EN 61318:2008

Live working - Conformity assessment applicable to tools, devices and equipment

Provides elements for product conformity assessment. Critical defects on tools, devices and equipment for live working are not acceptable. Major defects on tools, devices and equipment for live working are likely to result in failure or in a significant reduction of functionality, while minor defects do not reduce significantly the functionality. This standard defines assessment methods for products having completed production phase to assure that they conform to the requirements of the corresponding product standard. It is to be used in conjunction with live working corresponding product standards. The following elements are not covered by the present document, but are included in each product standard: - type tests; - provisions and description for sampling and routine tests; - the identification and classification of the corresponding defects resulting from a risk analysis. This third edition cancels and replaces the first edition which was issued as a technical report in 1994 with its Corrigendum 1 (2000), and the second edition, withdrawn, which was issued as a standard in 2003. It includes the following significant technical changes from the previous edition: - change of the purpose of the document from a support to standard writers to a standard for assessing the conformity by testing of products having completed the production phase; - clarification of the definitions of critical, major and minor defects; - specification of ISO 2859 for the manufacturers to define the appropriate sampling plans; - review of the acceptance quality limit (AQL) to specify lower limits.

Arbeiten unter Spannung – Konformitätsbewertung anwendbar auf Werkzeuge, Geräte und Ausrüstungen

Travaux sous tension - Evaluation de la conformité applicable à l'outillage, au matériel et aux dispositifs

Fournit des éléments destinés à l'évaluation de la conformité de produit. Les défauts critiques sur l'outillage, le matériel et les dispositifs pour les travaux sous tension ne sont pas acceptables. Les défauts majeurs sur l'outillage, le matériel et les dispositifs pour les travaux sous tension sont susceptibles de provoquer une défaillance ou de réduire d'une manière appréciable la fonctionnalité du produit tandis que les défauts mineurs ne réduisent pas d'une manière appréciable la fonctionnalité du produit. La présente norme définit des méthodes d'évaluation des produits finis issus de production pour s'assurer qu'ils se conforment aux exigences de la norme de produit correspondante. Elle est conçue pour être utilisée conjointement avec les normes de produit pour les travaux sous tension. Les éléments suivants ne sont pas couverts par le présent document mais sont inclus dans chaque norme de produit: - les essais de type; - les dispositions et description des essais de prélèvement et des essais individuels de série; - l'identification et la classification des défauts correspondants et qui résultent d'une analyse du risque. Cette troisième édition annule et remplace la première édition parue sous forme de rapport technique en 1994 avec son Corrigendum 1 (2000), et la seconde édition publiée en 2003, retirée. Elle inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - le changement de propos du document qui d'un support aux rédacteurs de normes devient une norme pour évaluer par des essais la conformité des produits issus de production; - la clarification des définitions des défauts critiques, majeurs et mineurs; - la spécification de l'ISO 2859 pour la détermination par les fabricants des plans d'échantillonnage appropriés; - la revue du niveau de qualité acceptable (NQA) pour spécifier des valeurs plus faibles.

Delo pod napetostjo - Ugotavljanje skladnosti za orodja, naprave in opremo

General Information

• Status: Published
• Publication Date: 28-May-2008
• Withdrawal Date: 30-Apr-2013
• ICS: 13.260 - Protection against electric shock. Live working
• ICS: 29.240.20 - Power transmission and distribution lines
• ICS: 29.260.99 - Other electrical equipment for working in special conditions
• Technical Committee: CLC/TC 78 - Equipment and tools for live working
• Drafting Committee: IEC/TC 78 - IEC_TC_78
• Parallel Committee: IEC/TC 78 - IEC_TC_78
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 29-May-2008
• Completion Date: 29-May-2008
• Ref Project: SIST EN 61318:2008 - Live working - Conformity assessment applicable to tools, devices and equipment

Relations

• Replaced By: EN IEC 61318:2021 - Live working - Methods for assessment of defects and verification of performance applicable to tools, devices and equipment
• Effective Date: 31-Aug-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61318:2008
01-september-2008
Delo pod napetostjo - Ugotavljanje skladnosti za orodja, naprave in opremo
Live working - Conformity assessment applicable to tools, devices and equipment
Travaux sous tension - Evaluation de la conformit applicable l'outillage, au matriel et aux
dispositifs
Ta slovenski standard je istoveten z: EN 61318:2008
ICS:
13.260 9DUVWYRSUHGHOHNWULþQLP Protection against electric
XGDURP'HORSRGQDSHWRVWMR shock. Live working
SIST EN 61318:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61318:2008

---------------------- Page: 2 ----------------------

SIST EN 61318:2008

EUROPEAN STANDARD
EN 61318

NORME EUROPÉENNE
May 2008
EUROPÄISCHE NORM

ICS 13.260; 29.240.20; 29.260.99


English version


Live working -
Conformity assessment applicable to tools, devices and equipment
(IEC 61318:2007)


Travaux sous tension -  Arbeiten unter Spannung –
Evaluation de la conformité applicable Konformitätsbewertung anwendbar
à l'outillage, au matériel et aux dispositifs auf Werkzeuge, Geräte und Ausrüstungen
(CEI 61318:2007) (IEC 61318:2007)




This European Standard was approved by CENELEC on 2008-04-16. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61318:2008 E

---------------------- Page: 3 ----------------------

SIST EN 61318:2008
EN 61318:2008 - 2 -
Foreword
The text of document 78/705/FDIS, future edition 3 of IEC 61318, prepared by IEC TC 78, Live working,
was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61318 on
2008-04-16.
The following dates were fixed:

– latest date by which the EN has to be implemented

at national level by publication of an identical
(dop) 2009-02-01
national standard or by endorsement

– latest date by which the national standards conflicting
(dow) 2013-05-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61318:2007 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61243-1 NOTE  Harmonized as EN 61243-1:2005 (modified).
___________

---------------------- Page: 4 ----------------------

SIST EN 61318:2008
- 3 - EN 61318:2008

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

ISO 2859 Series Sampling procedures for inspection by - -
attributes

---------------------- Page: 5 ----------------------

SIST EN 61318:2008

---------------------- Page: 6 ----------------------

SIST EN 61318:2008
IEC 61318
Edition 3.0 2007-11
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Live working – Conformity assessment applicable to tools, devices and
equipment

Travaux sous tension – Evaluation de la conformité applicable à l'outillage, au
matériel et aux dispositifs

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMIS
...