EN ISO 2818:2019
(Main)Plastics - Preparation of test specimens by machining (ISO 2818:2018)
Plastics - Preparation of test specimens by machining (ISO 2818:2018)
This document establishes the general principles and procedures to be followed when machining and notching test specimens from compression-moulded and injection-moulded plastics, extruded sheets, plates and partially finished or wholly finished products.
In order to establish a basis for reproducible machining and notching conditions, the following general standardized conditions are applied. It is assumed, however, that the exact procedures used are selected or specified by the relevant material specification or by the standards on the particular test methods. If sufficiently detailed procedures are not thus specified, the interested parties agree upon the conditions to be used.
Kunststoffe - Herstellung von Probekörpern durch mechanische Bearbeitung (ISO 2818:2018)
Dieses Dokument legt die allgemeinen Grundsätze und Verfahren fest, die zu befolgen sind, wenn durch mechanische und zerteilende Bearbeitung von aus durch Formpressen und Spritzgießen gefertigten Kunst¬stoffen, extrudierten Tafeln, Platten sowie Halbfertig oder Fertigerzeugnissen Probekörper hergestellt werden.
Um eine Grundlage für reproduzierbare Bedingungen für die mechanische und zerteilende Bearbeitung zu schaffen, werden die folgenden allgemeinen genormten Bedingungen angewendet. Es wird jedoch davon ausgegangen, dass die genauen angewendeten Verfahren anhand der entsprechenden Werkstoff-Spezifikation oder Normen zu den bestimmten Prüfverfahren ausgewählt oder festgelegt werden. Wenn keine ausreichend detaillierten Verfahren auf diese Weise festgelegt sind, vereinbaren die interessierten Parteien die anzuwendenden Bedingungen.
Plastiques - Préparation des éprouvettes par usinage (ISO 2818:2018)
Le présent document établit les principes et modes opératoires généraux à suivre lors de l'usinage et de la production des entailles sur les éprouvettes produites à partir de plastiques moulés par compression et par injection, de feuilles extrudées, de plaques, et de produits partiellement ou entièrement finis.
Il convient d'appliquer les conditions normalisées générales suivantes pour établir une base permettant d'obtenir des conditions reproductibles en matière d'usinage et de production d'entailles. On présume, cependant, que les modes opératoires exacts à utiliser sont choisis ou précisés dans les spécifications relatives à la matière concernée ou dans les normes afférentes aux méthodes d'essai particulières. Si les modes opératoires spécifiés ne sont pas suffisamment détaillés, il est essentiel que les parties concernées s'accordent sur les conditions à utiliser.
Polimerni materiali - Strojna priprava preskušancev (ISO 2818:2018)
Ta dokument določa splošna načela in postopke pri strojni obdelavi in
izrezovanju preskušancev iz polimernih materialov, oblikovane z vbrizgavanjem ali stiskanjem, ekstrudiranih plošč,
lamel in nedokončanih ali končnih izdelkov.
Za vzpostavitev podlage za ponovljive pogoje strojne obdelave in izrezovanja se uporabljajo naslednji splošni
standardizirani pogoji. Kljub temu se predpostavlja, da so uporabljeni postopki izbrani
ali določeni z ustrezno specifikacijo materiala ali s standardi za posamezno preskusno metodo. Če
na ta način niso določeni dovolj podrobni postopki, se zainteresirane strani dogovorijo o pogojih
uporabe.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 2818:2019
01-marec-2019
1DGRPHãþD
SIST EN ISO 2818:2000
Polimerni materiali - Strojna priprava preskušancev (ISO 2818:2018)
Plastics - Preparation of test specimens by machining (ISO 2818:2018)
Kunststoffe - Herstellung von Probekörpern durch mechanische Bearbeitung (ISO
2818:2018)
Plastiques - Préparation des éprouvettes par usinage (ISO 2818:2018)
Ta slovenski standard je istoveten z: EN ISO 2818:2019
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 2818:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 2818:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 2818:2019
EN ISO 2818
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2019
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 2818:1996
English Version
Plastics - Preparation of test specimens by machining (ISO
2818:2018)
Plastiques - Préparation des éprouvettes par usinage Kunststoffe - Herstellung von Probekörpern durch
(ISO 2818:2018) mechanische Bearbeitung (ISO 2818:2018)
This European Standard was approved by CEN on 24 December 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2818:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 2818:2019
EN ISO 2818:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 2818:2019
EN ISO 2818:2019 (E)
European foreword
This document (EN ISO 2818:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2019, and conflicting national standards shall be
withdrawn at the latest by July 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2818:1996.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 2818:2018 has been approved by CEN as EN ISO 2818:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 2818:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 2818:2019
INTERNATIONAL ISO
STANDARD 2818
Fourth edition
2018-12
Plastics — Preparation of test
specimens by machining
Plastiques — Préparation des éprouvettes par usinage
Reference number
ISO 2818:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 2818:2019
ISO 2818:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.