EN 62192:2009
(Main)Live working - Insulating ropes
Live working - Insulating ropes
IEC 62192:2009 covers insulating ropes that are utilized during live working procedures in contact with parts of installations operating at voltages up to and including 800 kV r.m.s. Insulating ropes for live working procedure under rain and/or d.c. conditions are not covered by this standard.
Arbeiten unter Spannung - Isolierende Seile
Travaux sous tension - Cordes isolantes
La CEI 62192:2009 est applicable aux cordes isolantes utilisées lors de travaux sous tension et faisant contact avec des parties des installations exploitées à des tensions jusques et y compris 800 kV efficace. La présente norme ne s'applique pas aux cordes isolantes utilisées lors de travaux sous tension réalisés sous pluie et/ou sur des installations à courant continu.
Delo pod napetostjo - Izolacijske vrvi (IEC 62192:2009)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2009
Delo pod napetostjo - Izolacijske vrvi (IEC 62192:2009)
Live working - Insulating ropes
Arbeiten unter Spannung – Isolierende Seile
Travaux sous tension - Cordes isolantes
Ta slovenski standard je istoveten z: EN 62192:2009
ICS:
13.260 9DUVWYRSUHGHOHNWULþQLP Protection against electric
XGDURP'HORSRGQDSHWRVWMR shock. Live working
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 62192
NORME EUROPÉENNE
June 2009
EUROPÄISCHE NORM
ICS 13.260; 29.240.20; 29.260.99
English version
Live working -
Insulating ropes
(IEC 62192:2009)
Travaux sous tension - Arbeiten unter Spannung -
Cordes isolantes Isolierende Seile
(CEI 62192:2009) (IEC 62192:2009)
This European Standard was approved by CENELEC on 2009-05-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62192:2009 E
Foreword
The text of document 78/773/FDIS, future edition 1 of IEC 62192, prepared by IEC TC 78, Live working,
was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62192 on
2009-05-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-02-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-05-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 62192:2009 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60743 + A1 NOTE Harmonized as EN 60743:2001 + A1:2008 (not modified).
__________
– 3 – EN 62192:2009
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60060-1 - High-voltage test techniques - HD 588.1 S1 1991
Part 1: General definitions and test
requirements
IEC 60212 1971 Standard conditions for use prior to and HD 437 S1 1984
during the testing of solid electrical insulating
materials
IEC 60417 Data- Graphical symbols for use on equipment - -
base
IEC 61318 2007 Live working - Conformity assessment EN 61318 2008
applicable to tools, devices and equipment
1) 2)
IEC 61477 - Live working - Minimum requirements for the EN 61477 2009
utilization of tools, devices and equipment
1) 2)
ISO 2307 - Fibre ropes - Determination of certain EN ISO 2307 2005
physical and mechanical properties
1)
Undated reference.
2)
Valid edition at date of issue.
IEC 62192 ®
Edition 1.0 2009-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Live working – Insulating ropes
Travaux sous tension – Cordes isolantes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
S
CODE PRIX
ICS 13.260; 29.240.20; 29.260.99 ISBN 2-8318-1030-2
– 2 – 62192 © IEC:2009
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms and definitions .6
4 Requirements .7
4.1 Physical and dimensional .7
4.1.1 Physical.7
4.1.2 Dimensional .7
4.2 Electrical .7
4.3 Mechanical.7
4.4 Marking .8
4.5 Instructions for use and care .8
5 Tests .9
5.1 General .9
5.2 Atmospheric conditions .9
5.3 Visual verification and dimensional checking .9
5.3.1 Visual verification .9
5.3.2 Dimensional check .9
5.4 Electrical tests.9
5.4.1 Leakage current under dry conditions .9
5.4.2 Tests after water conditioning.13
5.5 Mechanical tests .14
5.5.1 Water absorption .14
5.5.2 Capillary.14
5.5.3 Elongation and creep.14
5.6 Durability of marking .15
5.7 Verification of the required instructions for use.15
6 Conformity assessment of insulating ropes having completed the production phase .15
7 Modifications .15
Annex A (normative) Suitable for live working; double triangle (IEC 60417-5216
(2002-10)).16
Annex B (normative) Chronology of type tests .17
Annex C (normative) Classification of defects .18
Annex D (informative) Recommendations for in-service care and periodic testing .19
Bibliography.21
Figure 1 – Example of test set up to measure leakage current .10
Figure 2 – Electrode arrangement on rope test piece .12
Table B.1 – Chronology of type tests .
Table C.1 – Classification of defects and associated requirements and tests .18
62192 © IEC:2009 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LIVE WORKING –
INSULATING ROPES
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62192 has been prepared by technical committee 78: Live
working.
The text of this standard is based on the following documents:
FDIS Report on voting
78/773/FDIS 78/787/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
– 4 – 62192 © IEC:2009
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
62192 © IEC:2009 – 5 –
INTRODUCTION
Insulating ropes designed and manufactured according to this s
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.