iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50355:2003

(Main)

Railway applications - Railway rolling stock cables having special fire performance - Thin wall and standard wall - Guide to use

Railway applications - Railway rolling stock cables having special fire performance - Thin wall and standard wall - Guide to use

This European Standard gives guidance in the safe use of rolling stock cables specified in EN 50264 and EN 50306. NOTE EN 50355 will be extended in future to cover also EN 50382, which is currently under preparation. These cables should only be used for the wiring of railway rolling stock and within the limits given in the manner described in this European Standard. All these cables are for fixed installation where there is no free movement of cable, except for stresses due to typical service. This European Standard is to be applied in conjunction with the relevant product and installation standards. Stricter requirements than those given in this standard could be necessary; see in particular EN 50343. This European Standard is not applicable to - intercarriage jumpers, - cables subject to continual flexing, - pantograph cables, - coaxial and fibre optic cables, - wire wrap, - cables rated at voltages greater than 3,6/6 kV, - national types, - applications other than the cabling of railway rolling stock. Legal or statutory requirements do take precedence over the guidance given in this document. In cases where no guidance exists or where it cannot be derived from general information, it is recommended that advice should be sought from the cable manufacturer.

Bahnanwendungen - Kabel und Leitungen für Schienenfahrzeuge mit verbessertem Verhalten im Brandfall - Reduzierte Isolierwanddicken und Standard-Isolierwanddicken - Leitfaden für die Verwendung

Applications ferroviaires - Câbles à comportement au feu spécifié pour matériel roulant ferroviaire - Isolation mince et d'épaisseur normale - Guide d'emploi

Railway applications - Railway rolling stock cables having special fire performance - Thin wall and standard wall - Guide to use

General Information

Status
Withdrawn
Publication Date
25-Sep-2003
Withdrawal Date
31-May-2006
ICS
13.220.20 - Fire protection
29.060.20 - Cables
45.060.01 - Railway rolling stock in general
Technical Committee
CLC/TC 20 - Electric cables
Drafting Committee
IEC/TC 20 - IEC_TC_20
Parallel Committee
IEC/TC 20 - IEC_TC_20
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
01-Jul-2016
Completion Date
01-Jul-2016
Directive
2001/16/EC - Directive 2001/16/EC of the European Parliament and of the Council of 19 March 2001 on the interoperability of the trans-European conventional rail system
Ref Project
SIST EN 50355:2004 - Railway applications - Railway rolling stock cables having special fire performance - Thin wall and standard wall - Guide to use

Relations

Replaced By
EN 50355:2013 - Railway applications - Railway rolling stock cables having special fire performance - Guide to use
Effective Date
28-Jan-2023

Buy Standard

EN 50355:2004EN 50355:2004
PreviousNext
Standard
EN 50355:2004
English language
33 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50355:2013(Main)
Railway applications - Railway rolling stock cables having special fire performance - Guide to use
SIST EN 50355:2014

This European Standard gives guidance in the safe use of rolling stock cables specified in EN 50264, EN 50306 and EN 50382.These cables shall only be used for the wiring of railway rolling stock and within the limits given in the manner described in this European Standard. All these cables are for fixed installation where there is no free movement of cable, except for stresses due to typical service. This European Standard is to be applied in conjunction with the relevant product and installation standards. Stricter requirements than those given in this standard could be necessary; see in particular EN 50343. This European Standard is not applicable to: – intercarriage jumpers; – cables subject to continual flexing; – pantograph cables; – coaxial, data and fibre optic cables; – wire wrap; – cables rated at voltages greater than 3,6/6 kV; – applications other than the cabling of railway rolling stock; – cables requiring circuit integrity. Legal or statutory requirements do take precedence over the guidance given in this document. In cases where no guidance exists or where it cannot be derived from general information, it is recommended that advice shall be sought from the cable manufacturer.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-2-1:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 2-1: Cables with crosslinked elastomeric insulation - Single core cables
SIST EN 50264-2-1:2008

EN 50264-2-1 specifies requirements for, and constructions and dimensions of, single core cables of the following types and voltage ratings: • 0,6/1 kV unscreened, unsheathed (1 mm² to 400 mm²); • 1,8/3 kV unscreened, unsheathed (1,5 mm² to 400 mm²); • 1,8/3 kV unscreened, sheathed (1,5 mm² to 400 mm²); • 3,6/6 kV unscreened, sheathed (2,5 mm² to 400 mm²). All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90 °C and a maximum temperature for short circuit conditions of 200 °C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-2-1 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-3-1:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 3-1: Cables with crosslinked elastomeric insulation with reduced dimensions - Single core cables
SIST EN 50264-3-1:2008

EN 50264-3-1 specifies requirements for, and constructions and dimensions of, single core cables of the following types and voltage ratings: • 0,6/1 kV unscreened, unsheathed (1 mm2 to 400 mm2); • 1,8/3 kV unscreened, unsheathed (1,5 mm2 to 400 mm2); • 1,8/3 kV unscreened, sheathed (1,5 mm2 to 400 mm2); • 3,6/6 kV unscreened, sheathed (2,5 mm2 to 400 mm2). All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90° C and a maximum temperature for short circuit conditions of 200 °C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-3-1 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-3-2:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 3-2: Cables with crosslinked elastomeric insulation with reduced dimensions - Multicore cables
SIST EN 50264-3-2:2008

EN 50264-3-2 specifies requirements for, and constructions and dimensions of, multicore cables of the following types and voltage ratings: • 300/500 V screened or unscreened (1 mm2, 1,5 mm2 and 2,5 mm2, number of cores from 2 to 40); • 0,6/1 kV screened or unscreened, (1,5 mm2 to 50 mm2, 2, 3 and 4 cores). NOTE Not all conductor sizes or number of cores are specified for every type. All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90 C and a maximum temperature for short circuit conditions of 200 C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-3-2 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-1:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 1: General requirements
SIST EN 50264-1:2008

EN 50264-1 specifies the general requirements applicable to the cables given in all other parts of EN 50264. It includes the detailed requirements for the insulating and sheathing materials and other components called up in the separate parts. In particular EN 50264-1 specifies those requirements relating to fire safety. Based on proven experience and reliability over many years these cables are rated for occasional thermal stresses causing ageing equivalent to continuous operational life at a conductor temperature of 90 °C. NOTE This rating is based upon the polymers defined in 3.1 and 3.2. Before these polymers had gained widespread acceptance in the cable industry, ageing performance had been assessed via long-term thermal endurance testing and had been extrapolated to 20 000 h using techniques equivalent to those in EN 60216 (series). Subsequent experience in service has demonstrated that the predicted performance levels were correct. Where extrapolated data is used to predict lifetime in service it should be confirmed with the cable manufacturer, and should be on the basis of a failure mode appropriate to the type of material or cable. The maximum conductor temperature for short circuit conditions is 200 °C based on a duration of 5 s. This Part 1 should be read in conjunction with the other parts of EN 50264.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-2-2:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 2-2: Cables with crosslinked elastomeric insulation - Multicore cables
SIST EN 50264-2-2:2008

EN 50264-2-2 specifies requirements for, and constructions and dimensions of, multicore cables of the following types and voltage ratings: • 300/500 V screened or unscreened (1 mm², 1,5 mm² and 2,5 mm², number of cores from 2 to 40); • 0,6/1 kV screened or unscreened (1,5 mm² to 50 mm², 2, 3 and 4 cores). NOTE Not all conductor sizes or number of cores are specified for every type. All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90 °C and a maximum temperature for short circuit conditions of 200 °C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-2-2 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50355:2013(Main)
Railway applications - Railway rolling stock cables having special fire performance - Guide to use
SIST EN 50355:2014

This European Standard gives guidance in the safe use of rolling stock cables specified in EN 50264, EN 50306 and EN 50382.These cables shall only be used for the wiring of railway rolling stock and within the limits given in the manner described in this European Standard. All these cables are for fixed installation where there is no free movement of cable, except for stresses due to typical service. This European Standard is to be applied in conjunction with the relevant product and installation standards. Stricter requirements than those given in this standard could be necessary; see in particular EN 50343. This European Standard is not applicable to: – intercarriage jumpers; – cables subject to continual flexing; – pantograph cables; – coaxial, data and fibre optic cables; – wire wrap; – cables rated at voltages greater than 3,6/6 kV; – applications other than the cabling of railway rolling stock; – cables requiring circuit integrity. Legal or statutory requirements do take precedence over the guidance given in this document. In cases where no guidance exists or where it cannot be derived from general information, it is recommended that advice shall be sought from the cable manufacturer.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-3-1:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 3-1: Cables with crosslinked elastomeric insulation with reduced dimensions - Single core cables
SIST EN 50264-3-1:2008

EN 50264-3-1 specifies requirements for, and constructions and dimensions of, single core cables of the following types and voltage ratings: • 0,6/1 kV unscreened, unsheathed (1 mm2 to 400 mm2); • 1,8/3 kV unscreened, unsheathed (1,5 mm2 to 400 mm2); • 1,8/3 kV unscreened, sheathed (1,5 mm2 to 400 mm2); • 3,6/6 kV unscreened, sheathed (2,5 mm2 to 400 mm2). All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90° C and a maximum temperature for short circuit conditions of 200 °C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-3-1 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-2-2:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 2-2: Cables with crosslinked elastomeric insulation - Multicore cables
SIST EN 50264-2-2:2008

EN 50264-2-2 specifies requirements for, and constructions and dimensions of, multicore cables of the following types and voltage ratings: • 300/500 V screened or unscreened (1 mm², 1,5 mm² and 2,5 mm², number of cores from 2 to 40); • 0,6/1 kV screened or unscreened (1,5 mm² to 50 mm², 2, 3 and 4 cores). NOTE Not all conductor sizes or number of cores are specified for every type. All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90 °C and a maximum temperature for short circuit conditions of 200 °C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-2-2 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50264-2-1:2008(Main)
Railway applications - Railway rolling stock power and control cables having special fire performance - Part 2-1: Cables with crosslinked elastomeric insulation - Single core cables
SIST EN 50264-2-1:2008

EN 50264-2-1 specifies requirements for, and constructions and dimensions of, single core cables of the following types and voltage ratings: • 0,6/1 kV unscreened, unsheathed (1 mm² to 400 mm²); • 1,8/3 kV unscreened, unsheathed (1,5 mm² to 400 mm²); • 1,8/3 kV unscreened, sheathed (1,5 mm² to 400 mm²); • 3,6/6 kV unscreened, sheathed (2,5 mm² to 400 mm²). All cables have class 5 tinned copper conductors to EN 60228, halogen-free insulation and halogen-free sheath. They are for use in railway rolling stock as fixed wiring, or wiring where limited flexing in operation is encountered. The requirements provide for a continuous conductor temperature not exceeding 90 °C and a maximum temperature for short circuit conditions of 200 °C based on a duration of 5 s. Under fire conditions the cables exhibit special performance characteristics in respect of maximum permissible flame propagation (flame spread) and maximum permissible emission of smoke and toxic gases. EN 50264-2-1 should be read in conjunction with Part 1 “General requirements”.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day