ISO 1151-7:2023
(Main)Flight dynamics — Vocabulary — Part 7: Flight points and flight envelopes
Flight dynamics — Vocabulary — Part 7: Flight points and flight envelopes
This document defines the concepts and terms used in flight dynamics studies to specify aircraft flight conditions and envelopes. This document applies to the analysis of operational, experimental or simulated flights for the purposes of safety analyses and qualification, taking into account potential failures and likely environmental conditions.
Dynamique de vol – Vocabulaire — Partie 7: Points de vol et domaines de vol
General Information
Relations
Buy Standard
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 1151-7
Second edition
2023-11
Flight dynamics — Vocabulary —
Part 7:
Flight points and flight envelopes
Dynamique de vol – Vocabulaire —
Partie 7: Points de vol et domaines de vol
Reference number
ISO 1151-7:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 1151-7:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
© ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 1151-7:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Accomplishment of a mission . 1
3.2 Controls, geometric configuration and condition of systems . 2
3.3 State of the aircraft . 3
3.4 Environment . 4
3.5 Flight points . 5
3.6 Effective flight points . 6
3.7 Flight envelopes . 7
Bibliography . 8
Index . 9
iii
© ISO 2023 – All rights reserved
---------------------- Page: 3 ----------------------
ISO 1151-7:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO dr
...
INTERNATIONAL ISO
STANDARD 1151-7
Second edition
Flight dynamics — Vocabulary —
Part 7:
Flight points and flight envelopes
Dynamique de vol – Vocabulaire —
Partie 7: Points de vol et domaines de vol
PROOF/ÉPREUVE
Reference number
ISO 1151-7:2023(E)
© ISO 2023
---------------------- Page: 1 ----------------------
ISO 1151-7:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
PROOF/ÉPREUVE © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 1151-7:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Accomplishment of a mission . 1
3.2 Controls, geometric configuration and condition of systems . 2
3.3 State of the aircraft . 3
3.4 Environment . 4
3.5 Flight points . 5
3.6 Effective flight points . 6
3.7 Flight envelopes . 7
Bibliography . 8
Index . 9
iii
© ISO 2023 – All rights reserved PROOF/ÉPREUVE
---------------------- Page: 3 ----------------------
ISO 1151-7:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see
...
© ISO/ DIS 1151-7:2023 All rights reserved
ISO/DISPRF 1151-7:2023(E)
ISO/TC 20/SC 20/WG 2 8
Secretariat: GOST R
Date: 2023-09-28
Flight dynamics — Vocabulary — —
Part 7:
Flight points and flight envelopes
Dynamique de vol – Vocabulaire —
Partie 7: Points de vol et domaines de vol
FDIS stage
© ISO 2023 – All rights reserved
---------------------- Page: 1 ----------------------
ISO/DISPRF 1151-7:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
EmailE-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2023 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/DISPRF 1151-7:2023(E)
Contents
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 Accomplishment of a mission . 1
3.2 Controls, geometric configuration and condition of systems . 2
3.3 State of the aircraft . 3
3.4 Environment . 4
3.5 Flight points . 5
3.6 Effective flight points . 6
3.7 Flight envelopes . 7
Bibliography . 8
Index . 9
© ISO 2023 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/DISPRF 1151-7:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of
(a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.