EN 10314:2002

Method for the derivation of minimum values of proof strength of steel at elevated temperatures

This European Standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures.
However, this standard does not specify a verification procedure.

Verfahren zur Ableitung von Mindestwerten der Dehngrenze von Stahl bei erhöhten Temperaturen

Diese Europäische Norm legt ein Verfahren zur Ableitung der Mindestwerte der Dehngrenze von Stählen bei erhöhter Temperatur fest.
Diese Norm legt aber kein Verifizierungsverfahren fest.

Méthode de dérivation des valeurs minimales de la limite conventionnelle d'élasticité des aciers à températures élevées

La présente Norme européenne spécifie une méthode de dérivation des valeurs minimales de la limite conventionnelle d'élasticité des aciers à des températures élevées.
Cependant, la présente norme ne spécifie pas une méthode de vérification.

Metoda za izpeljavo najmanjših vrednosti napetosti tečenja jekel pri povišanih temperaturah

General Information

• Status: Withdrawn
• Publication Date: 19-Nov-2002
• Withdrawal Date: 31-May-2016
• ICS: 77.140.30 - Steels for pressure purposes
• Technical Committee: ECISS/TC 107 - Steels for pressure purposes
• Drafting Committee: ECISS/TC 22 - Steels for pressure purposes - Qualities
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 01-Jun-2016
• Ref Project: SIST EN 10314:2003 - Method for the derivation of minimum values of proof strength of steel at elevated temperatures

Relations

• Replaces: ENV 22605-3:1991 - Steel products for pressure purposes - Derivation and verification of elevated temperature properties - Part 3: An alternative procedure for deriving the elevated temperature yield or proof stress properties when data are limited (ISO 2605-3:1985)
• Effective Date: 22-Dec-2008
• Replaces: ENV 22605-1:1991 - Steel products for pressure purposes - Derivation and verification of elevated temperature properties - Part 1: Yield or proof stress of carbon and low alloy steel products (ISO 2605-1:1976)
• Effective Date: 22-Dec-2008
• Replaces: ENV 22605-2:1991 - Steel products for pressure purposes - Derivation and verification of elevated temperature properties - Part 2: Proof stress of austenitic steel products (ISO 2605-2:1976)
• Effective Date: 22-Dec-2008
• Replaced By: EN 10314:2016 - Method for the derivation of minimum values of proof strength of steel at elevated temperatures
• Effective Date: 28-Nov-2012

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WHPSHUDWXUDKVerfahren zur Ableitung von Mindestwerten der Dehngrenze von Stahl bei erhöhten TemperaturenMéthode de dérivation des valeurs minimales de la limite conventionnelle d'élasticité des aciers a températures élevéesMethod for the derivation of minimum values of proof strength of steel at elevated temperatures77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:Ta slovenski standard je istoveten z:EN 10314:2002SIST EN 10314:2003en01-april-2003SIST EN 10314:2003SLOVENSKI
STANDARDSIST ENV 22605-3:1997SIST ENV 22605-2:1997SIST ENV 22605-1:19971DGRPHãþD



SIST EN 10314:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10314November 2002ICS 77.140.30Supersedes ENV 22605-1:1991, ENV 22605-2:1991 andENV 22605-3:1991English versionMethod for the derivation of minimum values of proof strength ofsteel at elevated temperaturesMéthode de dérivation des valeurs minimales de la limiteconventionnelle d'élasticité des aciers à températuresélevéesVerfahren zur Ableitung von Mindestwerten derDehngrenze von Stahl bei erhöhten TemperaturenThis European Standard was approved by CEN on 19 August 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10314:2002 ESIST EN 10314:2003



EN 10314:2002 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.54Symbols.65Method.65.1 Input data groups.65.2 Ratio values.65.3 Minimum proof strength values.76Application of the method.86.1 Representative data groups.86.2 Number of data.86.3 Consistency of data.86.4 Result.9Bibliography.10SIST EN 10314:2003



EN 10314:2002 (E)3ForewordThis document (EN 10314:2002) has been prepared by the ECISS/TC 22 "Steels for pressurepurposes - Qualities", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publicationof an identical text or by endorsement, at the latest by May 2003, and conflicting nationalstandards shall be
...