EN 754-6:2008

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form

This document specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn hexagonal bars having widths across flats in the range from 3 mm up to and including 80 mm.
The temper designations used in this part are according to EN 515.

Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 6: Sechskantstangen, Grenzabmaße und Formtoleranzen

Dieses Dokument legt die Grenzabmaße und Formtoleranzen für gezogene Sechskantstangen aus Aluminium
und Aluminiumlegierungen mit einer Schlüsselweite von 3 mm bis 80 mm fest.
Die in diesem Dokument verwendeten Bezeichnungen der Werkstoffzustände entsprechen EN 515.

Aluminium et alliages d'aluminium - Barres et tubes étirés - Partie 6: Barres hexagonales, tolérances sur dimensions et forme

Le présent document spécifie les tolérances sur dimensions et formes des barres hexagonales étirées en aluminium et alliages d’aluminium de largeur sur plats comprise entre 3 mm et 80 mm inclus.
La désignation des états métallurgiques utilisés dans cette partie est conforme à l’EN 515.

Aluminij in aluminijeve zlitine - Hladno vlečene palice/drogovi in cevi - 6. del: Palice s šesterokotnim prerezom, tolerance mer in oblike

General Information

• Status: Published
• Publication Date: 18-Mar-2008
• ICS: 77.150.10 - Aluminium products
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 5 - Extruded and drawn products
• Current Stage: 9020 - Submission to 2 Year Review Enquiry - Review Enquiry
• Start Date: 15-Jul-2024
• Completion Date: 15-Jul-2024
• Ref Project: SIST EN 754-6:2008 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form

Relations

• Replaces: EN 754-6:1995 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars, tolerances on dimensions and form
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2008
1DGRPHãþD
SIST EN 754-6:1998
$OXPLQLMLQDOXPLQLMHYH]OLWLQH+ODGQRYOHþHQHSDOLFHGURJRYLLQFHYLGHO
3DOLFHVãHVWHURNRWQLPSUHUH]RPWROHUDQFHPHULQREOLNH
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars,
tolerances on dimensions and form
Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 6:
Sechskantstangen, Grenzabmaße und Formtoleranzen
Aluminium et alliages d'aluminium - Barres et tubes étirés - Partie 6 : Barres
hexagonales, tolérances sur dimensions et forme
Ta slovenski standard je istoveten z: EN 754-6:2008
ICS:
77.150.10
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 754-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2008
ICS 77.150.10 Supersedes EN 754-6:1995
English Version
Aluminium and aluminium alloys - Cold drawn rod/bar and tube -
Part 6: Hexagonal bars, tolerances on dimensions and form
Aluminium et alliages d'aluminium - Barres et tubes étirés - Aluminium und Aluminiumlegierungen - Gezogene Stangen
Partie 6: Barres hexagonales, tolérances sur dimensions et und Rohre - Teil 6: Sechskantstangen, Grenzabmaße und
forme Formtoleranzen
This European Standard was approved by CEN on 10 February 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 754-6:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope.4
2 Tolerances on dimensions .4
2.1 Width across flats.4
2.2 Corner radii.4
2.3 Length.5
2.4 Squareness of cut ends .5
3 Tolerances on form.5
3.1 Straightness.5
3.2 Convexity - Concavity.6
3.3 Twist.6
Bibliography .8

Foreword
This document (EN 754-6:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall
be withdrawn at the latest by September 2008.
This document supersedes EN 754-6:1995.
Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 5 "Extruded
and drawn products" to revise EN 754-6:1995
The following technical modifications have been introduced during the revision:
 Only editorial changes to bring this part in line with the other parts of EN 754
EN 754 comprises the following parts under the general title "Aluminium and aluminium alloys — Cold
drawn rod/bar and tube ":
 Part 1: Technical conditions for inspection and del
...