EN 60695-2-11:2014
(Main)Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014)
NEW! IEC 60695-2-11:2014 is available as IEC Standards+ 60695-2-11:2014 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition. IEC 60695-2-11:201 4 specifies a test method on an end product. It is intended to simulate the effects of thermal stresses produced by an electrically heated source to represent a fire hazard. This test method is used to check that, under defined test conditions, an end product exposed to an electrically heated source has either a limi ted ability to ignite or, if it ignites, a limited ability to propa gate flame. However, the fire hazard analysis, the flammability aspects and the flame spreading to other products are not covered by the present standard. This second edition of IEC 60695-2-11 cancels and replaces the first edition of IEC 60695-2-11 published in 2000. It constitutes a technical revision. The main changes with respect to the previous edition are: - the Introduction has been added to provide background and how it relates to the Scope, - the Scope has been modified for greater clarity and reference to basic safety publications, - numerous terms and definitions relevant to this Standard have been added to Clause 3, - the application of 'small parts' and 'insignificant mass' have been introduced and clarified, - the different types of specimens, how to specify them, and limitations of the test method have been further clarified in Clause 4, - clarified in Clause 5 the distance to specified layer when unknown, - the information from Clause 6 has been moved into the test procedure in Clause 8, - the conditioning of the specified layer and the laboratory ambient test conditions were clarified in Clause 7, - measurement of the maximum flame height was removed from Clause 9, - the reference to this test as 'GWEPT' was introduced along with an applicable title change and - Annex A has been revised to reflect current practice by prominent product committees. This standard has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51. This standard is to be used in conjunction with IEC 60695-2-10. Key words: Glowing/hot-wire, Glow wire, Flammability, Fire hazard
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-11: Prüfungen mit dem Glühdraht - Prüfung mit dem Glühdraht zur Entflammbarkeit von Enderzeugnissen (GWEPT) (IEC 60695-2-11:2014)
Essais relatifs aux risques du feu - Partie 2-11: Essais au fil incandescent/chauffant - Méthode d'essai d'inflammabilité pour produits finis (GWEPT) (CEI 60695-2-11:2014)
NEW! IEC 60695-2-11:2014 est disponible sous forme de IEC Standards+ 60695-2-11:2014 qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente. IEC 60695-2-11:2014 spécifie une méthode d'essai applicable au produit fini. Elle est destinée à simuler l'effet de contraintes thermiques produites par une source chauffée électriquement afin de représenter un danger d'incendie. La présente méthode d'essai permet de vérifier que, dans des conditions d'essai définies, un produit fini exposé à une source chauffée électriquement présente une aptitude limitée à s'enflammer ou, s'il s'enflamme, une aptitude limitée à propager la flamme. Cependant, la présente norme ne traite pas de l'analyse du danger d'incendie, des aspects d'inflammabilité et de propagation de flammes à d'autres produits. Cette deuxième édition de la CEI 60695-2-11 annule et remplace la première édition de la CEI 60695-2-11 publiée en 2000. Elle constitue une révision technique. Les principales modifications apportées par rapport à l'édition précédente sont énumérées ci-dessous: - l'introduction a été modifiée pour fournir le contexte et montrer la relation avec le domaine d'application, - modification du domaine d'application pour davantage de clarté, et pour faire référence aux publications fondamentales de sécurité, - ajout à l'Article 2 de nombreux termes et définitions applicables à la présente Norme, - introduction et clarification de l'application des 'petites pièces' et de la 'masse négligeable', - clarification supplémentaire à l'Article 4 des différents types d'éprouvettes, de la manière de les spécifier et des limitations de la méthode d'essai, - clarification à l'Article 5 de la distance par rapport à la sous-couche spécifiée, lorsqu'elle n'est pas connue, - transfert des informations de l'Article 6 dans la procédure d'essai de l'Article 8, - clarification à l'Article 7 du conditionnement de la sous-couche spécifiée et des conditions d'essai ambiantes de laboratoire, - suppression de la mesure de la hauteur de flamme maximale de l'Article 9, - introduction de la référence à cet essai comme essai 'GWEPT', et modification du titre en conséquence et - la révision de l'Annexe A, afin de refléter les pratiques en vigueur au sein des comités de produits clés. Elle a le statut d'une publication fondamentale de sécurité, conformément au Guide CEI 104 et au Guide ISO/CEI 51. Cette norme doit être utilisée conjointement avec la CEI 60695-2-10. Mots-clés: fil incandescent/chauffant, fil incandescent, inflammabilité, risque du feu
Preskušanje požarne ogroženosti - 2-11. del: Preskusne metode z žarilno žico - Preskušanje vnetljivosti končnega proizvoda z žarilno žico in navodila IEC (GWEPT) (IEC 60695-2-11:2014)
Standard EN IEC 60695-2-11 določa preskusno metodo za končni proizvod. Namenjena je poustvarjanju učinkov toplotne preobremenitve, ki jo proizvede električno ogrevani vir, s čimer se ponazori požarna ogroženost. Ta preskusna metoda se uporablja za preverjanje, ali ima pod opredeljenimi preskusnimi pogoji končni proizvod, ki je izpostavljen električno ogrevanem viru, omejeno sposobnost vžiga ali, če se vžge, omejeno sposobnost širjenja plamena. Vendar pa v tem standardu niso zajeti analiza požarne ogroženosti, vidiki vnetljivosti in širjenje plamena na druge proizvode. Ta osnovna varnostna publikacija je namenjena tehničnim odborom za pripravo standardov v skladu z načeli vodil IEC 104 in ISO/IEC 51. Ena od odgovornosti tehničnega odbora je, da kjer je to primerno, uporablja osnovne varnostne publikacije. Zahteve, preskusne metode ali preskusni pogoji iz te osnovne varnostne publikacije se ne uporabljajo, razen če so izrecno navedeni ali zajeti v ustrezne publikacije.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2014
1DGRPHãþD
SIST EN 60695-2-11:2002
3UHVNXãDQMHSRåDUQHRJURåHQRVWLGHO3UHVNXVQHPHWRGH]åDULOQRåLFR
3UHVNXãDQMHYQHWOMLYRVWLNRQþQHJDSURL]YRGD]åDULOQRåLFRLQQDYRGLOD,(&
*:(37,(&
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire
flammability test method for end-products (GWEPT)
Prüfungen zur Beurteilung der Brandgefahr - Teil 2-11: Prüfungen mit dem Glühdraht -
Prüfung mit dem Glühdraht zur Entflammbarkeit von Enderzeugnissen
Essais relatifs aux risques du feu - Partie 2-11: Essais au fil incandescent/chauffant -
Méthode d'essai d'inflammabilité pour produits finis
Ta slovenski standard je istoveten z: EN 60695-2-11:2014
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN 60695-2-11
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 13.220.40; 29.020 Supersedes EN 60695-2-11:2001
English Version
Fire hazard testing - Part 2-11: Glowing/hot-wire based test
methods - Glow-wire flammability test method for end-products
(GWEPT)
(IEC 60695-2-11:2014)
Essais relatifs aux risques du feu - Partie 2-11: Essais au fil Prüfungen zur Beurteilung der Brandgefahr - Teil 2-11:
incandescent/chauffant - Méthode d'essai d'inflammabilité Prüfungen mit dem Glühdraht - Prüfung mit dem Glühdraht
pour produits finis (GWEPT) zur Entflammbarkeit von Enderzeugnissen (GWEPT)
(CEI 60695-2-11:2014) (IEC 60695-2-11:2014)
This European Standard was approved by CENELEC on 2014-03-13. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60695-2-11:2014 E
Foreword
The text of document 89/1197/FDIS, future edition 2 of IEC 60695-2-11, prepared by IEC/TC 89 "Fire
hazard testing" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2015-01-11
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2017-03-13
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60695-2-11:2001.
EN 60695-2-11:2001:
– The Introduction has been added to provide background and how it relates to the Scope.
– The Scope has been modified for greater clarity and reference to basic safety
publications.
– Numerous terms and definitions relevant to this Standard have been added to Clause 3.
– The application of “small parts” and “insignificant mass” have been introduced and
clarified.
– The different types of specimens, how to specify them, and limitations of the test method
have been further clarified in Clause 4.
– Clarified in Clause 5 the distance to specified layer when unknown.
– The information from Clause 6 has been moved into the test procedure in Clause 8.
– The conditioning of the specified layer and the laboratory ambient test conditions were
clarified in Clause 7.
– Measurement of the maximum flame height was removed from Clause 9.
– The reference to this test as “GWEPT” was introduced along with an applicable title
change.
– Annex A has been revised to reflect current practice by prominent product committees.
This standard is to be used in conjunction with EN 60695-2-10.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
- 3 - EN 60695-2-11:2014
Endorsement notice
The text of the International Standard IEC 60695-2-11:2014 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60695-1-10 NOTE Harmonised as EN 60695-1-10 (not modified).
IEC 60695-1-11 NOTE Harmonised as EN 60695-1-11 (not modified).
IEC 60695-2-12 NOTE Harmonised as EN 60695-2-12 (not modified).
IEC 60695-2-13 NOTE Harmonised as EN 60695-2-13 (not modified).
IEC 60335-1 NOTE Harmonised as EN 60335-1 (modified).
IEC 60695-4:2012 NOTE Harmonised as EN 60695-4:2012 (not modified).
ISO/IEC 13943:2008 NOTE Harmonised as EN ISO 13943:2010.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
ISO/IEC Guide 51 Safety aspects - Guidelines for their inclusion - -
in standards
IEC Guide 104 The preparation of safety publications and the - -
use of basic safety publications and group
safety publications
IEC 60695-2-10 Fire hazard testing - Part 2-10: Glowing/hot- EN 60695-2-10
wire based test methods - Glow-wire
apparatus and common test procedure
IEC 60695-2-11 ®
Edition 2.0 2014-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
BASIC SAFETY PUBLICATION
PUBLICATION FONDAMENTALE DE SÉCURITÉ
Fire hazard testing –
Part 2-11: Glowing/hot-wire based test methods – Glow-wire flammability test
method for end-products (GWEPT)
Essais relatifs aux risques du feu –
Partie 2-11: Essais au fil incandescent/chauffant – Méthode d’essai
d’inflammabilité pour produits finis (GWEPT)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX P
ICS 13.220.40, 29.020 ISBN 978-2-8322-1373-5
– 2 – 60695-2-11 © IEC:2014
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Test specimens . 8
4.1 General . 8
4.2 Complete end product . 8
4.3 Partial end product (alternative) . 8
4.4 Test considerations and limitations associated with the specimen
configuration . 9
5 Test apparatus . 10
6 Verification of the temperature measuring system . 10
7 Conditioning . 10
7.1 Conditioning of test specimens . 10
7.2 Conditioning of specified layers . 10
7.3 Testing conditions . 10
8 Test procedure . 10
8.1 General . 10
8.2 Test temperatures . 11
8.3 Number of test specimens . 11
9 Observations and measurements . 11
10 Evaluation of test results . 12
11 Test report . 12
12 Information to be given in the relevant product standard . 12
Annex A (informative) Suggested GWEPT temperatures . 13
Bibliography . 14
Figure 1 – Small parts . 9
Figure A.1 – Suggested GWEPT temperatures . 13
Table 1 – Test temperatures . 11
60695-2-11 © IEC:2014 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIRE HAZARD TESTING –
Part 2-11: Glowing/hot-wire based test methods –
Glow-wire flammability test method for end-products (GWEPT)
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.