iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
IEC

IEC TR 62540:2009

(Main)

Radio frequency identification (RFID) for stationary lead acid cells and monoblocs - Tentative requirements

Radio frequency identification (RFID) for stationary lead acid cells and monoblocs - Tentative requirements

IEC/TR 62540:2009(E) applies to all stationary lead-acid cells and monobloc batteries for float charge applications (i.e. permanently connected to a load and to a d.c. power supply), in a static location (i.e. not generally intended to be moved from place to place) and incorporated into stationary equipment or installed in battery rooms for use in telecom, uninterruptible power supply (UPS), utility switching, emergency power or similar applications. These batteries are covered by IEC 60896-11, IEC 60896-21 and IEC 60896-22.

General Information

Status
Published
Publication Date
24-Nov-2009
ICS
01 - GENERALITIES. TERMINOLOGY. STANDARDIZATION. DOCUMENTATION
29.220.20 - Acid secondary cells and batteries
Technical Committee
TC 21 - Secondary cells and batteries
Drafting Committee
WG 3 - TA 5/WG 3
Current Stage
PPUB - Publication issued
Start Date
15-Mar-2010
Completion Date
25-Nov-2009
Ref Project

Buy Standard

IEC TR 62540:2009 - Radio frequency identification (RFID) for stationary lead acid cells and monoblocs - Tentative requirementsIEC TR 62540:2009 - Radio frequency identification (RFID) for stationary lead acid cells and monoblocs - Tentative requirements
PreviousNext
Technical report
IEC TR 62540:2009 - Radio frequency identification (RFID) for stationary lead acid cells and monoblocs - Tentative requirements
English language
21 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC/TR 62540
®
Edition 1.0 2009-11
TECHNICAL
REPORT

Radio frequency identification (RFID) of stationary lead acid cells and
monoblocs – Tentative requirements


IEC/TR 62540:2009(E)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2009 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00

---------------------- Page: 2 ----------------------
IEC/TR 62540
®
Edition 1.0 2009-11
TECHNICAL
REPORT

Radio frequency identification (RFID) of stationary lead acid cells and
monoblocs – Tentative requirements


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
S
ICS 29.220.20 ISBN 978-2-88910-758-2
® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 3 ----------------------
– 2 – TR 62540 © IEC:2009(E)
CONTENTS
FOREWORD.3
1 Scope.5
2 Terms and definitions .5
3 Functional requirements .9
3.1 Overview .9
3.2 Data content and display requirements.10
3.3 Physical dimensions requirements.10
3.4 Performance requirements .10
3.5 Durability requirements .10
4 Requirements and characteristics.11
4.1 Requirement for information stored .11
4.2 Requirement of information display structure.14
4.3 Requirement of information translator.14
4.4 Requirement for data safety .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

IEC
IEC TR 61431:2020(Main)
Guidelines for the use of monitor systems for lead-acid traction batteries

IEC TR 61431:2020 is an informative document relating to aspects of automatic monitor systems as utilized in lead-acid traction battery applications. It lists the characteristics and features that need to be monitored and evaluated to properly assess the operative status of a traction battery. Guidance concerning the accuracy and reliability of the generated information is also provided.

  • Technical report
    18 pages
    English language
    sale 15% off
IEC
IEC 62984-3:2020(Main)
High-temperature secondary batteries - Part 3: Sodium-based batteries - Performance requirements and tests

IEC 62984-3:2020 specifies performance requirements and test procedures for high­-temperature batteries based on sodium for mobile and/or stationary use and whose rated voltage does not exceed 1 500 V.
Sodium based batteries include sodium-sulphur batteries and sodium-nickel chloride batteries; both are high-temperature batteries and use a solid, sodium conducting electrolyte. Additional information on sodium-based batteries technology, their chemistries and construction are given in Annex B.
This document does not cover aircraft batteries, covered by IEC 60952 (all parts), and batteries for the propulsion of electric road vehicles, covered by IEC 61982 (all parts).

  • Standard
    70 pages
    English and French language
    sale 15% off
IEC
IEC 62984-1:2020(Main)
High-temperature secondary batteries - Part 1: General requirements

IEC 62984-1:2020 specifies general aspects, definitions and tests for high-temperature secondary batteries for mobile and/or stationary use and whose nominal voltage does not exceed 1 500 V.
This document does not cover aircraft batteries, which are covered by IEC 60952 (all parts), or batteries for the propulsion of electric road vehicles, covered by IEC 61982 (all parts).

  • Standard
    71 pages
    English and French language
    sale 15% off
IEC
IEC 62984-2:2020(Main)
High-temperature secondary batteries – Part 2: Safety requirements and tests

IEC 62984-2:2020 specifies safety requirements and test procedures for high-temperature batteries for mobile and/or stationary use and whose rated voltage does not exceed 1 500 V.
This document does not cover aircraft batteries, which are covered by IEC 60952 (all parts), and batteries for the propulsion of electric road vehicles, covered by IEC 61982 (all parts).

  • Standard
    74 pages
    English and French language
    sale 15% off
IEC
IEC 60095-6:2019(Main)
Lead-acid starter batteries - Part 6: Batteries for micro-cycle applications

IEC 60095-6:2019 is applicable to lead-acid batteries with a nominal voltage of 12 V, used primarily as power source for the starting of internal combustion engines (ICE), lighting and also for auxiliary equipment of ICE vehicles. These batteries are commonly called "starter batteries".
The batteries within the scope of this document are used for micro-cycle applications in vehicles which can also be called start-stop (or stop-start, idling-stop system, micro-hybrid or idle-stop-and-go) applications. In cars with this special capability, the internal combustion engine is switched off during a complete vehicle stop, during idling with low speed or during idling where there is no need to support the vehicle movement by the internal combustion engine. During the phases in which the engine is switched off, most of the electric and electronic components of the car are supplied by the battery without support of the alternator. In addition, in most cases an additional regenerative braking (recuperation or regeneration of braking energy) function is installed. The batteries under these applications are stressed in a completely different way compared to classical starter batteries. Aside from these additional properties, these batteries need to crank the ICE and support the lighting and also auxiliary functions in a standard operating mode with the support of the alternator when the internal combustion engine is switched on. All batteries within this scope fulfil basic functions, which are tested under the application of IEC 60095-1.
This document specifies the general requirements and methods of test specific to lead-acid batteries used for micro-cycle applications.
This document is applicable to batteries for the following purposes:
• lead-acid batteries of the dimensions according to IEC 60095­2 for vehicles with the capability to automatically switch off the ICE during vehicle operation either in standstill or when moving ("start-stop");
• lead-acid batteries of the dimensions according to IEC 60095­2 for vehicles with start­stop applications with the capability to recover braking energy or energy from other sources.
Li-ion technology is excluded from this document.

  • Standard
    64 pages
    English and French language
    sale 15% off
IEC
IEC 60095-7:2019(Main)
Lead-acid starter batteries - Part 7: General requirements and methods of test for motorcycle batteries

IEC 60095-7:2019 is applicable to lead-acid batteries used primarily as a power source for the starting of internal combustion engines, lighting and ignition (SLI) of motorcycles and other power sport vehicles. The nominal voltage is 12 V or 6 V.
Test definitions and criteria in this document are for batteries with a nominal voltage of 12 V only. For batteries with a nominal voltage of 6 V, all voltages have to be divided by two.
The other power sports vehicles covered in this document are snowmobiles, personal water crafts and all-terrain vehicles.
This document is not applicable to batteries for other purposes, such as the back-up power sources, auxiliary equipment of internal combustion engine vehicles and e-bikes.
This document specifies:
• general requirements;
• size, essential functional characteristics, relevant test methods and results required.

  • Standard
    40 pages
    English and French language
    sale 15% off
IEC
IEC 62902:2019(Main)
Secondary cells and batteries - Marking symbols for identification of their chemistry

IEC 62902:2019 specifies methods for the clear identification of secondary cells, batteries, battery modules and monoblocs according to their chemistry (electrochemical storage technology).
The markings described in this document are applicable for secondary cells, batteries, battery modules and monoblocs with a volume of more than 900 cm3.
The marking of the chemistry is useful for the installation, operation and decommissioning phases of battery life.
Many recycling processes are chemistry specific, thus undesired events can occur when a battery which is not of the appropriate chemistry enters a given recycling process. In order to ensure safe handling during sorting and recycling processes, therefore, the battery is marked so as to identify its chemistry.
IEC 62902:2019 defines the conditions of utilization of the markings indicating the chemistry of these secondary batteries.
The details of markings and their application are defined in this document.

  • Standard
    37 pages
    English and French language
    sale 15% off
IEC
IEC 62660-2:2018(Main)
Secondary lithium-ion cells for the propulsion of electric road vehicles - Part 2: Reliability and abuse testing

IEC 62660-2:2018 is available as IEC 62660-2:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62660-2:2018 specifies test procedures to observe the reliability and abuse behaviour of secondary lithium-ion cells and cell blocks used for propulsion of electric vehicles including battery electric vehicles (BEV) and hybrid electric vehicles (HEV). This document specifies the standard test procedures and conditions for basic characteristics of lithium-ion cells for use in propulsion of battery and hybrid electric vehicles. The tests are indispensable for obtaining essential data on reliability and abuse behaviour of lithium-ion cells for use in various designs of battery systems and battery packs. This document provides standard classification of description of test results to be used for the design of battery systems or battery packs. IEC 62660-2:2018 cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) The procedure of forced discharge test has been clarified (6.4.3.2).
b) "Cell block" has been added to the scope (Clause 1).
c) Option of temperature cycling test with electrical operation has been deleted (6.3.2).
d) The test conditions for overcharge test have been revised (6.4.2.2).

  • Standard
    37 pages
    English and French language
    sale 15% off
IEC
IEC 62660-1:2018(Main)
Secondary lithium-ion cells for the propulsion of electric road vehicles - Part 1: Performance testing

IEC 62660-1:2018 is available as IEC 62660-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 62660-1:2018 specifies performance and life testing of secondary lithium-ion cells used for propulsion of electric vehicles including battery electric vehicles (BEV) and hybrid electric vehicles (HEV). This document specifies the test procedures to obtain the essential characteristics of lithium-ion cells for vehicle propulsion applications regarding capacity, power density, energy density, storage life and cycle life. This document provides the standard test procedures and conditions for testing basic performance characteristics of lithium-ion cells for vehicle propulsion applications, which are indispensable for securing a basic level of performance and obtaining essential data on cells for various designs of battery systems and battery packs. IEC 62660-1:2018 cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) The purpose of each test has been added.
b) The power test has been revised for clarification, and an informative part of the current-voltage characteristic test has been moved to the new Annex C.

  • Standard
    77 pages
    English and French language
    sale 15% off
IEC
IEC 60095-1:2018(Main)
Lead-acid starter batteries - Part 1: General requirements and methods of test

IEC 60095-1:2018 is available as IEC 60095-1:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60095-1:2018 is applicable to lead-acid batteries with a nominal voltage of 12 V, used primarily as a power source for the starting of internal combustion engines, lighting, and for auxiliary equipment of internal combustion engine vehicles. These batteries are commonly called "starter batteries".
This document is applicable to batteries for the following purposes:
• batteries for passenger cars;
• batteries for commercial and industrial vehicles.
IEC 60095-1:2018 is not applicable to batteries for other purposes, such as the starting of railcar internal combustion engines or for motorcycles and other power sport vehicles. IEC 60095-1:2018 defines many general properties of lead-acid batteries. Single sections can be referenced in other parts of the IEC 60095 series even if the application is excluded in the scope of this document. This document specifies the:
• general requirements;
• essential functional characteristics, relevant test methods and results required,
for several classes of starter batteries:
• according to the general type of application;
• according to the type of product.
IEC 60095-1:2018 cancels and replaces the seventh edition published in 2006. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) charge acceptance test;
b) cranking performance test;
c) charge retention test; and
d) endurance test added.

  • Standard
    26 pages
    English language
    sale 15% off