Steel EN 10088–3 — X5CrNi18–10+1D
EN 10204 — 3.1
10 t round bars EN 10060 — 50
Steel EN 10088–3-1.4301+1D
EN 10204 —3.1.
5 Classification of grades
Steels covered in this document are classified according to their structure into:
— austenitic steels,— austenitic-ferritic steels,
— ferritic steels,
---------------------- Page: 9 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
— martensitic steels,
— precipitation hardening steels.
See also prEN 10088-1:2021, Annex D.
6 Requirements
6.1 Steelmaking process
Unless otherwise agreed at the time of enquiry and order, the steelmaking and manufacturing process
for steels conforming to this document shall be at the discretion of the manufacturer.
6.2 Delivery conditionThe products shall be supplied in the delivery condition agreed at the time of enquiry and order by
reference to the conditions given in Table 7 and, where different alternatives exist, to the treatment
conditions given in Tables 8 to 19 and 25 (see also Annex B).6.3 Chemical composition
6.3.1 The chemical composition requirements given in Tables 2 to 5 apply in respect of the chemical
composition according to the cast analysis.6.3.2 The product analysis may deviate from the limiting values for the cast analysis given in Tables 2
to 5 by the values listed in Table 6.6.4 Chemical corrosion properties
Referring to resistance to intergranular corrosion as defined in EN ISO 3651-2, for austenitic, austenitic-
ferritic and ferritic stainless steels the specifications in Tables 8, 9 and 10 apply.
NOTE 1 EN ISO 3651-2 is not applicable for testing martensitic and precipitation hardening steels.
NOTE 2 The corrosion resistance of stainless steels is very dependent on the type of environment and can
therefore not always be clearly ascertained through laboratory tests. It is therefore advisable to draw on the
available experience of the use of the steels.6.5 Mechanical properties
6.5.1 The mechanical properties at room temperature as specified in Tables 8 to 12 apply for hot
worked products of every condition, condition 1U and semi-finished products excluded, for cold
processed products in condition 2D (excluding wire), and for each specified heat treatment condition.
For cold processed products of every specified condition, condition 2D and wire excluded, and each
specified heat treatment condition, the mechanical properties at room temperature as specified in
Tables 13 to 17 apply. For these products, the condition is the prime property with the mechanical
properties secondary.If by agreement at the time of ordering the products shall be supplied in a non-heat-treated condition,
the mechanical properties specified in Tables 8 to 17 shall be obtained from reference test pieces which
have received the appropriate heat treatment (simulated heat treatment).For wire, the properties as specified in Tables 18 and 19 apply.
---------------------- Page: 10 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
For bars which are intentionally cold work hardened in order to increase their tensile strength to a
specified level, the mechanical properties at room temperature as specified in Table 25 apply. For these
products, the mechanical properties are prime, with the condition a secondary property.
NOTE Austenitic steels are insensitive to brittle fracture in the solution annealed condition. Because they do
not have a pronounced transition temperature, which is characteristic of other steels, they are also useful for
application at cryogenic temperatures.A number of grades in Tables 2 to 5 are not listed or have limited information included in Tables 13 to
25. In this case, grade dimensions and corresponding mechanical properties shall be agreed upon at the
time of enquiry and order.6.5.2 The values in Tables 20 to 24 apply for the 0,2 %- and 1 %- proof strength at elevated
temperatures.6.6 Surface quality
The available surface finishes are given in Table 7. Slight surface imperfections, inherent to the
production process, are permitted. Exact requirements concerning maximum depth of acceptable
discontinuities for bars, rods and sections in the relevant conditions are given in Table 1.
Table 1 — Maximum depth of acceptable discontinuities for bars, rods and sections
Conditions Product forms Permissible depth of discontinuities Max. % of delivered weight in
excess of permissible depth ofdiscontinuities
1U, 1C, 1E, 1D Sections To be agreed upon at the time of enquiry and order on the basis of EN 10163-3.
1U, 1C, 1E, 1D Rounds and rod Unless not specified otherwise at the time of enquiry and order:
EN ISO 9443 - class A .b b b
1X , 2H , 2D Rounds - max. 0,2 mm for d ≤ 20 mm 1 %
- max. 0,01 d for 20 < d ≤ 75 mm
- max. 0,75 mm for d > 75 mm
Hexagons - max. 0,3 mm for d ≤ 15 mm 2 %
- max. 0,02 d for 15 < d ≤ 63 mm
Other bars - max. 0,3 mm for d ≤ 15 mm 4 %
- max. 0,02 d for 15 < d ≤ 63 mm
1G, 2B, 2G, 2P Rounds Technically defect free by manufacture. 0,2 %
Depth of discontinuities is understood as being the distance, measured normally to the surface, between the bottom of the
discontinuities and that surface.At the time of enquiry and order it may be agreed that the product shall be delivered with a surface being technically
defect free by manufacture. In this case, also the maximum % of delivered weight in excess of permissible depth of
discontinuities shall be agreed.For further information, e.g. roughness in conditions 2G and 2P, see Table 7.
For wires supplied in 2H condition according to Table 18 or 2B according to Table 19 the surface
quality shall be agreed upon at the time of enquiry and order.6.7 Internal soundness
The products shall be free of internal defects which would exclude them from being used for their usual
purpose. At the time of enquiry and order ultrasonic testing of H-beams with parallel flanges and IPE-
beams may be agreed in accordance with EN 10306 and ultrasonic testing of steel bars may be agreed
in accordance with EN 10308.---------------------- Page: 11 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
6.8 Formability at room temperature
Cold formability may be verified by elongation in the tensile test.
6.9 Dimensions and tolerances on dimensions and shape
The dimensions and the tolerances on dimensions shall be agreed at the time of enquiry and order, as
far as possible with reference to the dimensional standards listed in Table 7 and in Annex D.
6.10 Calculation of mass and tolerances on mass6.10.1 When calculating the nominal mass from the nominal dimensions the values given in
prEN 10088-1:2021 shall be used as a basis for the density of the steel concerned.
6.10.2 If the tolerances on mass are not specified in the dimensional standard listed in Table 7 or in
Annex D, they may be agreed at the time of enquiry and order.7 Inspection and testing
7.1 General
The appropriate process control, inspection and testing shall be carried out to ensure that the product
complies with the requirements of the order.This includes the following:
— suitable frequency of verification of the dimensions of the products;
— adequate intensity of visual examination of the surface quality of the products;
— appropriate frequency and type of test to ensure that the correct grade of steel is used.
The nature and frequency of these verifications, examinations and tests is determined in the light of the
degree of consistency that has been determined by the evidence of the quality system. In view of this,
verifications by specific tests for these requirements are not necessary unless otherwise agreed.
7.2 Agreement on tests and inspection documents7.2.1 Products complying with this document shall be ordered and delivered with one of the
inspection documents as specified in EN 10204. The type of document shall be agreed upon at the time
of enquiry and order. If the order does not contain any specification of this type, a test report 2.2 shall
be issued.7.2.2 If it is agreed to issue a test report 2.2 in accordance with EN 10204 it shall indicate the
following information:a) information groups A, B and Z of EN 10168;
b) results of the cast analysis in accordance with Tables 2 to 5 with the code numbers C71 to C92 in
EN 10168.7.2.3 If the issuing of an inspection certificate 3.1 or 3.2 according to EN 10204 has been agreed,
specific inspections according to 7.3 shall be carried out and the following information shall be given in
the inspection document with the code numbers and details required by EN 10168:a) under 7.2.2 a);
---------------------- Page: 12 ----------------------
oSIST prEN 10088-3:2022
prEN 10088-3:2021 (E)
b) under 7.2.2 b);
c) results of the mandatory tests marked in Table 26, second column, by 'm';
d) results of any optional tests or inspections agreed at the time of enquiry and order.
7.3 Specific inspection and testing7.3.1 Extent of testing
The tests to be carried out, either mandatorily (m) or by agreement (o) and the composition and size of
the test units, and the number of sample products, samples and test pieces to be taken are given in
Table 26.7.3.2 Selection and preparation of samples
7.3.2.1 Sampling and sample preparation shall be in accordance with the requirements of
EN ISO 14284 and EN ISO 377. In addition, the stipulations in 7.3.2.2 apply for the mechanical tests.
7.3.2.2 The samples for the tensile test shall be taken in accordance with Figures 1 to 3. If it has
been agreed that impact tests shall be carried out, the samples shall be taken from the same location.
The samples shall be taken from products in the delivery condition. If agreed, samples from bars may be
taken before straightening. For samples to be given a simulated heat treatment the conditions for
annealing, hardening and tempering shall be agreed.7.3.2.3 Samples for the hardness test and for the resistance to intergranular corrosion test, where
requested, shall be taken from the same locations as those for the mechanical tests.
7.4 Test methods7.4.1 The chemical analysis shall be carried out using appropriate European Standards. The choice of
a suitable physical or chemical analytical method for the analysis shall be at the discretion of the
manufacturer. The manufacturer shall declare the test method used if required.NOTE The list of available European Standards on chemical analysis is given in CEN/TR 10261.
7.4.2 The tensile test at room temperature shall be carried out in accordance with EN ISO 6892-1, this
generally being with proportional test pieces having a gauge length L = 5,65 √S . (S = cross-section of
0 0 0the parallel length). In cases of doubt and in referee testing these test pieces shall be used.
For wire of nominal diameter < 4 mm, the tensile test is made directly on the product using a gauge
length of 100 mm.The tensile strength, elongation after fracture and the 0,2 %-proof strength shall be determined. In
addition, for austenitic steels in condition 1C, 1E, 1D, 1X, 1G and 2D only, the 1 %- proof strength shall
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.