EN 764-2:2002

Pressure equipment - Part 2: Quantities, symbols and units

This Part of this European Standard specifies the basic quantities, symbols and units to be used for pressure equipment and assemblies addressed by the European Directive 97/23/EC.

Druckgeräte - Teil 2: Größen, Symbole und Einheiten

Diese Europäische Norm definiert die wesentlichen Größen, Symbole und Einheiten, die für Druckgeräte und deren Baugruppen gemäß der Europäischen Richtlinie 97/23/EG zu verwenden sind.

Equipements sous pression - Partie 2: Grandeurs, symboles et unités

La présente Norme européenne définit les grandeurs de base, symboles et unités à utiliser pour les équipements sous pression et ensembles concernés par la Directive européenne 97/23/CE.

Tlačna oprema - 2. del: Veličine, simboli in enote

General Information

• Status: Withdrawn
• Publication Date: 28-May-2002
• Withdrawal Date: 24-Jan-2012
• ICS: 01.060 - Quantities and units
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• Technical Committee: CEN/TC 54 - Unfired pressure vessels
• Drafting Committee: CEN/TC 54/WG 57 - H - Terminology
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 25-Jan-2012
• Completion Date: 25-Jan-2012
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN 764-2:2002 - Pressure equipment - Part 2: Quantities, symbols and units

Relations

• Replaced By: EN 764-2:2012 - Pressure equipment - Part 2: Quantities, symbols and units
• Effective Date: 01-Feb-2012

Standards Content (Sample)

SLOVENSKI STANDARD
01-november-2002
7ODþQDRSUHPDGHO9HOLþLQHVLPEROLLQHQRWH
Pressure equipment - Part 2: Quantities, symbols and units
Druckgeräte - Teil 2: Größen, Symbole und Einheiten
Equipements sous pression - Partie 2: Grandeurs, symboles et unités
Ta slovenski standard je istoveten z: EN 764-2:2002
ICS:
01.060 9HOLþLQHLQHQRWH Quantities and units
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 764-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2002
ICS 01.060; 23.020.30
English version
Pressure equipment - Part 2: Quantities, symbols and units
Equipements sous pression - Partie 2: Grandeurs, Druckgeräte - Teil 2: Größen, Symbole und Einheiten
symboles et unités
This European Standard was approved by CEN on 29 April 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 764-2:2002 E
worldwide for CEN national Members.

Contents
page
Foreword.3
1 Scope .4
2 Normative references .4
3 General.4
4 Quantities, symbols and units.4
Foreword
This document EN 764-2:2002 has been prepared by Technical Committee CEN/TC 54 "Unfired pressure vessels",
the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by November 2002, and conflicting national standards shall be withdrawn at the latest
by November 2002.
This document has been prepared under a mandate given to CEN by the European Commission (EC) and the
European Free Trade Association.
This European Standard consists of seven parts which are:
Part 1 Definitions of pressure, temperature and volume;
Part 2 Quantities, symbols and units;
Part 3 Definition of parties involved;
Part 4 Establishment of technical delivery conditions for metallic materials;
Part 5 Inspection documentation of metallic materials and compliance with the material specification;
Part 6 Operating instructions;
Part 7 Safety systems for unfired pressure equipment.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France,
...