Basic principles for graphical symbols for use on equipment - Part 2: Form and use of arrows
EN following parallel vote
Allgemeine Grundlagen für Graphische Symbole auf Einrichtungen - Teil 2: Form und Anwendung von Pfeilen
Principes de base pour les symboles graphiques utilisables sur le matériel - Partie 2: Forme et utilisation des flèches
Osnovna načela grafičnih simbolov za rabo na opremi - 2. del: Oblika in uporaba puščic (ISO 80416-2:2001)
Standards Content (sample)
SLOVENSKI SIST EN 80416-2:2004
Osnovna načela grafičnih simbolov za rabo na opremi - 2. del: Oblika in
uporaba puščic (ISO 80416-2:2001)
Basic principles for graphical symbols for use on equipment - Part 2: Form and useof arrows (ISO 80416-2:2001)
ICS 01.080.20 Referenčna številka
SIST EN 80416-2:2004(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 80416-2
EUROPÄISCHE NORM August 2001
Basic principles for graphical symbols for use on equipment
Part 2: Form and use of arrows
Principes de base pour les symboles Allgemeine Grundlagen für Graphische
graphiques utilisables sur le matériel Symbole auf Einrichtungen
Part 2: Forme et utilisation des flèches Teil 2: Form und Anwendung von Pfeilen
(ISO 80416-2:2001) (ISO 80416-2:2001)
This European Standard was approved by CENELEC on 2001-07-03. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,Portugal, Spain, Sweden, Switzerland and United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 80416-2:2001 E
---------------------- Page: 2 ----------------------
EN 80416-2:2001 - 2 -
The text of document 3C/601/FDIS, future edition 1 of ISO 80416-2, prepared by ISO Technical
committee 145, Graphical Symbols, was submitted to the IEC-CENELEC parallel vote and wasapproved by CENELEC as EN 80416-2 on 2001-07-03.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2002-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2004-07-01
Annexes designated "normative" are part of the body of the standard.
In this standard, annexes A and ZA are normative.
Annex ZA has been added by CENELEC.
The text of the International Standard ISO 80416-2:2001 was approved by CENELEC as a EuropeanStandard without any modification.
---------------------- Page: 3 ----------------------
- 3 - EN 80416-2:2001
Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard only when incorporated in it by amendment or
revision. For undated references the latest edition of the publication referred to applies (includingamendments).
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevantEN/HD applies.
Publication Year Title EN/HD Year
IEC 80416-1 2001 Basic principles for graphical symbols EN 80416-1 2001
for use on equipment
Part 1: Creation of symbol originals
IEC 60417 Series Graphical symbols for use on equipment EN 60417 Series
ISO 7000 Graphical symbols for use on equipment--
- Index and synopsis
---------------------- Page: 4 ----------------------
Basic principles for graphical symbols for
Form and use of arrows
Principes debasepour lessymboles graphiquesutilisablessur lematériel—
Partie 2: Forme et utilisation des flèches
---------------------- Page: 5 ----------------------
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in thisarea.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member bodyin the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
Printed in Switzerland
ii © ISO 2001 – All rights reserved
---------------------- Page: 6 ----------------------
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International ElectrotechnicalCommission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of ISO 80416-2 may be the subject of patent rights.ISO shall not be held responsible for identifying any or all such patent rights.
In order to collect all requirements concerning basic principles for graphical symbols for use on equipment,
ISO/TC 145, Graphical symbols, and IEC/TC 3, Documentation and graphical symbols, agreed to prepare jointly all
parts of this International Standard and to publish them under the general number 80416. For each of the individual
parts of this series, only one of the two organizations is responsible. Meanwhile, the technical committees have
agreed that no modification will be made to International Standard 80416 except bymutual agreement.
International Standard ISO 80416-2 was accordingly prepared jointly by Technical Committee ISO/TC 145,
Graphical symbols, and Technical Committee IEC/TC 3, Documentation and graphical symbols. The draft wascirculated for voting to the national bodies of both ISO and IEC.
This first edition of ISO 80416-2 cancels and replaces I