EN 61347-1:2015
(Main)Lamp controlgear - Part 1: General and safety requirements
Lamp controlgear - Part 1: General and safety requirements
NEW! IEC 61347-1:2015 is available as IEC Standards+ 61347-1:2015 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 61347-1:2015 specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2007, Amendment 1:2010 and Amendment 2:2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) additional marking requirements; b) additional requirements for creepage distances and clearances: - for working voltages with operating frequencies up to 30 kHz; - for working voltages with higher operating frequencies than 30 kHz; - for impulse and resonance voltages ignition; - for basic, supplementary and reinforced insulation; - for insulation between circuits; - for coated or potted controlgear; c) modification of definition of ELV and FELV; d) modification of schematic drawing, showing the different controlgear classification and insulation requirements; e) scope extension; f) new Annex A: test to establish whether a conductive part is a live part which may cause an electric shock; g) new Annex M: creepage distances and clearances for controlgear where a higher degree of availability (impulse withstand category III) may be requested; h) new Annex Q: example for Up calculation; i) new Annex P: creepage distances and clearances and distance through isolation (DTI) for lamp controlgear which are protected against pollution by the use of coating or potting; j) new Annex R: concept of creepage distances and clearances.
Geräte für Lampen - Teil 1: Allgemeine und Sicherheitsanforderungen
Appareillages de lampes - Partie 1: Exigences générales et exigences de sécurité
NEW! IEC 61347-1:2015 est disponible sous forme de IEC Standards+ 61347-1:2015 qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente. L'IEC 61347-1:2015 spécifie les exigences générales et les exigences de sécurité pour les appareillages de lampes destinés à être utilisés sur des alimentations à courant continu jusqu'à 250 V et/ou sur des alimentations à courant alternatif jusqu'à 1 000 V à 50 Hz ou 60 Hz. Cette troisième édition annule et remplace la deuxième édition parue en 2007, l'Amendement 1:2010 et l'Amendement 2:2012. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
a) les exigences de marquage supplémentaires; b) des exigences supplémentaires pour les lignes de fuite et écartements: - pour des tensions de service avec des fréquences de fonctionnement jusqu'à 30 kHz; - pour des tensions de service avec des fréquences de fonctionnement supérieures à 30 kHz; - pour impulsion et la résonance des tensions d'allumage; - pour l'isolation de base, supplémentaire et renforcée; - pour l'isolation entre les circuits; - pour l'appareillage enduit ou en pot; c) modification de la définition d'ELV et de FELV; d) la modification du schéma, montrant les différentes exigences en matière de classification et d'isolation appareillage; e) extension de l'objet; f) la nouvelle Annexe A: essai pour déterminer si une partie conductrice est une partie active qui peut provoquer un choc électrique; g) la nouvelle Annexe M: les lignes de fuite et écartements pour l'appareillage où un plus haut degré de disponibilité (tenue aux chocs de catégorie III) peut être demandée; h) la nouvelle Annexe Q: exemple de calcul Up; i) la nouvelle Annexe P: les distances des lignes de fuite l'écartement et la distance à travers l'isolation (DTI) pour les appareillages de lampes qui sont protégés contre la pollution par l'utilisation d'un revêtement ou d'enrobage; j) la nouvelle Annexe R: concept de lignes de fuite et écartements.
Stikalne naprave za sijalke - 1. del: Splošne in varnostne zahteve
Ta del standarda IEC 61347 določa splošne in varnostne zahteve za stikalne naprave za sijalke za uporabo pri enosmernem napajanju do 250 V in/ali izmeničnem napajanju do 1000 V pri 50 Hz ali 60 Hz. Ta standard obravnava tudi stikalne naprave za sijalke, ki še niso standardizirane. Preskusi, obravnavani v tem standardu, so tipski preskusi. Zahteve za preskušanje posameznih stikalnih naprav za sijalke med proizvodnjo niso vključene. Zahteve za polsvetilke so podane v standardu IEC 60598-1:2014 (glej definicijo 1.2.60). Posebne zahteve za stikalne naprave, ki zagotavljajo varnostno nizko napetost (v nadaljevanju: SELV) so navedene v dodatku L. Pričakuje se lahko, da stikalne naprave za sijalke, ki so v skladu s tem standardom, ne bodo ogrožale varnosti med 90 % do 110 % nazivne napajalne napetosti pri neodvisni rabi in kadar delujejo v svetilkah, ki so v skladu z varnostnim standardom IEC 60598-1 in ustreznim delom standarda IEC 60598-2-xx, ter v sijalkah, ki so v skladu z ustreznimi standardi za sijalke. Za zahteve glede zmogljivosti so potrebne strožje omejitve.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2015
1DGRPHãþD
SIST EN 61347-1:2008
Stikalne naprave za sijalke - 1. del: Splošne in varnostne zahteve
Lamp controlgear - Part 1: General and safety requirements
Geräte für Lampen -- Teil 1: Allgemeine und Sicherheitsanforderungen
Appareillages de lampes -- Partie 1: Exigences générales et exigences de sécurité
Ta slovenski standard je istoveten z: EN 61347-1:2015
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 61347-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2015
ICS 29.140.99 Supersedes EN 61347-1:2008
English Version
Lamp controlgear - Part 1: General and safety requirements
(IEC 61347-1:2015)
Appareillages de lampes - Partie 1: Exigences générales et Geräte für Lampen - Teil 1: Allgemeine und
exigences de sécurité Sicherheitsanforderungen
(IEC 61347-1:2015) (IEC 61347-1:2015)
This European Standard was approved by CENELEC on 2015-03-26. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61347-1:2015 E
Foreword
The text of document 34C/1118/FDIS, future edition 3 of IEC 61347-1, prepared by SC 34C, "Auxiliaries
for lamps", of IEC TC 34, "Lamps and related equipment", was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 61347-1:2015.
The following dates are fixed:
(dop) 2015-12-26
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2018-03-26
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61347-1:2008
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment Designed
for Use within Certain Voltage Limits (LVD - 2006/95/EC).
Endorsement notice
The text of the International Standard IEC 61347-1:2015 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60038 NOTE Harmonized as EN 60038.
IEC 60155:1993 NOTE Harmonized as EN 60155:1995.
IEC 60364-4-44 NOTE Harmonized as HD 60364-4-444.
IEC 60598 (Series) NOTE Harmonized as EN 60598 (Series).
IEC 60664-3 NOTE Harmonized as EN 60664-3.
IEC 60925:1989 NOTE Harmonized as EN 60925:1991.
IEC 60925:1989/AMD1:1996 NOTE Harmonized as EN 60925:1991/A1:1996.
IEC 60925:1989/AMD2:2001 NOTE Harmonized as EN 60925:1991/A2:2001.
IEC 60927:2007 NOTE Harmonized as EN 60927:2007.
IEC 60927:2007/AMD1:2013 NOTE Harmonized as EN 60927:2007/A1:2013.
- 3 - EN 61347-1:2015
IEC 60929:2006 NOTE Harmonized as EN 60929:2006.
IEC 60950-1 NOTE Harmonized as EN 60950-1.
IEC 60990:1999 NOTE Harmonized as EN 60990:1999.
IEC 61047:2004 NOTE Harmonized as EN 61047:2004.
IEC 61347-2-1:2000 NOTE Harmonized as EN 61347-2-1:2001.
IEC 61347-2-1:2000/AMD1:2005 NOTE Harmonized as EN 61347-2-1:2001/A1:2006.
IEC 61347-2-2:2011 NOTE Harmonized as EN 61347-2-2:2012.
IEC 62384 NOTE Harmonized as EN 62384.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60065 (mod) 2001 Audio, video and similar electronic EN 60065 2002
apparatus - Safety requirements
- - +corrigendum Mar. 2006
- - +corrigendum Aug. 2007
- - +A11 2008
- - +A12 2011
IEC 60068-2-14 2009 Environmental testing -- Part 2-14: Tests - EN 60068-2-14 2009
Test N: Change of temperature
IEC 60081 - Double-capped fluorescent lamps - EN 60081 -
Performance specifications
IEC 60085 2007 Electrical insulation - Thermal evaluation EN 60085 2008
and designation
IEC 60112 2003 Method for the determination of the proof EN 60112 2003
and the comparative tracking indices of solid
insulating materials
+A1 2009 +A1 2009
IEC 60216 series Electrical insulating materials - Thermal EN 60216 series
endurance properties -- Part 1: Ageing
procedures and evaluation of test results
IEC 60317-0-1 2013 Specifications for particular types of winding EN 60317-0-1 2014
wires -- Part 0-1: General requirements -
Enamelled round copper wire
IEC 60384-14 - Fixed capacitors for use in electronic EN 60384-14 -
equipment -- Part 14: Sectional specification
- Fixed capacitors for electromagnetic
interference suppression and connection to
the supply mains
IEC 60417 - Graphical symbols for use on equipment. HD 243 S12 -
Index, survey and compilation of the single
sheets.
- - +corrigendum Oct. -
+A1 1979 - -
IEC 60449 1973 Voltage bands for electrical installations of HD 193 S2 1982
buildings
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code)
- - +corrigendum May 1993
+A1 1999 +A1 2000
+A2 2013 +A2 2013
IEC 60598-1 (mod) 2014 Luminaires -- Part 1: General requirements EN 60598-1 2015
and tests
- 5 - EN 61347-1:2015
IEC 60598-2 series Luminaires -- Part 2: Particular requirements EN 60598-2 series
-- Section 1: Fixed general purpose
luminaires
IEC 60664-1 2007 Insulation coordination for equipment within EN 60664-1 2007
low-voltage systems -- Part 1: Principles,
requirements and tests
IEC 60664-4 2005 Insulation coordination for equipment within EN 60664-4 2006
low-voltage systems -- Part 4: Consideration
of high-frequency voltage stress
- - +corrigendum Oct. 2006
IEC 60691 2002 Thermal-links - Requirements and EN 60691 2003
application guide
IEC 60695-2-10 - Fire hazard testing -- Part 2-10: Glowing/hot-EN 60695-2-10 -
wire based test methods - Glow-wire
apparatus and common test procedure
IEC 60695-11-5 - Fire hazard testing -- Part 11-5: Test flames EN 60695-11-5 -
- Needle-flame test method - Apparatus,
confirmatory test arrangement and guidance
IEC 60730-2-3 - Automatic electrical controls for household EN 60730-2-3 -
and similar use -- Part 2-3: Particular
requirements for thermal protectors for
ballasts for tubular fluorescent lamps
IEC 60884-2-4 - Plugs and socket-outlets for household and - -
similar purposes -- Part 2-4: Particular
requirements for plugs and socket-outlets for
SELV
IEC 60901 - Single-capped fluorescent lamps - EN 60901 -
Performance specifications
IEC 60906-3 - IEC System of plugs and socket-outlets for - -
household and similar purposes -- Part 3:
SELV plugs and socket-outlets, 16 A 6V, 12
V, 24 V, 48 V, a.c. and d.c.
IEC 60921 2004 Ballasts for tubular fluorescent lamps - EN 60921 2004
Performance requirements
+A1 2006 +A1 2006
IEC 60923 2005 Auxiliaries for lamps - Ballasts for discharge EN 60923 2005
lamps (excluding tubular fluorescent lamps)
- Performance requirements
IEC 60950-1 - Information technology equipment - Safety -- EN 60950-1 -
Part 1: General requirements
- - +A11 -
- - +A12 -
- - +AC -
IEC 61180-1 1992 High-voltage test techniques for low-voltage EN 61180-1 1994
equipment -- Part 1: Definitions, test and
procedure requirements
IEC 61189-2 2006 Test methods for electrical materials, printed EN 61189-2 2006
boards and other interconnection structures
and assemblies -- Part 2: Test methods for
materials for interconnection structures
IEC 61249-2 series Materials for printed boards and other EN 61249-2 series
interconnecting structures -- Part 2-1:
Reinforced base materials, clad and unclad -
Phenolic cellulose paper reinforced
laminated sheets, economic grade, copper-
clad
IEC 61347-2 series Lamp controlgear -- Part 2-1: Particular EN 61347-2 series
requirements for starting devices (other than
glow starters)
- - +corrigendum Jul. -
- - +corrigendum Dec. -
IEC 61347-2-8 - Lamp controlgear -- Part 2-8: Particular EN 61347-2-8 -
requirements for ballasts for fluorescent
lamps
- - +corrigendum Jul. -
- - +corrigendum Dec. -
IEC 61347-2-9 2012 Lamp controlgear -- Part 2-9: Particular EN 61347-2-9 2013
requirements for electromagnetic
controlgear for discharge lamps (excluding
fluorescent lamps)
IEC 61558-1 2005 Safety of power transformers, power EN 61558-1 2005
supplies, reactors and similar products --
Part 1: General requirements and tests
- - +corrigendum Aug. 2006
IEC 61558-2-6 2009 Safety of transformers, reactors, power EN 61558-2-6 2009
supply units and similar products for supply
voltages up to 1 100 V -- Part 2-6: Particular
requirements and tests for safety isolating
transformers and power supply units
incorporating safety isolating transformers
IEC 61558-2-16 2009 Safety of transformers, reactors, power EN 61558-2-16 2009
supply units and similar products for
voltages up to 1 100 V -- Part 2-16:
Particular requirements and tests for switch
mode power supply units and transformers
for switch mode power supply units
ISO 4046-4 2002 Paper, board, pulps and related terms - - -
Vocabulary -- Part 4: Paper and board
grades and converted products
IEC 61347-1 ®
Edition 3.0 2015-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Lamp controlgear –
Part 1: General and safety requirements
Appareillages de lampes –
Partie 1: Exigences générales et exigences de sécurité
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.99 ISBN 978-2-8322-2243-0
– 2 – IEC 61347-1:2015 © IEC 2015
CONTENTS
FOREWORD . 9
INTRODUCTION . 11
1 Scope . 12
2 Normative references . 12
3 Terms and definitions . 14
4 General requirements . 22
5 General notes on tests . 22
6 Classification . 23
7 Marking . 24
7.1 Items to be marked . 24
7.2 Durability and legibility of marking. 26
8 Terminals . 26
9 Earthing .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.