EN IEC 60317-27-3:2019

Specifications for particular types of winding wires - Part 27-3: Paper tape covered rectangular copper wire

IEC 60317-27-3:2019 specifies the requirements of paper tape covered rectangular copper winding wires. This covering consists of two or more layers of paper tape and is primarily intended for winding coils for oil immersed transformers. The range of nominal conductor dimensions covered by this document is - width: min. 2,0 mm max. 31,5 mm; - thickness: min. 0,80 mm max. 10,0 mm. The paper tapes included in this document are restricted to those specified in IEC 60554-1 and IEC 60554-3-5. Keywords: paper tape covered rectangular copper winding wires

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 27-3: Flachdrähte aus Kupfer, papierisoliert

Spécifications pour types particuliers de fils de bobinage - Partie 27-3: Fil de section rectangulaire en cuivre recouvert de ruban papier

IEC 60317-27-3:2019 spécifie les exigences relatives au fil de bobinage de section rectangulaire en cuivre recouvert de ruban papier. Ce revêtement est constitué d'au moins deux couches de ruban papier et est essentiellement destiné au bobinage pour les transformateurs immergés dans l'huile La gamme des dimensions nominales des conducteurs couvertes par le présent document est: – largeur: min. 2,0 mm max. 31,5 mm; – épaisseur: min. 0,80 mm max. 10,0 mm. Les rubans papier inclus dans le présent document sont limités à ceux qui sont spécifiés dans l'IEC 60554-1 et l’IEC 60554-3-5. Mots clés: fil de bobinage de section rectangulaire en cuivre recouvert de ruban papier

Specifikacije za posebne vrste navijalnih žic - 27-3. del: S papirnim trakom ovita pravokotna bakrena žica (IEC 60317-27-3:2019)

Ta dokument določa zahteve za pravokotne bakrene navijalne žice, ovite s papirnim trakom. Ta ovoj je sestavljen iz dveh ali več plasti papirnega traku in je prvotno namenjen za navijanje tuljav za oljne transformatorje. Razpon nazivnih mer prevodnika, ki ga zajema ta dokument, je: – širina: najm. 2,0 mm, najv. 31,5 mm; – debelina: najm. 0,80 mm, najv. 10,0 mm. Papirni trakovi, vključeni v tem dokumentu, so omejeni na tiste, ki so določeni v standardih IEC 60554-1 in IEC 60554-3-5.

General Information

• Status: Published
• Publication Date: 19-Dec-2019
• Withdrawal Date: 17-Dec-2022
• ICS: 29.060.10 - Wires
• Technical Committee: CLC/TC 55 - Winding wires
• Drafting Committee: IEC/TC 55 - IEC_TC_55
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 20-Dec-2019
• Completion Date: 20-Dec-2019
• Ref Project: SIST EN IEC 60317-27-3:2020 - Specifications for particular types of winding wires - Part 27-3: Paper tape covered rectangular copper wire (IEC 60317-27-3:2019)

Relations

• Replaces: EN 60317-27:2014 - Specifications for particular types of winding wires - Part 27: Paper tape covered rectangular copper wire
• Effective Date: 24-Dec-2019
• Amended By: EN IEC 60317-27-3:2019/prA1:2023 - Specifications for particular types of winding wires - Part 27-3: Paper tape covered rectangular copper wire
• Effective Date: 14-Feb-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN IEC 60317-27-3:2020
01-marec-2020
Nadomešča:
SIST EN 60317-27:2014
Specifikacije za posebne vrste navijalnih žic - 27-3. del: S papirnim trakom ovita
pravokotna bakrena žica (IEC 60317-27-3:2019)
Specifications for particular types of winding wires - Part 27-3: Paper tape covered
rectangular copper wire (IEC 60317-27-3:2019)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten – Teil 27-3:
Flachdrähte aus Kupfer, papierisoliert (IEC 60317-27-3:2019)
Spécifications pour types particuliers de fils de bobinage - Partie 27-3: Fil de section
rectangulaire en cuivre recouvert de ruban papier (IEC 60317-27-3:2019)
Ta slovenski standard je istoveten z: EN IEC 60317-27-3:2019
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
SIST EN IEC 60317-27-3:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN IEC 60317-27-3:2020

---------------------- Page: 2 ----------------------
SIST EN IEC 60317-27-3:2020


EUROPEAN STANDARD EN IEC 60317-27-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
December 2019
ICS 29.060.10 Supersedes EN 60317-27:2014 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 27-3:
Paper tape covered rectangular copper wire
(IEC 60317-27-3:2019)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 27-3: Fil de section rectangulaire en cuivre recouvert Wickeldrähten - Teil 27-3: Flachdrähte aus Kupfer,
de ruban papier papierisoliert
(IEC 60317-27-3:2019) (IEC 60317-27-3:2019)
This European Standard was approved by CENELEC on 2019-12-18. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.


European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN IEC 60317-27-3:2019 E

---------------------- Page: 3 ----------------------
SIST EN IEC 60317-27-3:2020
EN IEC 60317-27-3:2019 (E)
European foreword
The text of document 55/1801/FDIS, future edition 1 of IEC 60317-27-3, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-27-3:2019.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2020-09-18
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022-12-18
document have to be withdrawn

This document supersedes EN 60317-27:2014 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 60317-27-3:2019 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60264 (series) NOTE Harmonized as EN 60264 (series)
IEC 60317 (series) NOTE Harmonized as EN 60317 (series)
IEC 60851 (series) NOTE Harmonized as EN 60851 (series)
ISO 6892-1 NOTE Harmonized as EN ISO 6892-1

2

---------------------- Page: 4 ----------------------
SIST EN IEC 60317-27-3:2020
EN IEC 60317-27-3:2019 (E)
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publication
...