EN 10266:2003
(Main)Steel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standards
Steel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standards
This European Standard gives the symbols and definitions of terms for use in product standards for steel tubes, fittings and steel structural hollow sections.
NOTE For definitions of terms non specific to tubular products, see other relevant standards e.g. EN ISO 9000 [1].
Stahlrohre, Fittings und Hohlprofile für den Stahlbau - Symbole und Definition von Begriffen für die Verwendung in Erzeugnisnormen
Diese Europäische Norm enthält die Definition von Begriffen und Symbolen für die Verwendung in Erzeugnisnormen für Stahlrohre, Fittings und Hohlprofile für den Stahlbau.
ANMERKUNG Zur Definition von Begriffen, die nicht speziell für rohrförmige Erzeugnisse gelten, siehe andere entsprechende Normen, z. B. EN ISO 9000 [1].
Tubes en acier, accessoires et profils creux en acier pour la construction - Symboles et définitions des termes à utiliser dans les normes de produits
La présente Norme européenne indique les symboles et définitions des termes en usage dans les normes de produits traitant des tubes, raccords et profils creux de construction en acier.
NOTE Pour les définitions des termes qui ne sont pas spécifiques aux produits tubulaires, voir d'autres normes appropriées, par exemple l'EN ISO 9000.
Steel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standards
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Steel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standardsStahlrohre, Fittings und Hohlprofile für den Stahlbau - Symbole und Definition von Begriffen für die Verwendung in ErzeugnisnormenTubes en acier, accessoires et profils creux en acier pour la construction - Symboles et définitions des termes a utiliser dans les normes de produitsSteel tubes, fittings and structural hollow sections - Symbols and definitions of terms for use in product standards77.140.75Jeklene cevi in cevni profili za posebne nameneSteel pipes and tubes for specific use01.075Simboli za znakeCharacter symbols01.040.77Metalurgija (Slovarji)Metallurgy (Vocabularies)ICS:Ta slovenski standard je istoveten z:EN 10266:2003SIST EN 10266:2004en01-junij-2004SIST EN 10266:2004SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10266August 2003ICS 01.040.77; 01.075; 77.140.75English versionSteel tubes, fittings and structural hollow sections - Symbols anddefinitions of terms for use in product standardsTubes en acier, accessoires et profils creux en acier pour laconstruction - Symboles et définitions des termes à utiliserdans les normes de produitsStahlrohre, Fittings und Hohlprofile für den Stahlbau -Symbole und Definition von Begriffen für die Verwendung inErzeugnisnormenThis European Standard was approved by CEN on 27 June 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10266:2003 ESIST EN 10266:2004
Afterwelding the tube may be further processed, either hot or cold, into its final dimensions2.6butt welded tube (BW)(also known as continuous weld tube or Fretz Moon tube) tube made by a continuous process in whichdecoiled strip, welded end to end, is passed through a furnace, formed into a hollow profile and theseam weld made by further raising of the temperature of the adjacent edges (e.g. using a jet of oxygen),and pressing the edges together2.7electric welded tube (EW)tube made by pressure welding, in a continuous or non continuous process, in which strip is formed coldinto a hollow profile and the seam weld made by heating the adjacent edges through the resistance tothe passage of high or low frequency current, and pressing the edges together.
The electric currentmay be applied either by direct electrode contact or by induction.2.8high frequency welded tube (HFW)tube made by pressure welding, in a continuous or non continuous process, in which strip is formed coldinto a hollow profile and the seam weld made by heating the adjacent edges through the resistance tothe passage of a high frequency current, and pressing the edges together.
The electric current may beapplied either by direct electrode contact or by induction.SIST EN 10266:2004
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.