IEC TR 60725:1981
(Main)Considerations on reference impedances for use in determining the disturbance characteristics of household appliances and similar electrical equipment
Considerations on reference impedances for use in determining the disturbance characteristics of household appliances and similar electrical equipment
Records the information that was available and the factors that were taken into account in arriving at the reference impedance of 0.4+ j 0.25 ohm which has been incorporated in IEC 60555. Has the status of a technical report.
Considérations sur les impédances de référence à utiliser pour la détermination des caractéristiques de perturbation des appareils électrodomestiques et les équipements analogues
Comprend les informations mises à disposition, ainsi que les facteurs pris en considération pour arriver à la valeur de l'impédance de référence de 0,4 + j 0,25 ohm qui a été incorporée dans la CEI 60555. Cette publication a le statut d'un rapport technique.
Considerations on reference for use in determining the disturbance characteristics of household appliances and similar electrical equipment
General Information
Standards Content (Sample)
SLOVENSKI SIST IEC/TR 60725:1998
prva izdaja
STANDARD
september 1998
Considerations on reference for use in determining the disturbance characteristics
of household appliances and similar electrical equipment
ICS 17.220.01 Referenčna št
...
This May Also Interest You
- Standard18 pagesEnglish and French languagesale 15% off
- Standard22 pagesEnglish and French languagesale 15% off
- Standard89 pagesEnglish and French languagesale 15% off
IEC 61543:2022 provides specific emission and immunity requirements, tests and performance criteria for residual current-operated protective devices (RCDs), for household and similar use, for rated voltages not exceeding 440 V.
This second edition cancels and replaces the first edition published in 1995, Amendment 1:2004 and Amendment 2:2005. This edition constitutes a technical revision.
This edition includes the following significant changes with respect to the previous edition:
some editorial modifications were introduced to comply to the ISO/IEC Directives Part 2:2021, e.g. introduction of Clause 3 – Terms and Definitions and renumbering of the whole document. In particular, the numbering of performance criteria has been changed (5.1.1, 5.1.2 become A, B, etc.);
some technical improvements:
Modification of scope and addition of Clause 6 and Clause 7 to enable the use of this document as a guideline for the preparation of EMC requirements and tests for other product standards under the scope of SC 23E;
Requirements for voltage dips and interruptions added;
Repetition rate for burst-test, defined at 5 kHz;
Surge test: Specifying impulse voltage application point and adding of voltages 2 kV, 1 kV and 0,5 kV to test T 5b;
Radiated radio-frequency electromagnetic field: Adding of frequency range 1,4 GHz to 6 GHz and specifying frequencies for the test at 1,25 IΔn;
Conducted, common mode disturbances in the frequency range 0 Hz to 150 kHz: Specifying frequencies for the test at 1,25 IΔn;
Electrostatic discharges: Change of performance criteria from 5.1.3 to B.
- Standard30 pagesEnglish and French languagesale 15% off
IEC TR 61000-1-4:2022 is available as IEC TR 61000-1-4:2022 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC TR 61000-1-4:2022 which is a technical report, reviews the sources and effects of power frequency conducted harmonic current emissions in the frequency range up to 2 kHz on the public electricity supply, and gives an account of the reasoning and calculations leading to the existing emission limits for equipment in the editions of IEC 61000-3-2, up to and including the fifth edition (2018) with Amendment 1 (2020), and in the second edition of IEC 61000-3-12. The history is traced from the first supra-national standard on low-frequency conducted emissions into the public electricity supply, EN 50006:1975 and its evolution through IEC (60)555-2 to IEC 61000-3-2, IEC TR 61000-3-4 and IEC 61000-3-12. To give a full picture of the history, that of the standard for the measuring instrument IEC 61000-4-7 is mentioned as well. NOTE All IEC standards were renumbered starting from 60000 from 1998-01-01. To indicate the references of standards withdrawn before, or not reprinted after, that date, the “60x” prefix is here enclosed in parentheses. Hence “IEC (60)555-2”. Some concepts in this document apply to all low voltage AC systems, but the numerical values apply specifically to the European 230 V/400 V 50 Hz system. This second edition cancels and replaces the first edition published in 2005. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- relation between compatibility levels, emission limits and immunity requirements clarified;
- sharing of emission levels between LV, MV and HV clarified;
- new historical information added.
- Technical report38 pagesEnglish languagesale 15% off
Specifies a procedure for the determination of the kinematic viscosity of mineral insulating oils, both transparent and opaque, at very low temperatures, after a cold soaking period of at least 20 h, by measuring the time for a volume of liquid to flow under gravity throught a calibrated glass capillary viscometer. Applies at all temperatures to both Newtonian and non-Newtonian liquids having viscosities of up to 20 000 mm2/s.
- Standard48 pagesEnglish and French languagesale 15% off
IEC 61000-4-20:2022 focuses on emission and immunity test methods for electrical and electronic equipment using various types of transverse electromagnetic (TEM) waveguides. These types include open structures (for example striplines and electromagnetic pulse simulators) and closed structures (for example TEM cells). These structures can be further classified as one-port, two-port, or multi-port TEM waveguides. The frequency range depends on the specific testing requirements and the specific TEM waveguide type. The object of this document is to describe
TEM waveguide characteristics, including typical frequency ranges and equipment-under-test (EUT) size limitations;
TEM waveguide validation methods for electromagnetic compatibility (EMC) tests;
the EUT (i.e. EUT cabinet and cabling) definition;
test set-ups, procedures, and requirements for radiated emission measurements in TEM waveguides; and
test set-ups, procedures, and requirements for radiated immunity testing in TEM waveguides. NOTE Test methods are defined in this document to measure the effects of electromagnetic radiation on equipment and the electromagnetic emissions from the equipment concerned. The simulation and measurement of electromagnetic radiation is not adequately exact for the quantitative determination of effects for all end-use installations. The test methods defined are structured for a primary objective of establishing adequate reproducibility of results at various test facilities for qualitative analysis of effects.
This document does not intend to specify the tests to be applied to any particular apparatus or system(s). The main intention of this document is to provide a general basic reference for all interested product committees of the IEC. For radiated emission measurements, product committees select emission limits and measurement methods in consultation with CISPR standards. For radiated immunity testing, product committees remain responsible for the appropriate choice of immunity tests and immunity test limits to be applied to equipment within their scope. This document describes test methods that are separate from those of IEC 61000‑4‑3.
This third edition cancels and replaces the second edition published in 2010. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
provide information on the testing of large EUTs (including cables);
apply the work on measurement uncertainties by adapting the work completed in CISPR and TC 77 (for emissions and immunity);
update the validation procedure for the test volume regarding field uniformity and TEM mode verification;
provide information concerning two-port and four-port TEM waveguides;
add a new informative annex (Annex I) dealing with transient TEM waveguide characterization; and
add information dealing with dielectric test stands for EUTs.
- Standard229 pagesEnglish and French languagesale 15% off
- Standard2 pagesEnglish and French languagesale 15% off
CISPR 25:2021 contains limits and procedures for the measurement of radio disturbances in the frequency range of 150 kHz to 5 925 MHz. This document applies to vehicles, boats, internal combustion engines, trailers, devices and any electronic/electrical component intended for use in vehicles, boats, trailers and devices. Refer to International Telecommunications Union (ITU) publications for details of frequency allocations. The limits are intended to provide protection for on-board receivers installed (per the manufacturer’s guidelines) in a vehicle from disturbances produced by components/modules in the same vehicle. The receiver types to be protected are, for example, broadcast receivers (sound and television), land mobile radio, radio telephone, amateur, citizens' radio, Satellite Navigation (GPS etc.), Wi-Fi, V2X, and Bluetooth. This document does not include protection of electronic control systems from radio frequency (RF) emissions or from transient or pulse-type voltage fluctuations. These subjects are included in ISO publications. The limits in this document are recommended and subject to modification as agreed between the customer (e.g. vehicle manufacturer) and the supplier (e.g. component manufacturer). This document is also intended to be applied by vehicle manufacturers and suppliers which are to be added and connected to the vehicle harness or to an on-board power connector after delivery of the vehicle. This document defines test methods for use by vehicle manufacturers and suppliers, to assist in the design of vehicles and components and ensure controlled levels of on-board radio frequency emissions. The emission requirements in this document are not intended to be applicable to the intentional transmissions from a radio transmitter as defined by the ITU including their spurious emissions.
NOTE 1 This exclusion is limited to those intended transmitter emissions, which leave the EUT as radiated emissions and are coupled onto the wire line in the measurement setup. For conducted transmissions on frequencies intentionally produced by the radio part of an EUT, this exclusion does not apply.
NOTE 2 It is usual for customers and suppliers to use radio regulation standards to manage the effect of spurious emissions from a radio transmitter unless limits of spurious emission are agreed in the test plan.
This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
inclusion of new frequency bands,
deletion of the annex on TEM cells,
inclusion of annexes on measurement uncertainty,
overall improvement.
- Standard372 pagesEnglish and French languagesale 15% off
- Technical report25 pagesEnglish languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.