ISO 10360-4:2000/Cor 1:2002

Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode — Technical Corrigendum 1

Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 4: MMT utilisées en mode de mesure par scanning — Rectificatif technique 1

Specifikacije geometrijskih veličin izdelka - Preskusi za sprejemljivost in ponovno verifikacijo koordinatnih merilnih strojev - 4. del: Koordinatni merilni stroji, uporabljeni kot merilni skenerji - Tehnični popravek 1

General Information

• Status: Withdrawn
• Publication Date: 19-Nov-2002
• Withdrawal Date: 19-Nov-2002
• ICS: 17.040.30 - Measuring instruments
• Technical Committee: ISO/TC 213 - Dimensional and geometrical product specifications and verification
• Drafting Committee: ISO/TC 213/WG 10 - Coordinate measuring machines
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 31-Mar-2020
• Ref Project: SIST ISO 10360-4:2002/TC 1:2003 - ISO 10360-4:2000/Cor 1:2002

Relations

• Revised: ISO 10360-5:2020 - Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 5: Coordinate measuring machines (CMMs) using single and multiple stylus contacting probing systems using discrete point and/or scanning measuring mode
• Effective Date: 23-Apr-2020
• Corrects: ISO 10360-4:2000 - Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode
• Effective Date: 06-Jun-2022
• Child: ISO 10360-4:2000 - Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode
• Effective Date: 15-Apr-2008
• Child: SIST ISO 10360-4:2002 - Geometrical Product Specifications (GPS) -- Acceptance and reverification tests for coordinate measuring machines (CMM) -- Part 4: CMMs used in scanning measuring mode
• Effective Date: 12-May-2008
• Consolidated By: ISO 9787:2013 - Robots and robotic devices — Coordinate systems and motion nomenclatures
• Effective Date: 06-Jun-2022

Standards Content (Sample)

SIST ISO 10360-4:2002/TC 1:2003SLOVENSKIjulij 2003
STANDARDSpecifikacije geometrijskih veličin izdelka - Preskusi za sprejemljivost in ponovno verifikacijo koordinatnih merilnih strojev - 4. del: Koordinatni merilni stroji, uporabljeni kot merilni skenerji - Tehnični popravek 1Geometrical Product Specifications (GPS) -
Acceptance and reverification tests for coordinate
measuring machines (CMM) - Part 4: CMMs used in
scanning measuring mode - Technical Corrigendum 1©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST ISO 10360-4:2002/TC 1:2003(en)ICS17.040.30



SIST ISO 10360-4:2002/TC 1:2003



ICS
17.040.30 Ref. No. ISO 10360-4:2000/Cor.1:2002(E)©
ISO 2002 – All rights reserved Published in Switzerland
INTERNATIONAL STANDARD ISO 10360-4:2000 TECHNICAL CORRIGENDUM 1 Published 2002-11-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION •
• ORGANISATION INTERNATIONALE DE NORMALISATION
Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode TECHNICAL CORRIGENDUM 1 Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 4: MMT utilisées en mode de mesure par scanning RECTIFICATIF TECHNIQUE 1 Technical Corrigendum 1 to ISO 10360-4:2000 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification.
Throughout ISO 10360-4:2000, symbols Replace the symbols τ, MPTτ, Tij and MPETij by the following symbols, respectively, wherever the former appear in the document. “τij”
“MPTτij” “Tij” “MPETij” SIST ISO 10360-4:2002/TC 1:2003



ISO 10360-4:2000/Cor.1:2002(E) 2 ©
ISO 2002 – All rights reserved Page 5, 5.4 Replace the penultimate paragraph of 5.4 with the following. “Record the time(s) for scanning test(s), τij, from the intermediate point at the start of the first scan sequence to the intermediate point at the end of the fourth scan sequence.” Page 5, 6.1 Replace 6.1 c) with the following. “c) the time(s) taken for
...