EN 13411-1:2002
(Main)Terminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings
Terminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings
This European Standard specifies the minimum requirements for non welded general purpose steel thimbles produced from plate having dimensions in accordance with Figure 1. The thimbles are intended to be used in slings made with six or eight strand steel wire ropes from 8 mm to 60 mm diameter complying with prEN 12385-4:2001.
Reeving thimbles and solid thimbles are not covered by this standard.
The hazards covered by this standard are identified in clause 4.
Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 1: Kauschen für Anschlagseile aus Stahldrahtseilen
Diese Europäische Norm legt die Mindestanforderungen an nichtgeschweißte Stahlkauschen aus Blech für allgemeine Zwecke mit Maßen nach Bild 1 fest. Die Kauschen sind zur Verwendung bei Anschlagseilen, die aus 6- oder 8-litzigen Drahtseilen aus Stahldraht nach EN 12385-4 mit Durchmessern von 8 mm bis 60 mm hergestellt sind, bestimmt.
Durchsteck- und Vollkauschen sind nicht Gegenstand dieser Norm.
Gefährdungen, die in dieser Norm behandelt werden, sind in Abschnitt 4 angegeben.
Terminaisons pour câbles en acier - Sécurité - Partie 1: Cosses pour élingues en câbles d'acier
La présente Norme européenne spécifie les prescriptions minimales pour l'aptitude à l'emploi des cosses en acier non soudées d'usage courant, produites à partir d'une plaque dont les dimensions sont conformes à la Figure 1. Les cosses sont destinées à être utilisées en élingues composées de 6 ou 8 torons en acier, de diamètre compris entre 8 mm et 60 mm, conformément au prEN 12385-4:2001.
Les cosses à engagement simple et les cosses pleines ne sont pas couvertes par la présente norme.
L'article 4 identifie les phénomènes dangereux couverts par la présente norme.
Zaključki jeklenih žičnih vrvi - Varnost - 1. del: Vrvna srca za obesne zanke jeklenih žičnih vrvi
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Endverbindungen für Drahtseile aus Stahldraht - Sicherheit - Teil 1: Kauschen für Anschlagseile aus StahldrahtseilenTerminaisons pour câbles en acier - Sécurité - Partie 1: Cosses pour élingues en câbles d'acierTerminations for steel wire ropes - Safety - Part 1: Thimbles for steel wire rope slings77.140.99Drugi železni in jekleni izdelkiOther iron and steel products53.020.30Pribor za dvigalno opremoAccessories for lifting equipmentICS:Ta slovenski standard je istoveten z:EN 13411-1:2002SIST EN 13411-1:2003en01-maj-2003SIST EN 13411-1:2003SLOVENSKI
STANDARD
SIST EN 13411-1:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13411-1February 2002ICS 21.060.70; 53.020.30English versionTerminations for steel wire ropes - Safety - Part 1: Thimbles forsteel wire rope slingsTerminaisons pour câbles en acier - Sécurité - Partie 1:Cosses pour élingues en câbles d'acierEndverbindungen für Drahtseile aus Stahldraht - Sicherheit- Teil 1: Kauschen für Anschlagseile aus DrahtseilenThis European Standard was approved by CEN on 11 November 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13411-1:2002 ESIST EN 13411-1:2003
EN 13411-1:2002 (E)2ContentspageForeword3Introduction41Scope42Normative references43Terms and definitions54Hazards55Safety requirements and/or measures56Verification77
Certificate8Annex ZA (informative)
Relationship of this document with EC Directives9Bibliography10SIST EN 13411-1:2003
EN 13411-1:2002 (E)3ForewordThis document EN 13411-1:2002 has been prepared by Technical Committee CEN/TC 168 "Chains,ropes, webbing slings and accessories" the secretariat of which is held by BSI.This European Standard shall be given the status of a national standard, either by publication of anidentical text or by endorsement, at the latest by August 2002, and conflicting national standards shall bewithdrawn at the latest by August 2002.This document has been prepared under a mandate given to CEN by the European Commission and theEuropean Free Trade Association, and supports essential requirements of EC Directive(s).For the relationship with EC Directives, see informative annex ZA which is an integral part of thisdocument.The other Parts of this European Standard are:Part 2: Splicing of eyes for steel wire rope slingsPart 3: Ferrule secured eyesPart 4: Metal and resin socketingPart 5: Wire rope grips for eyesPart 6: Asymmetric wedge socket clevisPart 7: Symmetric wedge socket clevisThis is the first edition of this part of this European Standard.According to the CEN/CENELEC Internal Regulations, the national standards organizations of thefollowing countries are bound to implement this European Standard: Austria, Belgium, Czech Republic,Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 13411-1:2003
EN 13411-1:2002 (E)4IntroductionThis European Standard has been prepared to provide a means of conforming with the essential safetyrequirements of the Machinery Directive and associated EFTA regulations.Purchasers ordering to this standard are advised to specify in their purchasing contract that the supplieroperates a certified quality assurance system applicable to the relevant part of this standard(e.g. EN ISO 9001) to ensure themselves that products claiming to comply consistently achieve therequired level of quality.While producing this standard it was assumed that negotiation occurs between the manufacturer and theuser to decide whether the thimble shall have a pointed or truncated end and whether zinc coating isrequired.1
ScopeThis European Standard specifies the minimum requirements for non welded general purpose steelthimbles produced from plate having dimensions in accordance with Figure 1. The thimbles are intendedto be used in slings made with six or eight strand steel wire ropes from 8 mm to 60 mm diametercomplying with EN 12385-4.Reeving thimbles and solid thimbles are not covered by this standard.The hazards covered by this standard are identified in clause 4.2
Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications.These normative references are cited at the appropriate places in the text, and the publications are listedhereafter. For dated references, subsequent amendments to or revisions of any of these publicationsapply to this European Standard only when incorporated in it by amendment or revision. For undatedreferences the latest edition of the publication referred to applies (including amendments).EN 292-2:1991/A1:1995, Safety of machinery - Basic concepts, general principles for design - Part 2:Technical principles and specifications (Amendment 1:1995).EN 1050:1996, Safety of machinery - Principles for risk assessment.EN 10025, Specification for hot rolled products of non-alloy structural steels - Technical deliveryconditions (includes amendment A1:1993).EN 12385-1:2002, Steel wire ropes – Safety - Part 1: General requirements.prEN 12385-2, Steel wire ropes – Safety - Part 2: Definitions, designation and classification.EN 12385-4:20
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.