EN 60440:2012
(Main)Method of measurement of non-linearity in resistors
Method of measurement of non-linearity in resistors
Standardizes a method of measurement and associated test conditions for determining the magnitude of non-linear distortion generated in a resistor. Has the status of a technical report. The contents of the corrigendum of September 1974 have been included in this copy.
Verfahren zur Messung der Nichtlinearität von Widerständen
Méthode de mesure de la non-linéarité des résistances
Normalise une méthode de mesure et les conditions d'essai associées pour déterminer l'amplitude de la distorsion non linéaire engendrée dans une résistance. Cette publication a le statut d'un rapport. Le contenu du corrigendum de septembre 1974 a été pris en considération dans cet exemplaire.
Metoda merjenja nelinearnosti uporov
Preskušanje nelinearnosti je metoda za vrednotenje neoporečnosti upornega elementa. Uporablja se lahko kot učinkovita serijska presejalna metoda, ki je primerna za ugotavljanje in odpravo morebitnih začetnih okvar pri pasivnih komponentah. Metoda je precej hitra in priročna, z njo povezana oprema pa je relativno cenovno ugodna. Značilni učinki, ki povzročajo nelinearnost uporov, so npr. nehomogene pike z uporno plastjo, sledovi plasti, ki so ostali na spiralnih utorih, ali nestabilen stik med vodnikom za povezavo ali prekinitev in upornim elementom. Ta mednarodni standard določa metodo za merjenje in s tem povezane preskusne pogoje za vrednotenje razsežnosti nelinearnega popačenja v uporu. Ta metoda se uporablja, če jo predpisuje specifikacija ustreznega sestavnega dela ali se o tem dogovorita kupec in proizvajalec.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Metoda merjenja nelinearnosti uporovVerfahren zur Messung der Nichtlinearitaet von WiderstaendenMéthode de mesure de la non-linéarité des résistancesMethod of measurement of non-linearity in resistors31.040.01Upori splošnoResistors in generalICS:Ta slovenski standard je istoveten z:EN 60440:2012SIST EN 60440:2012en01-oktober-2012SIST EN 60440:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD EN 60440 NORME EUROPÉENNE
EUROPÄISCHE NORM August 2012
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60440:2012 E
ICS 31.040
English version
Method of measurement of non-linearity in resistors (IEC 60440:2012)
Méthode de mesure
de la non-linéarité des résistances (CEI 60440:2012)
Verfahren zur Messung
der Nichtlinearität von Widerständen (IEC 60440:2012)
This European Standard was approved by CENELEC on 2012-08-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60440:2012 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60027 Series NOTE Harmonised as EN 60027 Series (not modified). ISO 80000-1 NOTE Harmonised as EN ISO 80000-1.
- 3 - EN 60440:2012 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing -
Part 1: General and guidance EN 60068-1 -
IEC 60440 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Method of measurement of non-linearity in resistors
Méthode de mesure de la non-linéarite des résistances
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE Q ICS 31.040 PRICE CODE CODE PRIX ISBN 978-2-83220-228-9
– 2 – 60440 © IEC:2012 CONTENTS
FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 Terms and definitions . 5 4 Method of measurement . 6 4.1 Measurement principle . 6 4.2 Measuring circuit . 8 4.3 Measurement system requirements . 9 4.3.1 Measuring frequency . 9 4.3.2 Noise level of the measuring system . 9 4.3.3 Third harmonic ratio of the measuring system . 9 4.3.4 Power amplifier . 9 4.3.5 Voltmeter . 10 4.3.6 Filter . 10 4.3.7 Test fixture . 10 4.4 Verification of the measuring system . 10 5 Measurement procedure . 10 5.1 Environmental conditions . 10 5.2 Preparation of specimen . 10 5.3 Measurement conditions . 10 5.4 Procedure . 11 5.5 Precautions . 11 6 Evaluation of measurement results . 11 6.1 Evaluation . 11 6.2 Requirements . 12 7 Information to be given in the relevant component specification. 12 Annex A (informative)
Reference to IEC/TR 60440 . 15 Bibliography . 16
Figure 1 – Equivalent circuit at the fundamental frequency . 6 Figure 2 – Equivalent circuit at the third harmonic frequency . 7 Figure 3 – Corrective term û . 8 Figure 4 – Block schematic of a suitable measuring system . 9
Table 1 – Recommended measuring conditions (1 of 2) . 13
60440 © IEC:2012 – 3 – INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
METHOD OF MEASUREMENT OF NON-LINEARITY IN RESISTORS
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60440 has been prepared by committee 40: Capacitors and resistors for electronic equipment. This International Standard cancels and replaces the Technical Report IEC/TR 60440, published in 1973. The major changes with regard to the Technical Report are: – change of the principle parameter’s term from “third harmonic attenuation” to “third harmonic ratio”; – addition of advice on the prescription of requirements in a relevant component specification; – addition of a set of recommended measuring conditions for a specimen with a rated dissipation of less than 100 mW; – a complete editorial revision. SIST EN 60440:2012
– 4 – 60440 © IEC:2012 The text of this standard is based on the following documents: FDIS Report on voting 40/2155/FDIS 40/2167/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be • reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
60440 © IEC:2012 – 5 – METHOD OF MEASUREMENT OF NON-LINEARITY IN RESISTORS
1 Scope Non-linearity testing is a method to evaluate the integrity of a resistive element. It may be applied as an effective inline screening method suitable to detect and eliminate potential infant mortality failures in passive components. The method is fairly rapid, convenient, and the associated equipment is relatively inexpensive. Typical effects causing non-linearity on resistors are e.g. inhomogeneous spots within a resistive film, traces of film left in the spiraling grooves, or contact instability between a connecting lead or termination and the resistive element. This International Standard specifies a method of measurement and associated test conditions to assess the magnitude of non-linear distortion generated in a resistor. This method is applied if prescribed by a relevant component specification, or if agreed between a customer and a manufacturer. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60068-1, Environmental testing – Part 1: General and guidance 3 Terms and definitions For the puposes of this docume
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.