EN ISO 1797-2:1995
(Main)Dental rotary equipment - Shanks - Part 2: Shanks made of plastics (ISO 1797-2:1992)
Dental rotary equipment - Shanks - Part 2: Shanks made of plastics (ISO 1797-2:1992)
Specifies four types. Gives measurement methods for the verification of dimensions. Includes quality control requirements.
Zahnärztliche rotierende Instrumente - Schäfte - Teil 2: Schäfte aus Kunststoff (ISO 1797-2:1992)
Dieser Teil der ISO enthält Festlegungen für Schäfte von zahnärztlich rotierenden Instrumenten, die aus Kunststoffmaterialien hergestellt werden, und legt Verfahren zur Überprüfung der Maße fest. Um einen hohen Qualitätstandard sicherzustellen, wurde eine Anforderung an die Qualitätskontrolle aufgenommen. Unterpunkte 4.6 und 4.7 gelten nicht für Wegwerfinstrumente (Einmalgebrauch). Schäfte aus Kunststoffmaterial sind für Geschwindigkeiten von weniger als 5000 Umdrehungen/Minute entworfen.
Instruments rotatifs dentaires - Queues - Partie 2: Queues en matières plastiques (ISO 1797-2:1992)
La présente partie de l'ISO 1797 prescrit des spécifications pour les queues d'instruments rotatifs dentaires en matières plastiques ainsi que des méthodes de mesurage pour la vérification des dimensions. Une prescription de qualité est ajoutée afin d'assurer un haut niveau de qualité. Les paragraphes 4.6 et 4.7 ne s'appliquent pas aux instruments non réutilisables. Les queues en matières plastiques sont conçues pour être utilisées sous des vitesses inférieures à 5 000 tr/min.
Dental rotary equipment - Shanks - Part 2: Shanks made of plastics (ISO 1797-2:1992)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2000
Dental rotary equipment - Shanks - Part 2: Shanks made of plastics (ISO 1797-
2:1992)
Dental rotary equipment - Shanks - Part 2: Shanks made of plastics (ISO 1797-2:1992)
Zahnärztliche rotierende Instrumente - Schäfte - Teil 2: Schäfte aus Kunststoff (ISO 1797
-2:1992)
Instruments rotatifs dentaires - Queues - Partie 2: Queues en matieres plastiques (ISO
1797-2:1992)
Ta slovenski standard je istoveten z: EN ISO 1797-2:1995
ICS:
11.060.25 =RERWHKQLþQLLQVWUXPHQWL Dental instruments
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL
STANDARD 1797-2
First edition
1992-02-15
--
__-________ -__-~- _-- ---_-- _-_-_---_----.--- ---. - -__- -.__ -___-___ __I____.___-_-_
Dental rotary instruments - Shanks -
Part 2:
Shanks made of plastics
Instruments rotatifs dentaires - Queues -
Partie 2: Queues en matibes plastiques
_~ ____ ~ --___ -----1---- I___._._ ---_------- ~----~__
e_-.---
-- --
Reference number
~ -_-_
--__-
-_. - ._- ._._.
ISO 1797-2: 1992(E)
ISO 179702:1992(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the
work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on -all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an Inter-
national Standard requires approval by at least 75 % of the member
bodies casting a vote.
International Standard ISO 1797-2 was prepared by Technical Committee
ISO/TC 106, Dentistry, Sub-Committee SC 4, Dental instruments.
This fit-st edition of ISO 1797-2, together with ISO 1797-1, cancel and
replace the first edition of ISO 1797 published in 1985, of which they
constitute a technical revision.
ISO 1797 consists of the following Parts, under the qeneral title Dental
L
rotary instruments - Shanks:
- Part 1: Shanks made of metals
- Part 2: Shanks made of plastics
0 ISO 1992
All rights reserved. No part of this publication may be reproduced or utillzed in any form
or by any means, electronie or mechanical, lncluding photocopying and microfilm, without
Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-1211 Geneve 20 l Switzerland
Prlnted in Switzerland
ii
ISO 1797=2:1992(E)
Introduction
This International Standard is one of a series of basic Standards on
dental rotary instruments and constitutes an important link between the
Standards on dental rotary instruments and those on dental handpieces.
. . .
Ill
This page intentionally left blank
INTERNATIONAL STANDARD ISO 1797=2:1992(E)
Dental rotary instruments - Shanks -
Part 2:
Shanks made of plastics
(stylus) instruments of consecutive profile trans-
1 Scope
formation - Contact Profile mefers, System M.
This part of ISO 1797 specifies shanks of dental ro-
ISO 3630-1 :w’), Dental root-canal instruments -
tary instruments made of plastics materials and
Part 1: Files, r-eamers, barbed hroaches, rasps, Paste
gives measurement rnethods for the verification of
carriers, explorers and cotton broaches.
the dimensions. A quality requirement is added in
Order to ensure a high quality level.
ISO 3630-2:1986, Dental root canal instruments -
Sub
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.