IEC 61784-5-14:2010
(Main)Industrial communication networks - Profiles - Part 5-14: Installation of fieldbuses - Installation profiles for CPF 14
Industrial communication networks - Profiles - Part 5-14: Installation of fieldbuses - Installation profiles for CPF 14
IEC 61784-5-14:2010 specifies the installation profiles for CPF 14 (EPA). The installation profiles are specified in the annex. This annex is read in conjunction with IEC 61918:2010. This bilingual version (2012-02) corresponds to the monolingual English version, published in 2010-07.
This publication is to be read in conjunction with IEC 61918:2010.
Réseaux de communication industriels - Profils - Partie 5-14: Installation de bus de terrain - Profils d'installation pour CPF 14
La CEI 61784-5-14:2010 spécifie les profils d'installation applicables à la CPF 14 (EPA). Les profils d'installation sont spécifiés dans l'annexe. Cette annexe est lue conjointement à la CEI 61918:2010. La présente version bilingue (2012-02) correspond à la version anglaise monolingue publiée en 2010-07.
Cette publication doit être lue conjointement avec la CEI 61918:2010.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61784-5-14 ®
Edition 1.0 2010-07
INTERNATIONAL
STANDARD
colour
inside
Industrial communication networks – Profiles –
Part 5-14: Installation of fieldbuses – Installation profiles for CPF 14
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00
IEC 61784-5-14 ®
Edition 1.0 2010-07
INTERNATIONAL
STANDARD
colour
inside
Industrial communication networks – Profiles –
Part 5-14: Installation of fieldbuses – Installation profiles for CPF 14
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
U
ICS 25.040.40; 35.100.40 ISBN 978-2-88912-060-4
– 2 – 61784-5-14 © IEC:2010(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
2 Normative references .7
3 Terms, definitions and abbreviated terms .7
4 CPF 14: Overview of installation profiles .7
5 Installation profile conventions .7
6 Conformance to installation profiles.8
Annex A (normative) CP 14/1 and 14/2 (EPA) specific installation profile.9
Figure 1 – Standards relationships.6
Figure A.1 – Example of EPA explosion-proof system.10
Figure A.2 – Earth of zener safety barrier .11
Figure A.3 – Earth of zener safety barrier .11
Figure A.4 – Example of power with Ethernet.14
Figure A.5 – Example of power supply over 0,2 A .15
Figure A.6 – Pin assignment of sub-D connector.24
Figure A.7 – Example of a 4-pin open style connector.25
Figure A.8 –Example of a 6-pin open style connector.26
Figure A.9 –– Example of an 8-pin open style connector.27
Table A.1 – Network characteristics for balanced cabling based on Ethernet .12
Table A.2 – Network characteristics for optical fibre cabling.13
Table A.3 – Information relevant to copper cable .15
Table A.4 –Information relevant to copper cable: fixed cables.16
Table A.5 – Information relevant to copper cable: cords.16
Table A.6 – Information relevant to optical fibre cables .17
Table A.7 – Connectors for balanced cabling CPs based on Ethernet .18
Table A.8 – Optical fibre connecting hardware .18
Table A.9 –Relationship between FOC and fibre types (CP 14/1 and CP 14/2) .19
Table A.10 – Specific connectors for balanced cabling based on Ethernet .19
Table A.11 Requirements of sub-D and open style connector .19
Table A.12 – Parameters for balanced cables .22
Table A.13 – Parameters for silica optical fibre cables .22
Table A.14 – Parameters for POF optical fibre cables .23
Table A.15 – Parameters for hard cladded silica optical fibre cables .23
Table A.16 – Signal lines assignment of sub-D connector .24
Table A.17 – Signal lines assignment of sub-D connector for 1 000 Base Ethernet .25
Table A.18 – Signal lines assignment for a 4-pin open style connector .26
Table A.19 – Signal lines assignment for a 6-pin open style connector .27
61784-5-14 © IEC:2010(E) – 3 –
Table A.20 – Signal lines assignment for an 8-pin open style connector(10/100 Mbit/s) .28
Table A.21 – Signal lines assignment for an 8-pin open style connector(1 000 Mbit/s) .28
– 4 – 61784-5-14 © IEC:2010(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –
Part 5-14: Installation of fieldbuses –
Installation profiles for CPF 14
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61784-5-14 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This standard is to be used in conjunction with IEC 61918:2010.
61784-5-14 © IEC:2010(E) – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
65C/602/FDIS 65C/616/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61784-5 series, published under the general title Industrial
communication networks – Profiles – Installation of fieldbuses, can be found on the IEC
website.
The committee has decided that the contents of this publication will remain unchanged until
the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
– 6 – 61784-5-14 © IEC:2010(E)
INTRODUCTION
This International Standard is one of a series produced to facilitate the use of communication
networks in industrial control systems.
IEC 61918:2010 provides the common requirements for the installation of communication
networks in industrial control systems. This installation profile standard provides the
installation profiles of the communication profiles (CP) of a specific communication profile
family (CPF) by stating which requirements of IEC 61918 fully apply and, where necessary, by
supplementing, modifying, or replacing the other requirements (see Figure 1).
For general background on fieldbuses, their profiles, and relationship between the installation
profiles specified in this standard, see IEC/TR 61158-1.
Each CP installation profile is specified in a separate annex of this standard. Each annex is
structured exactly as the reference standard IEC 61918 for the benefit of the persons
representing the roles in the fieldbus installation process as defined in IEC 61918 (planner,
installer, verification personnel, validation personnel, maintenance personnel, administration
personnel). By reading the installation profile in conjunction with IEC 61918, these persons
immediately know which requirements are common for the installation of all CPs and which
are modified or replaced. The conventions used to draft this standard are defined in Clause 5.
The provision of the installation profiles in one standard for each CPF (for example
IEC 61784-5-14 for CPF 14), allows readers to work with standards of a convenient size.
PLANNING
DESIGN AND
INSTALLATION
Offices
GENERIC
OFFICE PREMISES ISO/IEC 11801
Annex
CABLING
Home
HOMES ISO/IEC 15018
Annex
ISO/IEC Data centre
DATA CENTRES ISO/IEC 24764
14763-2 Annex
BETWEEN
Industrial
AUTOMATION ISO/IEC 24702
Annex
ISLANDS
BETWEEN
AUTOMATION
Installation
INDUSTRIAL PREMISES IEC 61158
IEC 61918
ISLANDS
Profiles
series
IEC 61784-5 series
and (Common
(Selection +
WITHIN
IEC 61784-1, -2 requirements)
Add/Repl/Mod)
AUTOMATION
ISLANDS
Com m on structure
APPLICATION-SPECIFIC
CABLING
Figure 1 – Standards relati
...
IEC 61784-5-14 ®
Edition 1.0 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Industrial communication networks – Profiles –
Part 5-14: Installation of fieldbuses – Installation profiles for CPF 14
Réseaux de communication industriels – Profils –
Partie 5-14: Installation de bus de terrain – Profils d'installation pour CPF 14
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé Fax: +41 22 919 03 00
CH-1211 Geneva 20 info@iec.ch
Switzerland www.iec.ch
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Useful links:
IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.
IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: csc@iec.ch.
A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
Liens utiles:
Recherche de publications CEI - www.iec.ch/searchpub Electropedia - www.electropedia.org
La recherche avancée vous permet de trouver des Le premier dictionnaire en ligne au monde de termes
publications CEI en utilisant différents critères (numéro de électroniques et électriques. Il contient plus de 30 000
référence, texte, comité d’études,…). termes et définitions en anglais et en français, ainsi que
Elle donne aussi des informations sur les projets et les les termes équivalents dans les langues additionnelles.
publications remplacées ou retirées. Egalement appelé Vocabulaire Electrotechnique
International (VEI) en ligne.
Just Published CEI - webstore.iec.ch/justpublished
Service Clients - webstore.iec.ch/csc
Restez informé sur les nouvelles publications de la CEI.
Just Published détaille les nouvelles publications parues. Si vous désirez nous donner des commentaires sur
Disponible en ligne et aussi une fois par mois par email. cette publication ou si vous avez des questions
contactez-nous: csc@iec.ch.
IEC 61784-5-14 ®
Edition 1.0 2010-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Industrial communication networks – Profiles –
Part 5-14: Installation of fieldbuses – Installation profiles for CPF 14
Réseaux de communication industriels – Profils –
Partie 5-14: Installation de bus de terrain – Profils d'installation pour CPF 14
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
U
CODE PRIX
ICS 25.040.40; 35.100.40 ISBN 978-2-88912-953-9
– 2 – 61784-5-14 IEC:2010
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and abbreviated terms . 7
4 CPF 14: Overview of installation profiles . 7
5 Installation profile conventions . 7
6 Conformance to installation profiles . 8
Annex A (normative) CP 14/1 and 14/2 (EPA) specific installation profile . 9
Figure 1 – Standards relationships . 6
Figure A.1 – Example of EPA explosion-proof system . 10
Figure A.2 – Earth of zener safety barrier . 11
Figure A.3 – Earth of zener safety barrier . 11
Figure A.4 – Example of power with Ethernet . 14
Figure A.5 – Example of power supply over 0,2 A . 15
Figure A.6 – Pin assignment of sub-D connector . 24
Figure A.7 – Example of a 4-pin open style connector . 25
Figure A.8 – Example of a 6-pin open style connector . 26
Figure A.9 – Example of an 8-pin open style connector . 27
Table A.1 – Network characteristics for balanced cabling based on Ethernet . 12
Table A.2 – Network characteristics for optical fibre cabling . 13
Table A.3 – Information relevant to copper cable . 15
Table A.4 – Information relevant to copper cable: fixed cables . 16
Table A.5 – Information relevant to copper cable: cords . 16
Table A.6 – Information relevant to optical fibre cables . 17
Table A.7 – Connectors for balanced cabling CPs based on Ethernet . 18
Table A.8 – Optical fibre connecting hardware . 18
Table A.9 – Relationship between FOC and fibre types (CP 14/1 and CP 14/2) . 19
Table A.10 – Specific connectors for balanced cabling based on Ethernet . 19
Table A.11 – Requirements of sub-D and open style connector . 19
Table A.12 – Parameters for balanced cables . 22
Table A.13 – Parameters for silica optical fibre cables . 22
Table A.14 – Parameters for POF optical fibre cables . 23
Table A.15 – Parameters for hard cladded silica optical fibre cables . 23
Table A.16 – Signal lines assignment of sub-D connector . 24
Table A.17 – Signal lines assignment of sub-D connector for 1 000 Base Ethernet . 25
Table A.18 – Signal lines assignment for a 4-pin open style connector . 26
Table A.19 – Signal lines assignment for a 6-pin open style connector . 27
61784-5-14 IEC:2010 – 3 –
Table A.20 – Signal lines assignment for an 8-pin open style connector(10/100 Mbit/s) . 28
Table A.21 – Signal lines assignment for an 8-pin open style connector(1 000 Mbit/s) . 28
– 4 – 61784-5-14 IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS –
PROFILES –
Part 5-14: Installation of fieldbuses –
Installation profiles for CPF 14
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61784-5-14 has been prepared by subcommittee 65C: Industrial
networks, of IEC technical committee 65: Industrial-process measurement, control and
automation.
This standard is to be used in conjunction with IEC 61918:2010.
This bilingual version (2012-02) corresponds to the monolingual English version, published in
2010-07.
61784-5-14 IEC:2010 – 5 –
The text of this standard is based on the following documents:
FDIS Report on voting
65C/602/FDIS 65C/616/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
The French version of this standard has not been voted upon.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 617
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.